H06.05 Software Installation and Upgrade Guide Abstract This manual provides detailed procedures for installing H06.05 software on an HP Integrity NonStop NS-series server. Product Version N.A. Supported Release Version Updates (RVUs) This manual supports the H06.05 RVU only.
Document History Part Number Product Version 541762-003 NA Published March 2006
H06.05 Software Installation and Upgrade Guide Glossary Index What’s New in This Manual ix Manual Information ix New and Changed Information Tables ix About This Manual xi Who Should Use This Guide xi What This Guide Does Not Cover xi How This Guide Relates to Other Manuals Notation Conventions xii xii 1. Overview of Installing the H06.05 RVU Disk Space Requirements 1-1 Operational Differences Between the H06.
1. Overview of Installing the H06.05 RVU (continued) Contents 1. Overview of Installing the H06.05 RVU (continued) H06.05 Installation, Migration, and Fallback Considerations 1-22 Kernel-Managed Swap File (KMSF) 1-22 IOAM and Migrating Existing Data to an Enterprise Storage System ( ESS) NonStop SQL/MX 1-23 OSS 1-24 Minimum Memory Requirements 1-25 PSTATE (T0705H01) and WHOHAS (T0706H01) 1-25 SANMAN and SNETMON 1-25 Remote Database Facility (RDF) 1-26 HP Tandem Failure Data System (TFDS) 1-26 TMF 3.
4. Installing a SUT for the H06.05 RVU Contents Verify System Processes (continued) Verify Firmware 3-7 Verify Critical System Processes 3-7 Verify Disk Drives 3-8 Verify Tape Drives (If Necessary) 3-8 Check the Status of the Spooler Collector 3-9 Check for Sufficient Swap File Space 3-9 Install Node Interoperability SPRs 3-10 3-11 4. Installing a SUT for the H06.
7. Resuming Normal Operations Contents 7. Resuming Normal Operations Start User and System Applications 7-1 Before Starting DSM/SCM 7-1 Start DSM/SCM 7-2 Configure Specific Products (Post-System Load) 7-2 Update NonStop TCP/IP Configuration Files 7-3 Configure OSS 7-5 Configure SMF (Optional) 7-6 Configure the Remote Database Facility (RDF) 7-7 Configure the WAN Manager 7-7 8.
A. Using DSM/SCM to Install SPRs Contents A.
Contents B. Installing SWID, DSM/SCM PVU, and Planner Interface (PI) Client Software (continued) B.
Tables (continued) Contents Tables (continued) Table 1-5. Table 1-6. Table 1-7. Table 2-1. Table 2-2. Table 3-1. Table 6-1. Updateable Firmware for ServerNet WAN (SWAN and SWAN 2) Concentrators 1-21 Updateable Firmware for the NonStop ServerNet Switch 1-21 Tasks and Tools for Backing Out to the Previous SYSnn 1-31 H06.05 Upgrade Checklist 2-1 H06.05 Required Information Checklist 2-3 Interoperability SPRs for NonStop NS-Series and NonStop S-Series Systems 3-10 System Load Paths in Order of Use 6-1 H06.
Contents H06.
What’s New in This Manual Manual Information H06.05 Software Installation and Upgrade Guide Abstract This manual provides detailed procedures for installing H06.05 software on an HP Integrity NonStop NS-series server. Product Version N.A. Supported Release Version Updates (RVUs) This manual supports the H06.05 RVU only.
What’s New in This Manual New and Changed Information H06.
About This Manual This guide describes: • • Upgrading the initial H06.05 RVU through the use of site update tape (SUT) refreshes, if necessary. Falling back to a previous SYSnn.
How This Guide Relates to Other Manuals About This Manual How This Guide Relates to Other Manuals • • • • • • • • • The NonStop System Console Installer Guide contains information on installing OSM client-based components, and other applications on system consoles. The H06.05 Release Version Update Compendium provides summary information on the new features and migration issues for H06.05. The OutsideView online help provides information on configuring OutsideView sessions.
General Syntax Notation About This Manual UPPERCASE LETTERS. Uppercase letters indicate keywords and reserved words. Type these items exactly as shown. Items not enclosed in brackets are required. For example: MAXATTACH lowercase italic letters. Lowercase italic letters indicate variable items that you supply. Items not enclosed in brackets are required. For example: file-name computer type. Computer type letters within text indicate C and Open System Services (OSS) keywords and reserved words.
Notation for Messages About This Manual … Ellipsis. An ellipsis immediately following a pair of brackets or braces indicates that you can repeat the enclosed sequence of syntax items any number of times. For example: M address [ , new-value ]… [ - ] {0|1|2|3|4|5|6|7|8|9}… An ellipsis immediately following a single syntax item indicates that you can repeat that syntax item any number of times. For example: "s-char…" Punctuation.
Notation for Messages About This Manual Nonitalic text. Nonitalic letters, numbers, and punctuation indicate text that is displayed or returned exactly as shown. For example: Backup Up. lowercase italic letters. Lowercase italic letters indicate variable items whose values are displayed or returned. For example: p-register process-name [ ] Brackets. Brackets enclose items that are sometimes, but not always, displayed.
Notation for Management Programming Interfaces About This Manual Notation for Management Programming Interfaces This list summarizes the notation conventions used in the boxed descriptions of programmatic commands, event messages, and error lists in this manual. UPPERCASE LETTERS. Uppercase letters indicate names from definition files. Type these names exactly as shown. For example: ZCOM-TKN-SUBJ-SERV lowercase letters.
1 Overview of Installing the H06.05 RVU This section introduces the basic installation tools and requirements in H-series RVUs, including installing the site update tape (SUT) for an release version update revision (RVUR). For information on installing software product revisions (SPRs), see Appendix A, Using DSM/SCM to Install SPRs.
Overview of Installing the H06.05 RVU Investigating an H-Series RVU For a complete list of supported tape drives, including using SCSI to connect to G-series legacy tape drives, see the NonStop NS-Series Planning Guide and the NonStop NS-Series Supported Hardware document in NTL. • • • • • • Compaq TSM is not supported in H-series RVUs. You must use OSM. For many update tasks, you can still use the Subsystem Control Facility (SCF).
Overview of Installing the H06.05 RVU • • • System Console Requirements The Managing Software Changes manual explains TRM2000 and provides information about system migration and installation processes, software product revision (SPR) analysis, and resources for investigating new RVUs and SPRs. Scout for NonStop Servers is a Web-based SPR analysis and delivery tool. You can access Scout through HP NonStop eServices Portal at https://onepoint.nonstop.compaq.com/buildpage.asp.
