TMF Management Programming Manual (H06.06+, J06.03+)
Table Of Contents
- HP NonStop TMF Management Programming Manual
- Legal Notices
- Contents
- What’s New in This Manual
- About This Manual
- 1 Introduction to TMF
- 2 Communicating With the TMFSERVE Process
- 3 SPI Programming Considerations for TMF
- 4 Common Definitions
- 5 Commands and Responses
- Command Summary
- Command Descriptions
- ABORT TRANSACTION
- ADD AUDITTRAIL
- ADD DATAVOLS
- ADD DUMPS
- ADD MEDIA
- ADD RESOURCEMANAGER
- ALTER AUDITDUMP
- ALTER AUDITTRAIL
- ALTER BEGINTRANS
- ALTER CATALOG
- ALTER DATAVOLS
- ALTER DUMPS
- ALTER MEDIA
- ALTER PROCESS
- ALTER TMF
- CANCEL OPERATION
- CLOSE RESOURCEMANAGER
- DELETE CATALOG
- DELETE DATAVOLS
- DELETE DUMPS
- DELETE MEDIA
- DELETE RESOURCEMANAGER
- DELETE TMF
- DELETE TRANSACTION
- DISABLE AUDITDUMP
- DISABLE BEGINTRANS
- DISABLE DATAVOLS
- DUMP FILES
- ENABLE AUDITDUMP
- ENABLE BEGINTRANS
- ENABLE DATAVOLS
- INFO ATDUMPDM
- INFO ATVOLUME
- INFO AUDITDUMP
- INFO AUDITTRAIL
- INFO BEGINTRANS
- INFO CATALOG
- INFO DATAVOLS
- INFO DUMPS
- INFO MEDIA
- INFO PROCESS
- INFO RESOURCEMANAGER
- INFO TMF
- LIST AUDITTRAIL
- NEXT AUDITTRAIL
- RECOVER FILES
- RELOCATE DISKDUMPS
- RESOLVE TRANSACTION
- START TMF
- STATUS ATFILE
- STATUS AUDITDUMP
- STATUS AUDITTRAIL
- STATUS BEGINTRANS
- STATUS CATALOG
- STATUS DATAVOLS
- STATUS OPERATION
- STATUS RESOURCEMANAGER
- STATUS RMTRANSBRANCHES
- STATUS TMF
- STATUS TMFSERVER
- STATUS TRANSACTION
- STATUS TRANSACTIONCHILDREN
- STOP TMF
- 6 Event Messages
- 7 Error and Warning Messages
- A TMF Configuration Limits and Defaults
- Index
Error and Warning Messages
HP NonStop TMF Management Programming Manual—540140-010
7-57
Archive Tape Errors and Warnings
8013 Tape volume IDs for the two parallel copies are not different.
The tape volume IDs for two parallel copies specified in a tape DEFINE clause
are not unique.
8014 The attribute ZART-TKN-DEFINEATTRNAME was specified for the
tape DEFINE ZART-TKN-DEFINENAME and it is not allowed.
The specified attribute is not allowed in a tape DEFINE clause.
8015 VOLUME SCRATCH specified for input in the tape DEFINE ZART-
TKN-DEFINENAME.
VOLUME SCRATCH is not allowed as an input specification in a tape DEFINE
clause.
8016 Value for the tape DEFINE attribute DENSITY conflicts with the
DENSITY parameter.
An erroneous DENSITY attribute was specified in a tape DEFINE clause.
8025 Tape record is too short (Length: ZART-TKN-RECORDLEN).
The tape record is too short. This could be caused by corruption of the tape,
dirty tape drive heads, faulty tape drives, or a software bug in the dump or
restore program.
8026 Tape record is not even (Length: ZART-TKN-RECORDLEN).
The tape record is not even. This could be caused by corruption of the tape,
dirty tape drive heads, faulty tape drives, or a software bug in the dump or
restore program.
8027 Tape record checksum is bad.
The tape record checksum is invalid. This could be caused by corruption of the
tape, dirty tape drive heads, faulty tape drives, or a software bug in the dump or
restore program.
8028 Tape record type is unknown.
The tape record type is invalid. This could be caused by corruption of the tape,
dirty tape drive heads, faulty tape drives, or a software bug in the dump or
restore program.