TMF Management Programming Manual (H06.06+, J06.03+)
Table Of Contents
- HP NonStop TMF Management Programming Manual
- Legal Notices
- Contents
- What’s New in This Manual
- About This Manual
- 1 Introduction to TMF
- 2 Communicating With the TMFSERVE Process
- 3 SPI Programming Considerations for TMF
- 4 Common Definitions
- 5 Commands and Responses
- Command Summary
- Command Descriptions
- ABORT TRANSACTION
- ADD AUDITTRAIL
- ADD DATAVOLS
- ADD DUMPS
- ADD MEDIA
- ADD RESOURCEMANAGER
- ALTER AUDITDUMP
- ALTER AUDITTRAIL
- ALTER BEGINTRANS
- ALTER CATALOG
- ALTER DATAVOLS
- ALTER DUMPS
- ALTER MEDIA
- ALTER PROCESS
- ALTER TMF
- CANCEL OPERATION
- CLOSE RESOURCEMANAGER
- DELETE CATALOG
- DELETE DATAVOLS
- DELETE DUMPS
- DELETE MEDIA
- DELETE RESOURCEMANAGER
- DELETE TMF
- DELETE TRANSACTION
- DISABLE AUDITDUMP
- DISABLE BEGINTRANS
- DISABLE DATAVOLS
- DUMP FILES
- ENABLE AUDITDUMP
- ENABLE BEGINTRANS
- ENABLE DATAVOLS
- INFO ATDUMPDM
- INFO ATVOLUME
- INFO AUDITDUMP
- INFO AUDITTRAIL
- INFO BEGINTRANS
- INFO CATALOG
- INFO DATAVOLS
- INFO DUMPS
- INFO MEDIA
- INFO PROCESS
- INFO RESOURCEMANAGER
- INFO TMF
- LIST AUDITTRAIL
- NEXT AUDITTRAIL
- RECOVER FILES
- RELOCATE DISKDUMPS
- RESOLVE TRANSACTION
- START TMF
- STATUS ATFILE
- STATUS AUDITDUMP
- STATUS AUDITTRAIL
- STATUS BEGINTRANS
- STATUS CATALOG
- STATUS DATAVOLS
- STATUS OPERATION
- STATUS RESOURCEMANAGER
- STATUS RMTRANSBRANCHES
- STATUS TMF
- STATUS TMFSERVER
- STATUS TRANSACTION
- STATUS TRANSACTIONCHILDREN
- STOP TMF
- 6 Event Messages
- 7 Error and Warning Messages
- A TMF Configuration Limits and Defaults
- Index
Event Messages
HP NonStop TMF Management Programming Manual—540140-010
6-50
Descriptions of Event Messages
92: ZTMF-EVT-CantUndoAlterAT
An operator or subsystem control program (SPI requester) issued an ALTER
AUDITTRAIL command, but the command failed and some of its effects could not be
undone.
Additional Unconditional Tokens
ZTMF-TKN-EVTHDR-ProcessType
identifies the TMF process that generated the event. For this event, the value of
this token is ZTMF-VAL-PROC-TMP.
ZTMF-TKN-AuditTrailID
is the subject token of the event message, and it specifies which audit trail the
message applies to. The values are:
ZEMS-TKN-Emphasis
is set to True for this event.
Effect
The previous audit trail configuration might be corrupted, further audit trail configuration
might not be possible, and you might not be able to start TMF.
Additional Unconditional Tokens
ZTMF-TKN-EVTHDR-ProcessType token-type ZSPI-TYP-Enum.
ZTMF-TKN-AuditTrailID token-type ZSPI-TYP-Enum.
ZEMS-TKN-Emphasis token-type ZSPI-TYP-Boolean.
Event-Message Text
Cannot UNDO the effects of a failed ALTER AUDITTRAIL for the
ZTMF-TKN-AuditTrailID Audit Trail.
ZTMF-VAL-Mat Master audit trail
ZTMF-VAL-Aux01 Auxiliary audit trail #1
ZTMF-VAL-Aux02 Auxiliary audit trail #2
. . .
ZTMF-VAL-Aux15 Auxiliary audit trail #15