TMF Management Programming Manual (H06.06+, J06.03+)
Table Of Contents
- HP NonStop TMF Management Programming Manual
- Legal Notices
- Contents
- What’s New in This Manual
- About This Manual
- 1 Introduction to TMF
- 2 Communicating With the TMFSERVE Process
- 3 SPI Programming Considerations for TMF
- 4 Common Definitions
- 5 Commands and Responses
- Command Summary
- Command Descriptions
- ABORT TRANSACTION
- ADD AUDITTRAIL
- ADD DATAVOLS
- ADD DUMPS
- ADD MEDIA
- ADD RESOURCEMANAGER
- ALTER AUDITDUMP
- ALTER AUDITTRAIL
- ALTER BEGINTRANS
- ALTER CATALOG
- ALTER DATAVOLS
- ALTER DUMPS
- ALTER MEDIA
- ALTER PROCESS
- ALTER TMF
- CANCEL OPERATION
- CLOSE RESOURCEMANAGER
- DELETE CATALOG
- DELETE DATAVOLS
- DELETE DUMPS
- DELETE MEDIA
- DELETE RESOURCEMANAGER
- DELETE TMF
- DELETE TRANSACTION
- DISABLE AUDITDUMP
- DISABLE BEGINTRANS
- DISABLE DATAVOLS
- DUMP FILES
- ENABLE AUDITDUMP
- ENABLE BEGINTRANS
- ENABLE DATAVOLS
- INFO ATDUMPDM
- INFO ATVOLUME
- INFO AUDITDUMP
- INFO AUDITTRAIL
- INFO BEGINTRANS
- INFO CATALOG
- INFO DATAVOLS
- INFO DUMPS
- INFO MEDIA
- INFO PROCESS
- INFO RESOURCEMANAGER
- INFO TMF
- LIST AUDITTRAIL
- NEXT AUDITTRAIL
- RECOVER FILES
- RELOCATE DISKDUMPS
- RESOLVE TRANSACTION
- START TMF
- STATUS ATFILE
- STATUS AUDITDUMP
- STATUS AUDITTRAIL
- STATUS BEGINTRANS
- STATUS CATALOG
- STATUS DATAVOLS
- STATUS OPERATION
- STATUS RESOURCEMANAGER
- STATUS RMTRANSBRANCHES
- STATUS TMF
- STATUS TMFSERVER
- STATUS TRANSACTION
- STATUS TRANSACTIONCHILDREN
- STOP TMF
- 6 Event Messages
- 7 Error and Warning Messages
- A TMF Configuration Limits and Defaults
- Index
Error and Warning Messages
HP NonStop TMF Management Programming Manual—540140-010
7-56
Archive Tape Errors and Warnings
8006 The DEVICE attribute of the tape ZART-TKN-DEFINENAME specifies a
drive, ZART-TKN-DEVICENAME, whose system either does not exist
or is inaccessible because all paths to it are down.
A tape drive was specified with a DEFINE whose system either does not exist or
is unavailable.
8007 The SYSTEM attribute of the tape DEFINE ZART-TKN-DEFINENAME
specifies a system, ZART-TKN-SYSTEMNAME, that is on a pre-C00
operating system.
A system was specified with a DEFINE that is not running a C00 or later RVU
of the operating system.
8008 The DEVICE attribute of the tape ZART-TKN-DEFINENAME specifies a
drive, ZART-TKN-DEVICENAME, whose system is on a pre-C00
operating system.
A tape drive was specified with a DEFINE whose system is not running a C00 or
later RVU of the operating system.
8009 The SYSTEM attribute of the tape DEFINE ZART-TKN-DEFINENAME
specifies a system, ZART-TKN-SYSTEMNAME, that does not have
labeled tape support configured.
A system was specified with a DEFINE that does not have labeled tape support
configured.
8010 The DEVICE attribute of the tape DEFINE ZART-TKN-DEFINENAME
specifies a drive, ZART-TKN-DEVICENAME, whose system does not
have labeled tape support configured.
A tape drive was specified with a DEFINE whose system does not have labeled
tape support configured.
8011 The tape DEFINE ZART-TKN-DEFINENAME specifies labeled tape
processing and labeled tape support is not configured.
The local system does not have labeled tape support configured.
8012 Duplicate volume ID found in the VOLUME attribute of the tape
DEFINE ZART-TKN-DEFINENAME.
The VOLUME attribute of the specified tape DEFINE clause contains a
duplicate volume name.