Overview of Installing the H06.05 RVU Using OSM With the H06.05 RVU Using OSM With the H06.05 RVU OSM Server-Based Components For H06.05, the server-based OSM SPR is T0682 H02^AAN. Highlights for OSM support of Integrity NonStop NS-series servers include: • • • Guided procedures for replacing processor switch and IOAM components. OSM also provides documented service procedures for replacing Fibre Channel disk module (FCDM), NonStop Blade Element, and LSU components.
Overview of Installing the H06.05 RVU • • • • Using DSM/SCM With the H06.05 RVU A new System Load dialog box, unique to NS-series systems, provides the ability to: ° Load the system from alternate system load configurations (using either SCSI or FC disks) created through the OSM Service Connection. After a configuration is saved, you can load the system using mirrored disks without reviving.
Overview of Installing the H06.05 RVU • • • • DSM/SCM and Public DLLs Creating a SIT is not supported in H-series RVUs. Similar to G-series RVUs, you might have to update both the client and server-side SPRs. For H06.05, the PI screen displays G02/H02 for the client side and H02 for the server side. As of G06.27, you can manage an H-series target system from a G-series host system. However, you cannot currently manage a G-series target system from an H-series host.
Overview of Installing the H06.05 RVU Summary of Software Installation Tasks Summary of Software Installation Tasks To install software using DSM/SCM, perform these tasks: 1. Receive new software into the DSM/SCM Archive. When software is received, the files from each product are stored in the DSM/SCM Archive, a holding area for your software. File attributes are stored in the DSM/SCM host database.
Overview of Installing the H06.05 RVU Check or Alter the CONFTEXT File Before Installing an H06.05 SUT ZMODGP is a TACL script that makes changes to the generic-process definitions in the system configuration database. When you use the ZMODGP script, you do not need to hard code new generic process definitions directly into the $ZCDB process (T6586, Configuration Services). Check or Alter the CONFTEXT File Before Installing an H06.
Overview of Installing the H06.05 RVU Managing Maintenance Entity Firmware for Processor Switch and I/O Adapter Module (IOAM) wide range of system problems, from intermittent faults to partial or complete system outages. Note. Always check Scout for the most recent updateable firmware. Although OSM does display firmware revision information (Downrev, Same, or Uprev), you can enter the FILEINFO command to see firmware files using the FILEINFO command.
Managing Maintenance Entity Firmware for Processor Switch and I/O Adapter Module (IOAM) Overview of Installing the H06.05 RVU Updating ME Firmware Table 1-1 shows the current ME firmware information for both processor switches and IOAMS: Table 1-1.
Managing Maintenance Entity Firmware for Processor Switch and I/O Adapter Module (IOAM) Overview of Installing the H06.05 RVU You should not use the Multi-Resource Actions dialog (in the OSM Service Connection) to update ME firmware or ME FPGA simultaneously on both fabrics, or a system outage might occur. Updating ME FPGA Table 1-2 shows the current ME FPGA information for both processor switches and IOAMs: Table 1-2.
Managing Firmware in a NonStop Blade Complex Overview of Installing the H06.05 RVU Managing Firmware in a NonStop Blade Complex Note. In TACL commands and event messages, you might see: • • The term slice, which is equivalent to the term NonStop Blade Element (NSBE). The term processor complex, which is equivalent to the term NonStop Blade Complex (NSBC) .The OSM GUI now displays the newer Blade Complex and Blade Element terminology.
Managing Firmware in a NonStop Blade Complex Overview of Installing the H06.05 RVU For more information on the NonStop advanced architecture (NSAA), see the NonStop NS-Series Planning Guide. Updating processor boot code is part of the Halted State Services (HSS) firmware, which consists of HSS Main, Primitive State code (pState), SCSI firmware (ISP1040), bootstrap (Diskboot), Baseboard Management Controller (BMC) firmware, and PAL/SAL firmware (IPF Firmware.
Managing Firmware in a NonStop Blade Complex Overview of Installing the H06.05 RVU Table 1-3. HP Integrity NonStop NS-Series Server Firmware (page 2 of 2) Module Filename Notes Primitive State Firmware T0287H01 PRMFIRMW Primitive state firmware ISP1040 firmware T0480H01 ISPFIRMW ISP1040 firmware is controller firmware for legacy I/O or SCSI disks in G-series RVUs Baseboard Management Controller Firmware (BMC) T0661 M0661 BMC firmware is used for board and module maintenance.
Overview of Installing the H06.05 RVU Managing Firmware in a NonStop Blade Complex firmware update procedure, check for any yellow or red alarms associated with a processor (blade) complex. These alarms might indicate a severe problem. You can, however, begin the firmware update if the yellow alarm is associated with a downrev firmware file.
Overview of Installing the H06.05 RVU Managing Firmware in a NonStop Blade Complex 2. From the shortcut menu, select Actions. 3. When the Actions window appears, select Firmware Update from the Available Actions list. 4. Click Perform action. 5. In the guided procedures interface, click Start in the Procedure Tasks List pane. 6. Follow and complete the guided procedure dialog boxes using this summary: a. Update NonStop Blade Complex (NSBC) firmware: 1.
Overview of Installing the H06.05 RVU Managing ServerNet Adapter Firmware 3. Load (coldload) the system with the H06.05 RVU. c. Update NonStop Blade Complex (NSBC) firmware on the other flash, as follows: 1. Using the OSM Service Connection and the Blade Complex Firmware Update guided procedure, complete the dialog boxes and update the shadow firmware on each NonStop Blade Element. Note. OSM will preselect all the firmware that it detects as down-rev. Note.
Overview of Installing the H06.05 RVU Managing ServerNet Adapter Firmware VST013.vsd • FCSA. The FCSA has two ports that allow connection to external, fibre-channelenabled devices. You might need to update these firmware files using either SCF or OSM. ° The flash boot firmware (T0630G06) contains version information about the boot firmware located in the FCSA FLASH memory.
Overview of Installing the H06.05 RVU Managing ServerNet Adapter Firmware VST018.vsd • G4SA. The OSM Service Connection displays G4SA firmware attributes and action under the G4SA SAC object. To check or update G4SA firmware, locate and expand the G4SA, then select its subcomponent G4SA SAC object. In the following example, the firmware attributes show that the current firmware Version is the same as the available Default File Version; no update is necessary.
