TMF Management Programming Manual (H06.06+, J06.03+)
Table Of Contents
- HP NonStop TMF Management Programming Manual
- Legal Notices
- Contents
- What’s New in This Manual
- About This Manual
- 1 Introduction to TMF
- 2 Communicating With the TMFSERVE Process
- 3 SPI Programming Considerations for TMF
- 4 Common Definitions
- 5 Commands and Responses
- Command Summary
- Command Descriptions
- ABORT TRANSACTION
- ADD AUDITTRAIL
- ADD DATAVOLS
- ADD DUMPS
- ADD MEDIA
- ADD RESOURCEMANAGER
- ALTER AUDITDUMP
- ALTER AUDITTRAIL
- ALTER BEGINTRANS
- ALTER CATALOG
- ALTER DATAVOLS
- ALTER DUMPS
- ALTER MEDIA
- ALTER PROCESS
- ALTER TMF
- CANCEL OPERATION
- CLOSE RESOURCEMANAGER
- DELETE CATALOG
- DELETE DATAVOLS
- DELETE DUMPS
- DELETE MEDIA
- DELETE RESOURCEMANAGER
- DELETE TMF
- DELETE TRANSACTION
- DISABLE AUDITDUMP
- DISABLE BEGINTRANS
- DISABLE DATAVOLS
- DUMP FILES
- ENABLE AUDITDUMP
- ENABLE BEGINTRANS
- ENABLE DATAVOLS
- INFO ATDUMPDM
- INFO ATVOLUME
- INFO AUDITDUMP
- INFO AUDITTRAIL
- INFO BEGINTRANS
- INFO CATALOG
- INFO DATAVOLS
- INFO DUMPS
- INFO MEDIA
- INFO PROCESS
- INFO RESOURCEMANAGER
- INFO TMF
- LIST AUDITTRAIL
- NEXT AUDITTRAIL
- RECOVER FILES
- RELOCATE DISKDUMPS
- RESOLVE TRANSACTION
- START TMF
- STATUS ATFILE
- STATUS AUDITDUMP
- STATUS AUDITTRAIL
- STATUS BEGINTRANS
- STATUS CATALOG
- STATUS DATAVOLS
- STATUS OPERATION
- STATUS RESOURCEMANAGER
- STATUS RMTRANSBRANCHES
- STATUS TMF
- STATUS TMFSERVER
- STATUS TRANSACTION
- STATUS TRANSACTIONCHILDREN
- STOP TMF
- 6 Event Messages
- 7 Error and Warning Messages
- A TMF Configuration Limits and Defaults
- Index
Commands and Responses
HP NonStop TMF Management Programming Manual—540140-010
5-22
ADD MEDIA
ZTMF-VAL-Scratch
specifies that the tape volume can be used for dumping files.
ZDensity
specifies the density at which the tapes are written. This field is only valid if
ZLabelMedia is ZSPI-VAL-True. The following values are valid:
ZTapeMode
specifies the kind of write operation performed by the tape drive and is
applicable only for streaming tape drives. This field is only valid if ZLabelMedia
is ZSPI-VAL-True. The following values are valid:
ZTMF-VAL-StartStop
ZTMF-VAL-Stream
ZTMF-VAL-StreamSlow
ZTMF-VAL-StreamFast
If this field is null, the default value depends upon the tape drive. You can
specify either ZDensity or ZTapeMode, but not both in the same command.
ZTapeDrive
specifies the name of the tape drive on which you want to label tape volumes.
Guardian labeled-tape processing must be enabled on the node (system) you
specify. This field is required if the value of ZLabelMedia is ZSPI-VAL-True.
ZOperatorDevice
specifies the name of the device on which TAPECOM prompts are to be
displayed. This field is required if the value of ZLabelMedia is ZSPI-VAL-True.
Usage Guidelines
Only super-group users can issue this command.
For more information on the ADD TAPEMEDIA command, see the TMF Reference
Manual.
ZTMF-VAL-Default If this field is null, the default value depends
upon the tape drive.
ZTMF-VAL-800BPI The density is 800 bits per inch.
ZTMF-VAL-1600BPI The density is 1600 bits per inch.
ZTMF-VAL-6250BPI The density is 6250 bits per inch.