Cluster I/O Protocols (CIP) Configuration and Management Manual (H06.16+, J06.05+)

N1002541.eth3 UP UP N1002582.eth3 UP UP N1002541.eth3 Home
N1002541.eth2 UP UP -- -- N1002541.eth2 --
N1002541.eth1 UP UP -- -- N1002541.eth1 --
N1002582.bond0, N1002582.bond1 and N1002582.eth3 have a status of UP, show Home
in the Fovr field and show themselves as the current interfaces in the Current field. They
have been restored to the default.
You have now completed the procedure for upgrading an IP CLIM. Continue upgrade operations
until all IP CLIMs are upgraded.
Upgrading IB and Telco CLIMs
CAUTION: During this procedure, the Telco CLIM loses connectivity.
For Telco CLIMs, redundancy is configured at the application level. Multiple links using different
CLIMs are configured to each destination and traffic is load balanced across all active links to that
destination. There is no failover for Telco CLIMs, just a redistribution of load across the link-set
going to a common destination.
CAUTION: Determine the configuration for all links on all the Telco CLIMs. Make sure that all the
links on the CLIM being upgraded have a companion link to the same destination on another CLIM
and that all those links are displaying a healthy status before performing the upgrade.
NOTE: IB CLIMs are similar to Telco CLIMs although they do not have the CCMI tool. Use the
procedure for Telco CLIMs for upgrading IB CLIMs.
1. Prepare the Telco CLIM for Upgrade (skip if the host system is not running)
a. List the CLIMs:
> SCF
> INFO CLIM $ZZCIP.*
Name Mode Location ConnPts Provider
N1002541 IP (100 ,2 ,5 ,4 ,1 ) 1 CSAM2
N1002542 IP (100 ,2 ,5 ,4 ,2 ) 1 ZTC0
N1002581 IP (100 ,2 ,5 ,8 ,1 ) 1 ZTC0
N1002582 IP (100 ,2 ,5 ,8 ,2 ) 1 CSAM2
N1012581 IP (101 ,2 ,5 ,8 ,1 ) 1 CSAM5
N1012582 IP (101 ,2 ,5 ,8 ,2 ) 1 CSAM5
O1002571 OPEN (100 ,2 ,5 ,7 ,1 ) 1 CSAM3
O1002572 OPEN (100 ,2 ,5 ,7 ,2 ) 1 CSAM4
S1002531 STORAGE (100 ,2 ,5 ,3 ,1 ) 2 --
S1002533 STORAGE (100 ,2 ,5 ,3 ,3 ) 2 --
There are two Open/Telco CLIMs (O1002571 and O1002572), configured in Providers
CSAM3 and CSAM4.
b. Examine the linkset configuration by generating a configuration report with the HP OpenCall
INS Command Control and Monitoring Interface (CCMI). The Guide to Operations and
Maintenance for HP OpenCall Intelligent Network Serve describes the Configuration Report
generated from the System Home Page (used to get to CCMI) and the instructions for generating
the report are in the online help.
c. Ensure all Telco CLIMs are in the STARTED state.
> STATUS CLIM $ZZCIP.O*
CIP Status CLIM
Name Present State Trace
O1002571 Yes STARTED OFF
O1002572 Yes STARTED OFF
d. Determine which Telco CLIMs are configured as multi-link by using CCMI. See the Guide to
Operations and Maintenance for HP OpenCall Intelligent Network Server.
Upgrading CLIM Software and Firmware While Maintaining Network or Storage Traffic 145