Managing SWAN and SWAN 2 Concentrator Firmware Overview of Installing the H06.05 RVU Table 1-4.
Managing NonStop Cluster Switch Firmware Overview of Installing the H06.05 RVU Table 1-5.
Overview of Installing the H06.05 RVU H06.05 Installation, Migration, and Fallback Considerations H06.05 Installation, Migration, and Fallback Considerations See the Readme file and the appropriate softdocs for the latest information on any migration or configuration steps. Kernel-Managed Swap File (KMSF) Integrity NonStop NS-series servers require more swap space than do NonStop S-series servers. The default is 512 megabytes for each processor.
Overview of Installing the H06.05 RVU NonStop SQL/MX The FCHECK utility (introduced in G06.24) includes a migration option that reports the files that cannot be migrated to ESS because of this format limitation, in addition to reporting the amount of disk space required for check block protection. NonStop SQL/MX NonStop SQL/MX Release 2.
Overview of Installing the H06.05 RVU OSS OSS See the Open System Services Management and Operations Guide and the Open System Services Installation Guide for information about updating and maintaining OSS database files. See the Interactive Upgrade Guide 2 for new OSS features and for a summary of migration or installation issues. Use COPYOSS or PINSTALL or both to install products that are not managed by DSM/SCM. • • If any OSS files are managed by DSM/SCM, use PINSTALL on the remaining pax archives.
Overview of Installing the H06.05 RVU Minimum Memory Requirements OSS EasySetup (T0585) The OSS EasySetup product (T0585) is available for automated setup, as described in the Open System Services Installation Guide. OSS EasySetup is a series of TACL scripts that assist a site when configuring and installing a minimal OSS subsystem for the first time or when starting, stopping, or removing an OSS subsystem.
Overview of Installing the H06.05 RVU Remote Database Facility (RDF) T0294AAP is required on all S-series nodes if these nodes are not already running the minimum required T0294AAP SPR or a subsequent SPR. Failure to install the minimum T0294AAP SPR on the S-series nodes prevents those nodes from successfully discovering Integrity NonStop NS-series server nodes and vice-versa, thereby preventing the establishment of Expand-over-ServerNet lines between S-series and H-series server nodes.
Overview of Installing the H06.05 RVU Visual Inspect Pathsend users using TS/MP 2.0. It does not apply to SCOBOL users or TS/MP 3.0 users. Migration In general, all TS/MP 2.0 applications that use Pathsend requestors and TS/MP 2.0 scripts (also called OBEY files) can run in a TS/MP 2.1 environment. However, you might need to modify the PATHMON process configuration to achieve optimum TS/MP 2.1 performance. New ACS processes must be started via SCF at system startup and must be managed.
SMF Overview of Installing the H06.05 RVU SMF Beginning in the H06.05 RVU, SMFINTRFCE (T0063) is merged into the SMF (T8472) product. The merging of these T-numbers can cause a problem if you are installing the SMF bundle (T8472H01^ACW or later) on a pre-H06.05 system without installing the entire SUT. (The problem does not occur if you are installing the entire G06.28 or later SUT.) The problem occurs because the merged version of SMF and the existing T0063 component in your current (pre-H06.
Overview of Installing the H06.05 RVU TNS/R Compilers and Tools on H-Series Systems TNS/R Compilers and Tools on H-Series Systems Use One Platform for G-Series and H-Series Development Beginning with H06.05, the G-series TNS/R compilers and development tools are supported in H-series RVUs.
NetBatch Overview of Installing the H06.
Backing Out the DSM/SCM Revision Overview of Installing the H06.05 RVU Backing Out the DSM/SCM Revision If you encounter a problem with a SUT refresh that cannot be resolved, you can back out the DSM/SCM revision. Table 1-7 maps the major tasks involved with falling back. Table 1-7. Tasks and Tools for Backing Out to the Previous SYSnn To Perform This Task... Use This Tool... Documented in This Section... 1. Submit a backout request.
IPs That Become SUT Products on H-Series Overview of Installing the H06.
2 Upgrade Checklist Use the checklist in Table 2-1 as you perform the tasks required to upgrade to the H06.05 RVU and the checklist in Table 2-2 on page 2-3 to record the information needed when performing these tasks. Note. Minimum duration for tasks is not documented for H06.05. You might have to update the service processor (SP) firmware on NonStop S-series systems for IOMF2 PMF customer-replaceable units (CRUs). H06.05 Upgrade Checklist Table 2-1. H06.05 Upgrade Checklist (page 1 of 2) 1.
H06.05 Upgrade Checklist Upgrade Checklist Table 2-1. H06.05 Upgrade Checklist (page 2 of 2) Task Description Reference 11. Load the system with the new H06.05 RVU. Loading the System on page 6-3 12. Update IOAM firmware (P-switch firmware). Managing Maintenance Entity Firmware for Processor Switch and I/O Adapter Module (IOAM) on page 1-9 and the CSSI web page 13. Update NonStop Blade Complex (NSBC) firmware. Managing Firmware in a NonStop Blade Complex on page 1-12 14.
H06.05 Required Information Checklist Upgrade Checklist H06.05 Required Information Checklist Table 2-2. H06.05 Required Information Checklist Type of Information Value Volume where SYSnn subvolumes are located (usually $SYSTEM) Current SYSnn (before upgrading to H06.05) SYSnn created during H06.
Upgrade Checklist H06.05 Required Information Checklist H06.
3 Preparing to Upgrade the Server Software (Preinstallation Tasks) This section describes tasks that are needed before updating the system console and receiving the SUT.
Preparing to Upgrade the Server Software (Preinstallation Tasks) Back Up Spooler Control files Back Up Spooler Control files Before executing the SPOOLCOM;SPOOLER,DRAIN command: • • Use the SPOOLCOM;COLLECT $collector-process, LISTOPENS command to identify processes that currently have jobs open. Use the SPOOLCOM;JOB (STATE PRINT) command to determine which jobs are currently printing. Take the appropriate action to ensure that these jobs either terminate when finished or are stopped. Caution.
Preparing to Upgrade the Server Software (Preinstallation Tasks) Save the Current Configuration File (CONFxxyy) Save the Current Configuration File (CONFxxyy) A saved system configuration file contains a copy of the current configuration database CONFIG file, saved for future use. For fallback purposes, save a copy of the current CONFIG file by using a unique file name. Do not omit this step. You can use the saved configuration file to return to an earlier, stable configuration.
