TMF Management Programming Manual (H06.06+, J06.03+)
Table Of Contents
- HP NonStop TMF Management Programming Manual
- Legal Notices
- Contents
- What’s New in This Manual
- About This Manual
- 1 Introduction to TMF
- 2 Communicating With the TMFSERVE Process
- 3 SPI Programming Considerations for TMF
- 4 Common Definitions
- 5 Commands and Responses
- Command Summary
- Command Descriptions
- ABORT TRANSACTION
- ADD AUDITTRAIL
- ADD DATAVOLS
- ADD DUMPS
- ADD MEDIA
- ADD RESOURCEMANAGER
- ALTER AUDITDUMP
- ALTER AUDITTRAIL
- ALTER BEGINTRANS
- ALTER CATALOG
- ALTER DATAVOLS
- ALTER DUMPS
- ALTER MEDIA
- ALTER PROCESS
- ALTER TMF
- CANCEL OPERATION
- CLOSE RESOURCEMANAGER
- DELETE CATALOG
- DELETE DATAVOLS
- DELETE DUMPS
- DELETE MEDIA
- DELETE RESOURCEMANAGER
- DELETE TMF
- DELETE TRANSACTION
- DISABLE AUDITDUMP
- DISABLE BEGINTRANS
- DISABLE DATAVOLS
- DUMP FILES
- ENABLE AUDITDUMP
- ENABLE BEGINTRANS
- ENABLE DATAVOLS
- INFO ATDUMPDM
- INFO ATVOLUME
- INFO AUDITDUMP
- INFO AUDITTRAIL
- INFO BEGINTRANS
- INFO CATALOG
- INFO DATAVOLS
- INFO DUMPS
- INFO MEDIA
- INFO PROCESS
- INFO RESOURCEMANAGER
- INFO TMF
- LIST AUDITTRAIL
- NEXT AUDITTRAIL
- RECOVER FILES
- RELOCATE DISKDUMPS
- RESOLVE TRANSACTION
- START TMF
- STATUS ATFILE
- STATUS AUDITDUMP
- STATUS AUDITTRAIL
- STATUS BEGINTRANS
- STATUS CATALOG
- STATUS DATAVOLS
- STATUS OPERATION
- STATUS RESOURCEMANAGER
- STATUS RMTRANSBRANCHES
- STATUS TMF
- STATUS TMFSERVER
- STATUS TRANSACTION
- STATUS TRANSACTIONCHILDREN
- STOP TMF
- 6 Event Messages
- 7 Error and Warning Messages
- A TMF Configuration Limits and Defaults
- Index
Commands and Responses
HP NonStop TMF Management Programming Manual—540140-010
5-18
ADD DUMPS
Tokens in Command Buffer
ZTMF-TKN-FileName
specifies the audit trail file to be added to the catalog. This token is required;
multiple occurrences are allowed.
ZTMF-TKN-Media
for dumps to tape, specifies the name of the tape volume on which the dump is
stored. Specify the identifier magnetically encoded in the tape volume label and
registered in the TMF catalog. Either ZTMF-TKN-Media or ZTMF-TKN-DiskMedia
is required; multiple occurrences are allowed.
ZTMF-TKN-DiskMedia
for dumps to disk, specifies the disk volume on which the dump is located. Either
ZTMF-TKN-Media or ZTMF-TKN-DiskMedia is required; multiple occurrences are
allowed.
ZTMF-MAP-Add-Dumps
is an extensible structured token specifying the attributes of the dumps to be added
to the TMF catalog. This token is required; only one occurrence is allowed. This
token contains the following fields:
ZSerial
specifies the dump serial number of the online dump to be added to the TMF
catalog. The value should be the serial number of the original online dump.
This field is required; you must specify a value greater than or equal to 64.
ZDumpType
specifies the type of dump to be added to the TMF catalog. This field is
required. The following values are valid:
ZMasterSequence
specifies the master audit trail sequence number that was active when the
dump was made. This field is required if the value of ZDumpType is ZTMF-
VAL-OnlineDump.
ZTMF-VAL-AuditDump The dump is an audit dump.
ZTMF-VAL-OnlineDump The dump is an online dump.