TMF Management Programming Manual (H06.06+, J06.03+)
Table Of Contents
- HP NonStop TMF Management Programming Manual
- Legal Notices
- Contents
- What’s New in This Manual
- About This Manual
- 1 Introduction to TMF
- 2 Communicating With the TMFSERVE Process
- 3 SPI Programming Considerations for TMF
- 4 Common Definitions
- 5 Commands and Responses
- Command Summary
- Command Descriptions
- ABORT TRANSACTION
- ADD AUDITTRAIL
- ADD DATAVOLS
- ADD DUMPS
- ADD MEDIA
- ADD RESOURCEMANAGER
- ALTER AUDITDUMP
- ALTER AUDITTRAIL
- ALTER BEGINTRANS
- ALTER CATALOG
- ALTER DATAVOLS
- ALTER DUMPS
- ALTER MEDIA
- ALTER PROCESS
- ALTER TMF
- CANCEL OPERATION
- CLOSE RESOURCEMANAGER
- DELETE CATALOG
- DELETE DATAVOLS
- DELETE DUMPS
- DELETE MEDIA
- DELETE RESOURCEMANAGER
- DELETE TMF
- DELETE TRANSACTION
- DISABLE AUDITDUMP
- DISABLE BEGINTRANS
- DISABLE DATAVOLS
- DUMP FILES
- ENABLE AUDITDUMP
- ENABLE BEGINTRANS
- ENABLE DATAVOLS
- INFO ATDUMPDM
- INFO ATVOLUME
- INFO AUDITDUMP
- INFO AUDITTRAIL
- INFO BEGINTRANS
- INFO CATALOG
- INFO DATAVOLS
- INFO DUMPS
- INFO MEDIA
- INFO PROCESS
- INFO RESOURCEMANAGER
- INFO TMF
- LIST AUDITTRAIL
- NEXT AUDITTRAIL
- RECOVER FILES
- RELOCATE DISKDUMPS
- RESOLVE TRANSACTION
- START TMF
- STATUS ATFILE
- STATUS AUDITDUMP
- STATUS AUDITTRAIL
- STATUS BEGINTRANS
- STATUS CATALOG
- STATUS DATAVOLS
- STATUS OPERATION
- STATUS RESOURCEMANAGER
- STATUS RMTRANSBRANCHES
- STATUS TMF
- STATUS TMFSERVER
- STATUS TRANSACTION
- STATUS TRANSACTIONCHILDREN
- STOP TMF
- 6 Event Messages
- 7 Error and Warning Messages
- A TMF Configuration Limits and Defaults
- Index
Error and Warning Messages
HP NonStop TMF Management Programming Manual—540140-010
7-71
Dump/Restore Errors and Warnings
9030 File-system error ZTMF-TKN-DR-FILEERROR occurred on file.
ZTMF-TKN-DR-FILENAME.
A file-system error occurred for the specified file.
The ZEMS-TKN-EMPHASIS token is set to TRUE.
9031 Operator requested termination.
The operator requested the termination of a dump or restore operation.
The ZEMS-TKN-EMPHASIS token is set to TRUE.
9032 File-system error ZTMF-TKN-DR-FILEERROR from the TMF Catalog.
A dump or restore process encountered a file-system error from the TMF
catalog.
The ZEMS-TKN-EMPHASIS token is set to TRUE.
9033 NonStop SQL error ZTMF-TKN-DR-FILEERROR occurred on file
ZTMF-TKN-DR-FILENAME.
An online dump or restore process received a file-system error from NonStop
SQL/MP.
The ZEMS-TKN-EMPHASIS token is set to TRUE.
9034 Requested tape BLOCKSIZE not supported; using 28KB instead.
If a tape device cannot handle the larger blocksize when requested, blocksize
28KB is used for the dump. A warning message is generated to the EMS
subsystem indicating this condition. For online dumps, the same warning
message is generated to the TMFCOM DUMP FILES command display.
The ZEMS-TKN-EMPHASIS token is set to TRUE.
9035 This tape was created with a BLOCKSIZE larger than 28KB, but this
drive does not support large transfers.
This message is displayed for online restores and audit restores if a
tape was dumped with a blocksize larger than 28KB and the tape
drive does not support large block transfers.
The ZEMS-TKN-EMPHASIS token is set to TRUE.