Preparing to Upgrade the Server Software (Preinstallation Tasks) Check Processor Status Check Processor Status 1. Log on to the OSM Low-Level Link. The OSM Low-Level Link Application appears. 2. Select Processor Status. The Processor Status dialog box appears. The Processor Status for all processors should be Executing NonStop OS. H06.
Preparing to Upgrade the Server Software (Preinstallation Tasks) Check System Components Check System Components 1. Log on to the OSM Service Connection. See the OSM Migration Guide if you have any problems accessing OSM. After the browser session begins, you can close the original IE window. VST021.vsd 2. The System Status window indicates the overall health of a system by the color of the system icon. From the Summary menu, select System Status. Yellow indicates a possible system problem.
Preparing to Upgrade the Server Software (Preinstallation Tasks) Verify the State of the Internal ServerNet Fabric 5. For each Logical Processor in the NonStop Blade Complex (Processor Complex): a. Select the Logical Processor. b. In the Attributes tab, verify that the NSK State attribute has a value of Up and that the Halt Flag attribute has a value of False. Note. If the Halt Code or Halt Flag attributes do not match these values, see the Processor Halt Codes Manual. VST021.
Preparing to Upgrade the Server Software (Preinstallation Tasks) Verify Firmware 8. Diagnose and resolve any problems that are causing the alarm. If necessary, contact your service provider before continuing with the migration. Verify Firmware Use the OSM Service Connection to verify that all updateable firmware is at the proper revision level for your current RVU.
Preparing to Upgrade the Server Software (Preinstallation Tasks) Verify Disk Drives Verify Disk Drives 1. Enter the SCF STATUS DISK command: > SCF STATUS DISK $* 2. Verify that the STATUS DISK display includes all the disk drives and that the primary, backup, mirror, and mirror-backup paths are all described as STARTED: $SYSTEM TOOLS 48> SCF STATUS DISK $* SCF - T9082H01 - (01MAY05) (15MAR05) - 07/06/2005 10:55:16 System \ATLAS (C) 1986 Tandem (C) 2003 Hewlett Packard Development Company, L.P.
Preparing to Upgrade the Server Software (Preinstallation Tasks) Check the Status of the Spooler Collector 3. Use the SCF STATUS TAPE, DETAIL command to display the current state of the tape drive. 4. If the status of the tape drive is stopped or not ready, start the tape drive and put the tape drive online. Check the Status of the Spooler Collector Check that the spooler collector is active and not 100 percent full. At a TACL prompt, start SPOOLCOM and issue a COLLECT, STATUS command.
Preparing to Upgrade the Server Software (Preinstallation Tasks) Install Node Interoperability SPRs Status of $SYSTEM.ZSYSSWAP.SWAP00 CPU 0 CPU Pages: Total 102305* Reserved 14936 Available 87369 Peak CPU Pages ever reserved 101855 Threshold 86959 CPU pages * Default swapfile extents may not be fully allocated. Status of $SYSTEM.ZSYSSWAP.
Preparing to Upgrade the Server Software (Preinstallation Tasks) Table 3-1. Interoperability SPRs for NonStop NS-Series and NonStop S-Series Systems (continued) (page 2 of 2) Minimum SPR Product Name T0448 AAA OCA Required to prepare TNS code files to run accelerated on an Integrity NonStop NS-series platform G06.
Preparing to Upgrade the Server Software (Preinstallation Tasks) H06.
4 Installing a SUT for the H06.05 RVU Installing a new RVU or a SUT involves these DSM/SCM tasks: 1. Receive New Software Into the Archive on page 4-2 2. Create a New Software Revision on page 4-6 3. Build and Apply the New Software Revision on page 4-11 Alerts for Installing a SUT Do not use this procedure to upgrade more than one Integrity NonStop NS-series servers at a time or to install SPRs. For SPRs, see Appendix A, Using DSM/SCM to Install SPRs.
Installing a SUT for the H06.05 RVU • • • Back Up Important Files Pause the hometerm configured for use by DSM/SCM Pathway servers and other processes when DSM/SCM is running. The default hometerm is $ZHOME. See the DSM/SCM User’s Guide for more information about the hometerm used by DSM/SCM Pathway servers. For those OSS products that are not managed by DSM/SCM, you must install them manually using PINSTALL or COPYOSS. A new processor type is introduced in H-series RVUs, NSE-A. On the initial H06.
Installing a SUT for the H06.05 RVU Receive New Software Into the Archive The Planner Interface screen displays two dialog boxes: • • The Software in Archive dialog box lists the software that is currently in the DSM/SCM Archive. The Configuration Revisions dialog box lists the current software revisions. 4. In the Software in Archive dialog box, click Receive software. The Receive Software Request dialog box appears. For example: VST505.vsd 5.
Installing a SUT for the H06.05 RVU Receive New Software Into the Archive The Request Scheduling Options dialog box appears. Make the appropriate selections and click OK. VST553.vsd The Request Scheduling Options dialog box closes. 11. In the Receive Software Request dialog box, click OK. A Status window appears and is updated automatically at regular intervals. 12. While waiting for the request to finish, check: • The status of the request in the Status window. For example: H06.
Installing a SUT for the H06.05 RVU • Receive New Software Into the Archive EMS event messages to see if a cartridge on a nonautoloading drive of the SUT needs to be mounted. EMS messages are displayed in these windows: ° ° The OutsideView EMS Event Stream window The EMS Events window displayed by DSM/SCM when you click Show EMS events from the Status window You can also check the Requests window to ensure that the request is finished. (Select Requests>Requests list.) For example: VST525.vsd 13.
Create a New Software Revision Installing a SUT for the H06.05 RVU Create a New Software Revision When you create a new software revision, DSM/SCM selects the products in the SUT that are licensed for your site and replaces any previous versions of the products. The following steps assume that you are creating a new software revision that manages OSS files. If you are not, go to step 6 after you are in the Planner Interface Configuration Revisions window.
Create a New Software Revision Installing a SUT for the H06.05 RVU VST023.vsd b. Click Output to view the default output values. c. Enter the appropriate values in the data fields. Note. On H-series systems, the alternate name for the $SYSTEM drive now defaults to $FC1 for fibre channel drives or $SCSI for SCSI drives. If this default has been changed, then the target volume specified in the Planner Interface for new subvolumes must reflect this change. $SYSTEM $FC1 d. Click OK.
