TMF Management Programming Manual (H06.06+, J06.03+)
Table Of Contents
- HP NonStop TMF Management Programming Manual
- Legal Notices
- Contents
- What’s New in This Manual
- About This Manual
- 1 Introduction to TMF
- 2 Communicating With the TMFSERVE Process
- 3 SPI Programming Considerations for TMF
- 4 Common Definitions
- 5 Commands and Responses
- Command Summary
- Command Descriptions
- ABORT TRANSACTION
- ADD AUDITTRAIL
- ADD DATAVOLS
- ADD DUMPS
- ADD MEDIA
- ADD RESOURCEMANAGER
- ALTER AUDITDUMP
- ALTER AUDITTRAIL
- ALTER BEGINTRANS
- ALTER CATALOG
- ALTER DATAVOLS
- ALTER DUMPS
- ALTER MEDIA
- ALTER PROCESS
- ALTER TMF
- CANCEL OPERATION
- CLOSE RESOURCEMANAGER
- DELETE CATALOG
- DELETE DATAVOLS
- DELETE DUMPS
- DELETE MEDIA
- DELETE RESOURCEMANAGER
- DELETE TMF
- DELETE TRANSACTION
- DISABLE AUDITDUMP
- DISABLE BEGINTRANS
- DISABLE DATAVOLS
- DUMP FILES
- ENABLE AUDITDUMP
- ENABLE BEGINTRANS
- ENABLE DATAVOLS
- INFO ATDUMPDM
- INFO ATVOLUME
- INFO AUDITDUMP
- INFO AUDITTRAIL
- INFO BEGINTRANS
- INFO CATALOG
- INFO DATAVOLS
- INFO DUMPS
- INFO MEDIA
- INFO PROCESS
- INFO RESOURCEMANAGER
- INFO TMF
- LIST AUDITTRAIL
- NEXT AUDITTRAIL
- RECOVER FILES
- RELOCATE DISKDUMPS
- RESOLVE TRANSACTION
- START TMF
- STATUS ATFILE
- STATUS AUDITDUMP
- STATUS AUDITTRAIL
- STATUS BEGINTRANS
- STATUS CATALOG
- STATUS DATAVOLS
- STATUS OPERATION
- STATUS RESOURCEMANAGER
- STATUS RMTRANSBRANCHES
- STATUS TMF
- STATUS TMFSERVER
- STATUS TRANSACTION
- STATUS TRANSACTIONCHILDREN
- STOP TMF
- 6 Event Messages
- 7 Error and Warning Messages
- A TMF Configuration Limits and Defaults
- Index
Event Messages
HP NonStop TMF Management Programming Manual—540140-010
6-167
Descriptions of Event Messages
ZTMF-VAL-ARExcp-AuxPtrMismatch
ZTMF-VAL-ARExcp-Format2File
ZTMF-VAL-ARExcp-Format2Rec
ZEMS-TKN-Emphasis
is set to False for this event.
Effect
The recovery process abends.
In the case of volume recovery, the process is not restarted. The affected data volume
is flagged as needing recovery and is disabled for transaction processing.
In the case of backout or file recovery, the TMF management process (TMP) restarts
the process. If the error was transitory, the recovery operation continues to completion.
If the error persists, the recovery process abends again and is restarted. The restart
attempts occur at successively longer time intervals.
Recommended Action
If the audit read exception is ZTMF-VAL-ARExcp-Format2File or ZTMF-VAL-ARExcp-
Format2Rec, the current version of TMF supports only Format 1 audit trail files but the
recovery process encountered a Format 2 file or record. You should do either of the
following:
Delete TMF (which deletes all audit trail files, including the Format 2 file or record),
and restart the current version of TMF.
Upgrade to the G08V01 or a later version of the software, and retry the recovery.
For all other audit read exceptions, this is a serious event. If a data volume is disabled,
its unavailability could degrade the performance of one or more applications. If either
backout or file recovery is retried many times, audit-trail files could get pinned on the
disk, causing the audit trail to reach the overflow threshold.
Contact your service provider and provide all relevant information as follows:
Descriptions of the problem and accompanying symptoms
Details from the message(s) generated
Supporting documentation such as Event Management Service (EMS) logs, trace
files, and a CPU dump, if applicable
If your local operating procedures require contacting the Global Customer Support
Center (GCSC), supply your system number and the numbers and versions of all
related products as well.