TMF Management Programming Manual (H06.06+, J06.03+)
Table Of Contents
- HP NonStop TMF Management Programming Manual
- Legal Notices
- Contents
- What’s New in This Manual
- About This Manual
- 1 Introduction to TMF
- 2 Communicating With the TMFSERVE Process
- 3 SPI Programming Considerations for TMF
- 4 Common Definitions
- 5 Commands and Responses
- Command Summary
- Command Descriptions
- ABORT TRANSACTION
- ADD AUDITTRAIL
- ADD DATAVOLS
- ADD DUMPS
- ADD MEDIA
- ADD RESOURCEMANAGER
- ALTER AUDITDUMP
- ALTER AUDITTRAIL
- ALTER BEGINTRANS
- ALTER CATALOG
- ALTER DATAVOLS
- ALTER DUMPS
- ALTER MEDIA
- ALTER PROCESS
- ALTER TMF
- CANCEL OPERATION
- CLOSE RESOURCEMANAGER
- DELETE CATALOG
- DELETE DATAVOLS
- DELETE DUMPS
- DELETE MEDIA
- DELETE RESOURCEMANAGER
- DELETE TMF
- DELETE TRANSACTION
- DISABLE AUDITDUMP
- DISABLE BEGINTRANS
- DISABLE DATAVOLS
- DUMP FILES
- ENABLE AUDITDUMP
- ENABLE BEGINTRANS
- ENABLE DATAVOLS
- INFO ATDUMPDM
- INFO ATVOLUME
- INFO AUDITDUMP
- INFO AUDITTRAIL
- INFO BEGINTRANS
- INFO CATALOG
- INFO DATAVOLS
- INFO DUMPS
- INFO MEDIA
- INFO PROCESS
- INFO RESOURCEMANAGER
- INFO TMF
- LIST AUDITTRAIL
- NEXT AUDITTRAIL
- RECOVER FILES
- RELOCATE DISKDUMPS
- RESOLVE TRANSACTION
- START TMF
- STATUS ATFILE
- STATUS AUDITDUMP
- STATUS AUDITTRAIL
- STATUS BEGINTRANS
- STATUS CATALOG
- STATUS DATAVOLS
- STATUS OPERATION
- STATUS RESOURCEMANAGER
- STATUS RMTRANSBRANCHES
- STATUS TMF
- STATUS TMFSERVER
- STATUS TRANSACTION
- STATUS TRANSACTIONCHILDREN
- STOP TMF
- 6 Event Messages
- 7 Error and Warning Messages
- A TMF Configuration Limits and Defaults
- Index
Event Messages
HP NonStop TMF Management Programming Manual—540140-010
6-156
Descriptions of Event Messages
ZTMF-TKN-RCOV-Op-of-Error
specifies the operation that was being attempted. The values are:
ZTMF-VAL-RCOV-LOGICALREDO
ZTMF-VAL-RCOV-PHYSICALREDO
ZTMF-VAL-RCOV-LOGICALUNDO
ZTMF-VAL-RCOV-PHYSICALUNDO
ZTMF-VAL-RCOV-FLABMODREDO
ZTMF-VAL-RCOV-FLABMODUNDO
ZTMF-VAL-RCOV-CHANGEFLAB
ZTMF-VAL-RCOV-OPEN
ZTMF-VAL-RCOV-FLUSHFILES
ZTMF-VAL-RCOV-FLUSHAUDIT
ZTMF-VAL-RCOV-CLEARFLAGS
ZTMF-VAL-RCOV-READ
ZTMF-VAL-RCOV-POSITION
ZTMF-TKN-RCOV-Error-Index
contains an integer specifying an audit-trail index value (zero indicates the master
audit trail; one through 15 indicate auxiliary audit trails).
ZTMF-TKN-RCOV-Error-Sno
contains an integer specifying an audit-trail file sequence number.
ZTMF-TKN-RCOV-Error-Rba
contains an integer specifying a relative byte address (rba) within the audit-trail file.
If the rba is less than 2,147,483,647, this token contains the actual rba. If the rba is
2,147,483,647 or greater, this token contains 2,147,483,647 (and the RBA2 token
contains the actual rba).
ZTMF-TKN-RCOV-Error-Rba2
contains an integer specifying a relative byte address (rba) within the audit-trail file.
This token always contains the actual rba.
ZEMS-TKN-Emphasis
is set to False for this event.