Installing a SUT for the H06.05 RVU Create a New Software Revision 5. Click OK to return to the Planner Interface. 6. Select New software revision. DSM/SCM opens a New software revisions dialog box that lists the products in the last software revision that was built for the target system. It might take several minutes for the dialog box to appear. a. In the New software revision dialog box, click Edit revision notes. A Revision Notes text box containing existing revision notes appears. b.
Installing a SUT for the H06.05 RVU Create a New Software Revision vst657.vst The dialog box lists non-SUT products installed on the previous SYSnn that are not available on the new configuration. For products that are available on the H06.05 SUT, see IPs That Become SUT Products on H-Series on page 1-32.
Installing a SUT for the H06.05 RVU Create a New Software Revision 8. Keep the Planner Interface open for the next task. H06.
Installing a SUT for the H06.05 RVU Build and Apply the New Software Revision Build and Apply the New Software Revision The Build process creates an activation package containing all the products listed in the new software revision. Note. The Activation Package contains installation instructions for the pax files of those OSS products that contain A7CINFO files in their distributed subvolumes.
Installing a SUT for the H06.05 RVU Build and Apply the New Software Revision 2. Under Perform steps, select Build, apply & process snapshot. 3. In the Activation SYSnn: box, enter a unique number to create a new SYSnn subvolume. The value nn must be a two-digit octal number in the range%00...%77. You can issue a FILEINFO command at a TACL prompt to view the SYSnn subvolumes that are currently on your system. > fileinfo $system.*.osimage 4. Make a note of the new SYSnn.
Build and Apply the New Software Revision Installing a SUT for the H06.05 RVU 8. (Optional) Confirm that the spooler is active and not 100 percent full before executing the Build/Apply request. At a TACL prompt, start SPOOLCOM and issue a COLLECT, STATUS command. For example: 12> spoolcom $spls; collect, status COLLECT $S STATE ACTIVE FLAGS 3 , CPU 1 PRI 154 UNIT 4 DATA FILE %FULL $OPS0.SPL.DATA 4 9. In the Build/Apply Request dialog box, click OK. VST024.
Installing a SUT for the H06.05 RVU Build and Apply the New Software Revision VST003.vsd 10. Check EMS messages for more detailed information about your Build/Apply: a. In the Events window, click Refresh to see newer messages. b. When finished viewing, click Close. Note. If you encounter any problems, see the DSM/SCM User’s Guide or online help.
Installing a SUT for the H06.05 RVU • • Build and Apply the New Software Revision The last message in the EMS Events window shows that the input snapshot finished successfully. The Requests window shows that the request is finished. (Select Requests> Requests list). 11. Close the EMS Events, Status, and Request windows. 12. Exit the DSM/SCM Planner Interface. H06.
Installing a SUT for the H06.05 RVU Print Operator Instructions From the Target Interface (ZPHITI) Print Operator Instructions From the Target Interface (ZPHITI) Print the operator instructions that you edited. 1.
Installing a SUT for the H06.05 RVU Print Operator Instructions From the Target Interface (ZPHITI) 3. From the ZPHITI Main Menu, enter 3 (Perform target activities) in the Selection number field, and press F1 to display the Target Menu - Select Target screen.
Installing a SUT for the H06.05 RVU Recovery for Problems Installing an H06.05 SUT or SPRs An example instruction screen might look like this: Activation Instructions for \BITDRP BITDRP These are general instructions that were determined from configuration attributes. Refer to the release documentation for detailed information on migrating to this software configuration. 1. Stop all applications. Keep OSS running. 2. Update FIRMWARE. Run OSM to check firmware and perform firmware updates.
Installing a SUT for the H06.05 RVU Cancel Pending Build/Apply Requests The cancel request action takes a few minutes to finish. Note. If you cannot cancel the Build request through the DSM/SCM Planner Interface, use the DSM/SCM Target Interface (ZPHITI) to cancel the request. See the DSM/SCM User’s Guide and online help. 3. Using the Planner Interface, rename the old software inputs: a. In the Software in Archive dialog box, select the software input. b.
Installing a SUT for the H06.05 RVU Cancel Pending Build/Apply Requests H06.
5 Running ZPHIRNM During the Build/Apply phase, DSM/SCM places product files in their subvolumes with temporary (fabricated) file names so that new file names do not conflict with the file names of currently running programs. This section describes how to run the ZPHIRNM program on the target system to: • • Rename the files that currently have actual file names with fabricated names. These files become obsolete when the new files are renamed.
Back Up (Copy) Files in the $SYSTEM.ZTCPIP Subvolume (Best Practice) Running ZPHIRNM • If ZPHIRNM is run in PREVIEW mode, ZMODGP is run in TRIAL mode. However, any errors in the new and changed files will not be discovered in preview or trial mode because ZPHIRNM in preview mode does not actually rename the files. Therefore, ZMODGP will not be run against the same files as when the real file activation is done. Back Up (Copy) Files in the $SYSTEM.
Stop Applications Running ZPHIRNM Stop Applications Before running ZPHIRNM: 1. Stop DSM/SCM if it is still running. For example: > VOLUME $dsmscm_vol.ZDSMSCM > Run STOPSCM STOP CNFGINFO server process $ZPHC STOP DSM/SCM Pathway system $YPHI PATHCOM $YPHI;SHUTDOWN !,WAIT $Z02H: TCP TCP-H, STOPPED $Z02H: TCP TCP-T, STOPPED STOP DSM/SCM Alternate EMS Collector $ZPHI where $dsmscm_vol is the DSM/SCM volume. 2. Stop all other applications, except for TMF and the OSS file system.
Back Up the Spooler Control Files Running ZPHIRNM For more information on draining the spooler, see Support Note S99086, NSK Spooler—Migration and Draining Instructions and Section 1 and Appendix H in the Spooler Utilities Reference Manual. Back Up the Spooler Control Files While the spooler environment is closed, back up the spooler control files to render a known database from which you recover in case of a catastrophic spooler failure.
Using ZPHIRNM PREVIEW Mode Running ZPHIRNM Files Files Files Files Files Files Files Files processed in old configuration only ...................... processed that are shared by new and old configuration ... processed & unchanged between new and old configuration .. processed in obsolete TSVs ............................... renamed from real name to fabricated name ................ renamed from fabricated name to real name ................ renamed from real name to fabricated (ZPG) name ..........
Steps for Running ZPHIRNM Running ZPHIRNM Steps for Running ZPHIRNM 1. At a TACL prompt, enter this command from the DSM/SCM subvolume: > RUN ZPHIRNM $vol.SYSnn where: • • $vol specifies the default current system load volume, usually $SYSTEM. SYSnn specifies the subvolume to which you just applied software. The SYSnn subvolume must match the activation SYSnn that you specified earlier during the Build/Apply phase. 2. When asked if you want to use a log file with the session, enter Y. 3.
