TMF Management Programming Manual (H06.06+, J06.03+)
Table Of Contents
- HP NonStop TMF Management Programming Manual
- Legal Notices
- Contents
- What’s New in This Manual
- About This Manual
- 1 Introduction to TMF
- 2 Communicating With the TMFSERVE Process
- 3 SPI Programming Considerations for TMF
- 4 Common Definitions
- 5 Commands and Responses
- Command Summary
- Command Descriptions
- ABORT TRANSACTION
- ADD AUDITTRAIL
- ADD DATAVOLS
- ADD DUMPS
- ADD MEDIA
- ADD RESOURCEMANAGER
- ALTER AUDITDUMP
- ALTER AUDITTRAIL
- ALTER BEGINTRANS
- ALTER CATALOG
- ALTER DATAVOLS
- ALTER DUMPS
- ALTER MEDIA
- ALTER PROCESS
- ALTER TMF
- CANCEL OPERATION
- CLOSE RESOURCEMANAGER
- DELETE CATALOG
- DELETE DATAVOLS
- DELETE DUMPS
- DELETE MEDIA
- DELETE RESOURCEMANAGER
- DELETE TMF
- DELETE TRANSACTION
- DISABLE AUDITDUMP
- DISABLE BEGINTRANS
- DISABLE DATAVOLS
- DUMP FILES
- ENABLE AUDITDUMP
- ENABLE BEGINTRANS
- ENABLE DATAVOLS
- INFO ATDUMPDM
- INFO ATVOLUME
- INFO AUDITDUMP
- INFO AUDITTRAIL
- INFO BEGINTRANS
- INFO CATALOG
- INFO DATAVOLS
- INFO DUMPS
- INFO MEDIA
- INFO PROCESS
- INFO RESOURCEMANAGER
- INFO TMF
- LIST AUDITTRAIL
- NEXT AUDITTRAIL
- RECOVER FILES
- RELOCATE DISKDUMPS
- RESOLVE TRANSACTION
- START TMF
- STATUS ATFILE
- STATUS AUDITDUMP
- STATUS AUDITTRAIL
- STATUS BEGINTRANS
- STATUS CATALOG
- STATUS DATAVOLS
- STATUS OPERATION
- STATUS RESOURCEMANAGER
- STATUS RMTRANSBRANCHES
- STATUS TMF
- STATUS TMFSERVER
- STATUS TRANSACTION
- STATUS TRANSACTIONCHILDREN
- STOP TMF
- 6 Event Messages
- 7 Error and Warning Messages
- A TMF Configuration Limits and Defaults
- Index
Error and Warning Messages
HP NonStop TMF Management Programming Manual—540140-010
7-67
Dump/Restore Errors and Warnings
9006 Unable to write SQL label group due to file-system error ZTMF-TKN-
DR-FILEERROR.
A file-system error occurred while an online restore process was attempting to
write the NonStop SQL/MP label group into a disk directory.
The ZEMS-TKN-EMPHASIS token is set to TRUE.
9007 A good copy of tape # ZTMF-TKN-DR-TAPELNUM was not found for
dump serial ZTMF-TKN-DR-DUMPSERIALNUM in the TMF Catalog.
A restore process was attempting to read an audit dump or online dump and
found that the TMF catalog did not have a copy available for one of the tapes in
the tape set.
The ZEMS-TKN-EMPHASIS token is set to TRUE.
9008 Parity error occurred on tape file label.
A parity error occurred in a tape file label.
The ZEMS-TKN-EMPHASIS token is set to TRUE.
9009 Checksum error occurred on tape file label.
The checksum of a tape file label was invalid.
The ZEMS-TKN-EMPHASIS token is set to TRUE.
9010 Previous error affected the entire disk volume -- skipping the rest of
it.
This message indicates that the preceding error listed in the EMS log caused
the file to be aborted and thereby affected the entire volume. For example, file-
system error 66 (“Device is down”) is an error that affects the entire volume.
The ZEMS-TKN-EMPHASIS token is set to TRUE.
9011 The tape has the wrong Archive tape version (Expected version
name: ZTMF-TKN-DR-EXPECTEDTAPEVERNAME, actual version
name: ZTMF-TKN-DR-ARCHTAPEVERNAME). The TMF Catalog has
incorrect information.
A tape specified by the TMF catalog had the wrong archive tape version. This
could have been caused by an erroneous ADD DUMPS command.
The ZEMS-TKN-EMPHASIS token is set to TRUE.