RDF System Management Manual for J-series and H-series RVUs (RDF 1.10)

Security Restrictions
None; anyone can enter a STATUS command.
RDF State Requirement
You can enter a STATUS command at any time after RDF has been initialized.
Usage Guidelines
The STATUS command provides you with the most current information about RDF and its operational
status, presenting data for the specified RDF processes.
STATUS RDF Command Output Display
The output of the STATUS RDF command shows all critical information about each configured RDF
entity. Here are two examples:
RDFCOM - T0346H09 – 11AUG08
(C)2008 Hewlett-Packard Development Company, L.P.
Status of \RDF04 -> \RDF05 RDF 2008/08/11 05:26:49.082
Control Subvol: $SYSTEM.RDF04
Current State : Normal
RDF Process Name RTD Time Pri Volume Seqnce Rel Byte Addr Cpus Err
------------------ ------ --------- --- ------- ------ ------------- ----- ----
Monitor $RMON 185 $AUDMAT 56 1: 2
Extractor (0) $REXT0 0:00 185 $AUDMAT 56 928000 1: 2
Extractor (1) $REXT1 0:00 185 $AUDAUX 4 10435580 1: 2
Receiver (0) $RRCV0 0:00 185 $MIT 12 1: 2
Receiver (1) $RRCV1 0:00 185 1: 2
Imagetrail (0) $IMAGE0 22
Imagetrail (1) $IMAGEA 3
Purger $RPRG 185 1: 2
$DATA06 -> $DATA06 $RUPD1 0:06 185 $IMAGE0 22 9568 1: 2
$DATA07 -> $DATA07 $RUPD2 0:00 185 $IMAGEA 3 811008 2: 3
$DATA08 -> $DATA08 $RUPD3 0:06 185 $IMAGEA 3 811568 3: 0
RDFCOM - T0346H09 – 11AUG08
C)2008 Hewlett-Packard Development Company, L.P.
Status of \RDF04 -> \RDF05 RDF 2008/08/11 05:26:49.082
Control Subvol: $SYSTEM.RDF04
Current State : * TAKEOVER in progress *
RDF Process Name RTD Time Pri Volume Seqnce Rel Byte Addr Cpus Err
------------------ ------ --------- --- ------- ------ ------------- ----- ----
Monitor $Z345 ......... ... 2: 3
Receiver (0) $RRCV0 ......... 185 $MIT 12 1: 2
Receiver (1) $RRCV1 ......... 185 1: 2
Imagetrail (0) $IMAGE0 22
Imagetrail (1) $IMAGEA 3
Purger $RPRG 185 1: 2
$DATA06 -> $DATA06 $RUPD1 ......... 185 $IMAGE0 20 9568 1: 2 net
$DATA07 -> $DATA07 $RUPD2 ......... 185 $IMAGEA 3 811008 2: 3 undo
$DATA08 -> $DATA08 $RUPD3 ......... 185 $IMAGEA 3 811568 3: 0 undo
In each of these examples, the first line shows the RDF banner that includes the Product Version
Number and the date of its release (T0346A08 - 11AUG08). The second line contains the standard
Hewlett-Packard banner. The status information about the specific RDF subsystem begins on the
third line, where the names of the primary (\RDF04) and backup (\RDF05) systems are given,
followed by the timestamp when this instance of the STATUS RDF command was issued.
The control subvolume is listed next line, and the following line lists the current state of the RDF
subsystem. In the first example, the state is NORMAL (RDF running with Update On), and the
second example the state indicates that an RDF takeover operation has begun. The following list
234 Entering RDFCOM Commands