Verify That ZPHIRNM Ran Successfully Running ZPHIRNM b. Change directories by using the cd command. For example: /G/SYSTEM/STARTUP: cd /usr/share/man c. Run the merge_whatis command: /usr/share/man: merge_whatis d. Enter the list (ls) command: /usr/share/man: ls cat1 cat4 cat7 whatis.frag cat2 cat5 cat8 whatis_old cat3 cat6 whatis /usr/share/man: After you run merge_whatis, the directory contains a file named whatis, containing the database.
Running ZPHIRNM ° Verify That ZPHIRNM Ran Successfully If the subvolume was successfully processed, you can ignore warning messages. See the DSM/SCM User’s Guide for troubleshooting procedures and the DSM/SCM Messages Manual for a complete list of ZPHIRNM messages. H06.
6 Loading the H06.05 RVU This section describes how to perform a system load of the H06.05 RVU of the NonStop operating system into the memory of each processor in an Integrity NonStop NS-series server. Note. For detailed information on performing a system load of an Integrity NonStop NS-series server, see Section 15 in the NonStop NS-Series Operations Guide. By default, one $SYSTEM is already configured.
Alerts Loading the H06.05 RVU IOAM • • FCSA Disk Drive Enclosure Path Group Module Slot SAC Shelf Bay Primary 110 2 1 1 1 1 Backup 110 3 1 1 1 1 Mirror 110 3 1 2 1 1 Mirror Backup 110 2 1 2 1 1 A SCSI-Load attempts to load the system from a disk in group, module, slot 11.1.11 of a NonStop S-series I/O enclosure. See Table 6-1, System Load Paths in Order of Use, on page 6-1. You can configure additional alternate system disks.
Loading the H06.05 RVU • Halt the Processors If you have problems performing a system load, see the NonStop NS-Series Operations Guide, Section 15. Halt the Processors 1. 2. 3. 4. 5. 6. 7. Log on to the OSM Low-Level Link. On the toolbar, click Processor Status to display the Processor Status dialog box. Under Processor Status, select all processors. From the Processor Actions list, select Halt. Click Perform action.
Loading the H06.05 RVU Steps for Loading the System The CIIN file must be enabled because it contains commands needed to start the server. The startup TACL process performs the commands in the CIIN file and then logs off. For a description of the CIIN file, see the NonStop NS-Series Planning Guide. 4. Under Configuration, ensure that all the check boxes for all paths are selected. 5. Click Start System. The system load begins.
Loading the H06.05 RVU Completing the System Load (If Necessary) Four OutsideView windows, consisting of two startup event stream windows (two CNSL sessions) and two startup TACL windows (two CLCI sessions), are automatically launched. It might take a few seconds before the windows appear.
Loading the H06.05 RVU Verifying That the System Is Started Verifying That the System Is Started Verify that each processor is running the operating system: 1. Select Summary>Processor Status. The Processor Status dialog box should show each processor to be Executing NonStop OS. 2. Close the Processor Status dialog box. H06.
Loading the H06.05 RVU Verifying That the System Is Started 3. Verify that the NonStop operating system is working properly: a. Check the startup TACL window to verify that the startup scripts completed successfully. b. Check the startup event stream window and the startup TACL window for error messages. 4. Close the System Startup dialog box. For more information on system loads, see section 15 in the NonStop NS-Series Operations Guide. H06.
Loading the H06.05 RVU Verifying That the System Is Started H06.
7 Resuming Normal Operations This section describes tasks that might need to be performed after a system load. Start User and System Applications You can now start your application software. Follow your site’s procedures for executing the system configuration and startup (command) files to accomplish this. DSM/SCM is often started automatically by a system command file. If not, you must start it manually as described next. Before Starting DSM/SCM Initialize SQL for NonStop SQL/MP 1.
Resuming Normal Operations Start DSM/SCM Cold Start the Pathway Configuration 1. Verify your current configuration against the cold start configuration in PATHHOST (or PATHTARG) to check that the current configuration reflects all changes you have made. 2. Run the PATHCOLD macro from the ZDSMSCM subvolume to cold start the Pathway configuration. Start DSM/SCM 1.
Resuming Normal Operations Update NonStop TCP/IP Configuration Files Update NonStop TCP/IP Configuration Files Note. You must have all the NonStop TCP/IP configuration files in your $SYSTEM.ZTCPIP subvolume. Otherwise, applications dependent on proper network connections will fail. Alerts: • • • See Back Up (Copy) Files in the $SYSTEM.ZTCPIP Subvolume (Best Practice) on page 5-2. For the DSM/SCM Planner Interface to be operational, the PORTCONF file must have the correct entry for DSM/SCM.
Update NonStop TCP/IP Configuration Files Resuming Normal Operations To copy the sample files: >FUP >FUP >FUP >FUP >FUP >FUP DUP DUP DUP DUP DUP DUP $SYSTEM.ZTCPIP.SMPLHOST, $SYSTEM.ZTCPIP.SMPLPROT, $SYSTEM.ZTCPIP.SMPLNETW, $SYSTEM.ZTCPIP.SMPLPORT, $SYSTEM.ZTCPIP.SMPLRESC, $SYSTEM.ZTCPIP.SMPLSERV, $SYSTEM.ZTCPIP.HOSTS $SYSTEM.ZTCPIP.PROTOCOL $SYSTEM.ZTCPIP.NETWORKS $SYSTEM.ZTCPIP.PORTCONF $SYSTEM.ZTCPIP.RESCONF $SYSTEM.ZTCPIP.SERVICES Step 2: Check the PROTOCOL File (Optional) Caution.
Configure OSS Resuming Normal Operations 58> type portconf # # This file tells the listner program which ports to # listen to, and what programs to run # Telnet is directly, and does not use the listner's # services. # To run the listner use: # $system.ztcpip.listner / name.../ [config-file-name] # where config-file-name is this file. # ftp finger phiwsock $system.ztcpip.ftpserv $system.ztcpip.fingserv $system.ztcpip.echoserv $tdsv.zdsmscm.
Resuming Normal Operations Configure SMF (Optional) Guide for a description of PINSTALL use, or the pinstall(1) reference page in the OSS Shell and Utilities Reference Manual. See also the appropriate product’s softdoc for any pre- or post installation instructions. Run the inetd Process Run the inetd process immediately after loading the OSS product files into the OSS environment. The inetd process listens for connections on certain Internet sockets.
