TMF Management Programming Manual (H06.06+, J06.03+)
Table Of Contents
- HP NonStop TMF Management Programming Manual
- Legal Notices
- Contents
- What’s New in This Manual
- About This Manual
- 1 Introduction to TMF
- 2 Communicating With the TMFSERVE Process
- 3 SPI Programming Considerations for TMF
- 4 Common Definitions
- 5 Commands and Responses
- Command Summary
- Command Descriptions
- ABORT TRANSACTION
- ADD AUDITTRAIL
- ADD DATAVOLS
- ADD DUMPS
- ADD MEDIA
- ADD RESOURCEMANAGER
- ALTER AUDITDUMP
- ALTER AUDITTRAIL
- ALTER BEGINTRANS
- ALTER CATALOG
- ALTER DATAVOLS
- ALTER DUMPS
- ALTER MEDIA
- ALTER PROCESS
- ALTER TMF
- CANCEL OPERATION
- CLOSE RESOURCEMANAGER
- DELETE CATALOG
- DELETE DATAVOLS
- DELETE DUMPS
- DELETE MEDIA
- DELETE RESOURCEMANAGER
- DELETE TMF
- DELETE TRANSACTION
- DISABLE AUDITDUMP
- DISABLE BEGINTRANS
- DISABLE DATAVOLS
- DUMP FILES
- ENABLE AUDITDUMP
- ENABLE BEGINTRANS
- ENABLE DATAVOLS
- INFO ATDUMPDM
- INFO ATVOLUME
- INFO AUDITDUMP
- INFO AUDITTRAIL
- INFO BEGINTRANS
- INFO CATALOG
- INFO DATAVOLS
- INFO DUMPS
- INFO MEDIA
- INFO PROCESS
- INFO RESOURCEMANAGER
- INFO TMF
- LIST AUDITTRAIL
- NEXT AUDITTRAIL
- RECOVER FILES
- RELOCATE DISKDUMPS
- RESOLVE TRANSACTION
- START TMF
- STATUS ATFILE
- STATUS AUDITDUMP
- STATUS AUDITTRAIL
- STATUS BEGINTRANS
- STATUS CATALOG
- STATUS DATAVOLS
- STATUS OPERATION
- STATUS RESOURCEMANAGER
- STATUS RMTRANSBRANCHES
- STATUS TMF
- STATUS TMFSERVER
- STATUS TRANSACTION
- STATUS TRANSACTIONCHILDREN
- STOP TMF
- 6 Event Messages
- 7 Error and Warning Messages
- A TMF Configuration Limits and Defaults
- Index
Commands and Responses
HP NonStop TMF Management Programming Manual—540140-010
5-174
STATUS DATAVOLS
ZTMF-VAL-DVS-Down-Dirty
specifies configured volumes that are inaccessible, perhaps because of
device or process problems, but for which normal shutdown processing did
not complete successfully. A volume enters the downdirty state if it is down
(or goes down) during shutdown, or if data volume startup fails for any
reason.
When TMF cannot determine whether a volume is clean, the subsystem
assumes that it is dirty. Audited files on a dirty volume can contain both
logical and physical inconsistencies, but these are typically repaired by
volume recovery when the volume is restarted.
ZTMF-VAL-DVS-ShuttingDown
specifies configured volumes that are being shut down by the STOP TMF
command.
ZTMF-VAL-DVS-Disabling
Configured volumes being disabled for auditing by the DISABLE
DATAVOLS command.
ZTMF-VAL-DVS-Disabled
specifies configured volumes that are in either the disabled-clean or
disabled-dirty state. Disabled data volumes are not automatically restarted
each time they come up. Data volumes must be disabled before they can
be deleted from the configuration.
ZTMF-VAL-DVS-Disabled-Clean
specifies configured volumes that are disabled, and on which no updates
have been made to audited files since the volume last underwent a clean
shutdown. Audited files on volumes in this state do not contain any
inconsistencies.
ZTMF-VAL-DVS-Disabled-Dirty
specifies configured volumes that are disabled, but for which normal
shutdown processing did not complete successfully. A volume enters the
disabled-dirty state if it is disabled by a DISABLE DATAVOLS command
that includes the ZAbrupt field or by a TMFCOM command with the
ABRUPT option.
When TMF cannot determine whether a volume is clean, the subsystem
assumes that it is dirty. Audited files on a dirty volume can contain both
logical and physical inconsistencies, but these are typically repaired by
volume recovery when the volume is restarted.