TMF Management Programming Manual (H06.06+, J06.03+)
Table Of Contents
- HP NonStop TMF Management Programming Manual
- Legal Notices
- Contents
- What’s New in This Manual
- About This Manual
- 1 Introduction to TMF
- 2 Communicating With the TMFSERVE Process
- 3 SPI Programming Considerations for TMF
- 4 Common Definitions
- 5 Commands and Responses
- Command Summary
- Command Descriptions
- ABORT TRANSACTION
- ADD AUDITTRAIL
- ADD DATAVOLS
- ADD DUMPS
- ADD MEDIA
- ADD RESOURCEMANAGER
- ALTER AUDITDUMP
- ALTER AUDITTRAIL
- ALTER BEGINTRANS
- ALTER CATALOG
- ALTER DATAVOLS
- ALTER DUMPS
- ALTER MEDIA
- ALTER PROCESS
- ALTER TMF
- CANCEL OPERATION
- CLOSE RESOURCEMANAGER
- DELETE CATALOG
- DELETE DATAVOLS
- DELETE DUMPS
- DELETE MEDIA
- DELETE RESOURCEMANAGER
- DELETE TMF
- DELETE TRANSACTION
- DISABLE AUDITDUMP
- DISABLE BEGINTRANS
- DISABLE DATAVOLS
- DUMP FILES
- ENABLE AUDITDUMP
- ENABLE BEGINTRANS
- ENABLE DATAVOLS
- INFO ATDUMPDM
- INFO ATVOLUME
- INFO AUDITDUMP
- INFO AUDITTRAIL
- INFO BEGINTRANS
- INFO CATALOG
- INFO DATAVOLS
- INFO DUMPS
- INFO MEDIA
- INFO PROCESS
- INFO RESOURCEMANAGER
- INFO TMF
- LIST AUDITTRAIL
- NEXT AUDITTRAIL
- RECOVER FILES
- RELOCATE DISKDUMPS
- RESOLVE TRANSACTION
- START TMF
- STATUS ATFILE
- STATUS AUDITDUMP
- STATUS AUDITTRAIL
- STATUS BEGINTRANS
- STATUS CATALOG
- STATUS DATAVOLS
- STATUS OPERATION
- STATUS RESOURCEMANAGER
- STATUS RMTRANSBRANCHES
- STATUS TMF
- STATUS TMFSERVER
- STATUS TRANSACTION
- STATUS TRANSACTIONCHILDREN
- STOP TMF
- 6 Event Messages
- 7 Error and Warning Messages
- A TMF Configuration Limits and Defaults
- Index
Commands and Responses
HP NonStop TMF Management Programming Manual—540140-010
5-164
STATUS AUDITTRAIL
ZCannotRollover
if true, specifies that the audit disk process cannot find an available audit-trail
file when the current file has become full.
ZAuditHold
if true, specifies that TMF is not allowing further audit generation because there
is very little room left in the audit trail. This condition must be alleviated by
either adding an overflow-audit volume or increasing the audit-trail capacity.
ZCommitHoldGlobalState
specifies the current TMP commit-hold status. The following values are
possible:
ZCommitHold
specifies the current status of commit-hold mode for the specified audit trail.
The following values are possible:
HeldRsnOldTransExists At least one active transaction might have sent
an audit record to this audit-trail file. The audit-
trail file remains on the active or overflow-audit
volume in case the transaction aborts, in which
case the file is needed by the backout process.
HeldRsnVolumeDown The volume on which the audit-trail file resides
is down, so TMF cannot perform the operation
needed to release the file.
HeldRsnRDF RDF requested the pinning of the file on disk,
and eventually releases the file.
ZTMF-VAL-ZLTCH-UnConfigured Not yet configured.
ZTMF-VAL-ZLTCH-On On.
ZTMF-VAL-ZLTCH-Off Off.
ZTMF-VAL-ZLTCH-Activate Activated.
ZTMF-VAL-ZLTCH-Suspend Suspended.
ZTMF-VAL-ZLTCH-UnConfigured Not yet configured.
ZTMF-VAL-ZLTCH-On On.
ZTMF-VAL-ZLTCH-Off Off.
ZTMF-VAL-ZLTCH-Activate Activated.
ZTMF-VAL-ZLTCH-Reviving Reviving.
Value (ZTMF-VAL- ) Description