Resuming Normal Operations Configure the Remote Database Facility (RDF) To ensure system configuration integrity, always: 1. Save the system configuration after SMF configuration changes are made. 2. Reload the system from the current system configuration file or the latest version with SMF changes. See the softdoc T8472ACK or later for SMF configuration and interoperability considerations.
Resuming Normal Operations Configure the WAN Manager H06.
8 Backing Out the DSM/SCM Revision This section describes: • • Products that might have fallback implications. Before falling back or backing out the revision, review the appropriate product softdocs. Using DSM/SCM to back out the revision. Products That Might Have Fallback Implications Review the H06.05 Release Version Update Compendium and product softdocs to make sure that your installed products do not have migration implications.
Before Backing Out the Revision Backing Out the DSM/SCM Revision Before Backing Out the Revision 1. Confirm that the spooler is active and not 100 percent full. a. At a TACL prompt, start SPOOLCOM and issue a COLLECT, STATUS command. For example: 12> spoolcom $spls; collect, status COLLECT STATE FLAGS $S ACTIVE CPU 3 , 1 PRI UNIT 154 4 DATA FILE %FULL $OPS0.SPL.DATA 4 b. If the spooler is not active, start the spooler.
Backing Out the DSM/SCM Revision Submit a Backout Request 2. Enter your user ID or alias and password and press F1 to log on to the Target Interface.
Backing Out the DSM/SCM Revision Submit a Backout Request The Target Menu - Select Action screen appears: DSM Software Configuration Manager Target Menu - Select Action ============================================================================== \ELI Prior snapshot 2003-04-14:18:03:03 DEFAULT Last S/W applied on SYS 00 on 2000-04-14:18:01 Selection number: ============================================================================== Choose an action by entering the selection number of an item from the
Backing Out the DSM/SCM Revision Submit a Backout Request 4. Press F1 to submit the backout request. DSM/SCM automatically reapplies the previous software revision. While the backout request is processing, DSM/SCM displays the Backout - Processing Backout screen, which gives a description of the request, its processing status, and the location of the previous SYSnn software affected by the request.
Backing Out the DSM/SCM Revision Monitor the Backout Process A complete set of operator instructions might look like this: DSM Software Configuration Manager Backout - Complete Backout ============================================================================== \ELI Prior snapshot 2002-04-14:18:03:03 DEFAULT Last S/W applied on SYS on 2000-04-14:18:01 Print operator instructions on: ============================================================================== Placement of files for this Backout is comp
Backing Out the DSM/SCM Revision Monitor the Backout Process vst100.vsd H06.
Backing Out the DSM/SCM Revision Monitor the Backout Process H06.
9 Running ZPHIRNM to Reactivate the Previous Software Revision This section describes how to run the ZPHIRNM program again to change the temporary names of the previous product files back to their actual names. Alerts Before running ZPHIRNM: • • • • Applications that use files that are being replaced should not be running. To avoid any possibility of conflict, stop all applications, except for the TMF subsystem, before running ZPHIRNM. You must have rename (purge) access to all files being renamed.
Running ZPHIRNM to Reactivate the Previous Software Revision Run ZPHIRNM This command causes the spooler to move from the active to the dormant state. Caution. Do not use the TACL STOP command to drain or stop the spooler. Also, do not issue the TACL STOP command after you have issued the SPOOLCOM DRAIN command. The control file can be corrupted during the next warmstart or rebuild. For more information on draining the spooler and recovery, see Section 1 in the Spooler Utilities Reference Manual.
Running ZPHIRNM to Reactivate the Previous Software Revision Verify That ZPHIRNM Ran Successfully Verify That ZPHIRNM Ran Successfully 1. Review the log file. 2. If ZPHIRNM did not run successfully, correct the problem and rerun. Two types of error and warning messages are issued during the renaming process: • • If a fatal error occurs, ZPHIRNM immediately issues an error message and stops. A nonfatal error is one that affects processing only for a single subvolume.
Running ZPHIRNM to Reactivate the Previous Software Revision Verify That ZPHIRNM Ran Successfully H06.
10 Loading the Previous RVU and Resuming Normal Operations This section describes how to perform a system load of the previous RVU of the NonStop operating system into the memory of each processor in an Integrity NonStop NS-series server. Alerts Before performing a system load: • Before halting the processors, stop running applications, including TMF. Note. To stop TMF, at a TACL prompt, enter: 5> TMFCOM STOP TMF • • • • Do not close the System Startup dialog box while startup is in progress.
Loading the Previous RVU and Resuming Normal Operations Halt the Processors Halt the Processors Halting the processors or stopping the system is the same in H-series RVUs as in G-series RVUs. 1. Log on to the OSM Low-Level Link. 2. On the toolbar, click Processor Status to display the Processor Status dialog box. 3. In the Processor Status box, select all processors. 4. From the Processor Actions list, select Halt. 5. Click Perform action. 6. Click OK when asked “Are you sure you want to do Halts?” 7.
Loading the Previous RVU and Resuming Normal Operations Loading the System 4. Under Configuration, ensure that the correct paths are checked. 5. In the System Load dialog box, click Start System. The system load begins. If you want to stop the load process, click Abort in the System Load dialog box. You might wait up to 30 seconds before the abort takes effect. Caution. Do not close the System Load dialog box while startup is in progress.
Loading the Previous RVU and Resuming Normal Operations Completing the System Load (If Necessary) Completing the System Load (If Necessary) Loading the processors with the CIIN file is usually automatic. However, if the operating system loaded successfully into processor 0 or processor 1, but the commands in the CIIN file do not reload all remaining processors, use the RELOAD TACL commands. You must be super ID (255,255) to load the processors. 1.
Loading the Previous RVU and Resuming Normal Operations Reverting to H06.04 NonStop Blade Complex Firmware 3. When the Actions window appears, select Firmware Update from the Available Actions list. 4. Click Perform action. 5. In the guided procedures interface, click Start in the Procedure Tasks List pane. 6. Follow and complete the guided procedure dialog boxes using this summary: a. Update NonStop Blade Complex (NSBC) firmware: 1.
Loading the Previous RVU and Resuming Normal Operations Reverting to H06.04 NonStop Blade Complex Firmware 3. Load (coldload) the system with the H06.04 RVU. c. Update NonStop Blade Complex (NSBC) firmware on the other flash, as follows: 1. Using the OSM Service Connection and the Blade Complex Firmware Update guided procedure, complete the dialog boxes and update the shadow firmware on each NonStop Blade Element. Note.
A Using DSM/SCM to Install SPRs SPRs provide new features between RVUs or correct software problems from a previous RVU. This appendix describes tools available for investigating SPRs and instructions on how to install SPRs. Caution. Do not apply any SPR to an RVU without first verifying (by using Scout for NonStop Servers, for example) that the SPR can be installed on that specific H-series RVU. See the H06.
Using DSM/SCM to Install SPRs DSM/SCM DSM/SCM DSM/SCM has automatic features that can help you keep records of SPRs. You can use the DSM/SCM Planner Interface to generate a number of prepackaged reports, including reports that list: • • • The products on a system and the SPRs applied to those products The SPRs that have been replaced by a specific SPR The requisite SPRs for a selected SPR You can also use the DSM/SCM Archive to export SPRs to different SYSnns.
Determine the Current SYSnn Using DSM/SCM to Install SPRs 3. Save the current configuration by using a unique file name. At the SCF prompt, enter: -> SAVE CONFIGURATION xx.yy where xx.yy is a number from 0.0 through 99.99. This example saves the current system configuration to the file $SYSTEM.ZSYSCONF.CONF1101: -> SAVE CONFIGURATION 11.1 The configuration file $SYSTEM.ZSYSCONF.CONF1101 has been created. If you specify a configuration file that already exists, SCF asks you if you want to replace it.
Using DSM/SCM to Install SPRs Receive the SPR Into the DSM/SCM Archive 3. At a TACL prompt, enter a STATUS 0,0 command to see which SYSnn subvolume is currently being used: 3> status 0,0 System \ELI Process Pri PFR %WT Userid Program file 0,0 201 P R 000 255,255 $SYSTEM.SYS01.NMONTOR Swap File Name: $SYSTEM.#0 Hometerm $YMIOP.#CLCI Receive the SPR Into the DSM/SCM Archive Before Starting DSM/SCM 1. Verify that both OutsideView Startup TACL windows ($YMIOP.#CLCI) are open.
Using DSM/SCM to Install SPRs Create a New Software Configuration That Includes the SPR Create a New Software Configuration That Includes the SPR After the SPR has been received into the Archive, you can copy it. To create a new software configuration that includes the SPR: 1. In the Configuration Revisions dialog box, select the configuration you are updating, and click New Software Revision. The New software revision dialog box appears. 2.
Using DSM/SCM to Install SPRs Print Operator Instructions From the Target Interface (ZPHITI) Print Operator Instructions From the Target Interface (ZPHITI) 1. Make sure that spooler is active. 2. On the DSM/SCM subvolume, enter: RUN ZPHITI The TI Logon screen appears. 3. Enter your user ID/alias and password and press F1 to log on to the Target Interface. The Main Menu appears. 4. Enter 3 (Perform target activities) in the Selection number field and press F1.
Using DSM/SCM to Install SPRs If Running INSTALL^TEMPLATES Is Required For example: > RUN ZPHIRNM $system.SYS00 2. When asked if you want to use a log file with the session, enter Y and press Enter. 3. When prompted, enter a file name for the log file. ZPHIRNM issues this message and begins processing: Log file is open, Zphirnm will now begin processing. 4. Verify that ZPHIRNM ran successfully by reviewing the log file. 5. If ZPHIRNM did not run successfully, correct the problem and rerun.
Using DSM/SCM to Install SPRs If Running INSTALL^TEMPLATES Is Required Note. If you run the INSTALL^TEMPLATES macro with no arguments, you are prompted to provide required information. For information on the INSTALL^TEMPLATES arguments, print the usage notes: -> volume $system.zinsaids -> load /keep 1/ TACLMACS -> install^templates /out outdev/ help where outdev is the name of the desired output device. 3. Choose a location on $SYSTEM to keep updated template files: tacl>volume $system.template 4.
Using DSM/SCM to Install SPRs If a System Load Is Required To correct the problem: 1. Rename the current files: tacl> rename newres, oldres tacl> rename newnres, oldnres 2. Run the INSTALL^TEMPLATES macro again and use the file names newres and newnres. This message indicates that the templates are successfully installed: >$SYSTEM.SYS00.FUP /NAME $Z03M,INV :INBUF.1,OUTV :OUTBUF.
Using DSM/SCM to Install SPRs Perform a System Load Perform a System Load A normal system load consists of loading the operating system from disk into the memory of processor 0 or processor 1. See Section 6, Loading the H06.05 RVU for information on performing a system load. Start Your Applications and Processes After you have reloaded the processors and the Processor Status screen shows all processors executing the NonStop operating system, you can start your applications and processes.
B Installing SWID, DSM/SCM PVU, and Planner Interface (PI) Client Software Note. • • For Integrity NonStop NS-series servers, you must have installed both the DSM/SCM SPR and the corresponding client version before you receive an RVU SUT. For H06.05, all newly shipped Integrity NonStop NS-series servers will have the latest DSM/SCM SPR installed. The latest DSM/SCM client version is available only on the SUT unless you have ordered new system consoles.
Installing SWID, DSM/SCM PVU, and Planner Interface (PI) Client Software Determine the Latest SWID Product If your VPROC commands do not display the following versions, install the latest H02 DSM/SCM product version as described in Copy (RESTORE) the H02 DSM/SCM Product Version to Disk (If Necessary) on page B-4: This example shows the H02 product version of DSM/SCM after DSM/SCM has been activated for H06.05. (Bold lettering is used to show the VPROC command and the latest version): \DRP08.$DSMSCM.
Installing SWID, DSM/SCM PVU, and Planner Interface (PI) Client Software Determine the Product Version of DSM/SCM on the Client Determine the Product Version of DSM/SCM on the Client To determine which product version of DSM/SCM client software is installed, start the DSM/SCM Planner Interface. Before prompting you to log on, the About DSM/SCM window briefly displays version information. For example, the latest DSM/SCM client version for the H06.03 RVU is: VST004.
Installing SWID, DSM/SCM PVU, and Planner Interface (PI) Client Software Copy (RESTORE) the H02 DSM/SCM Product Version to Disk (If Necessary) Copy (RESTORE) the H02 DSM/SCM Product Version to Disk (If Necessary) To copy the H02 product version of DSM/SCM and the SWID product from the H06.05 RVU to disk, at a TACL prompt, enter the RESTORE command: >RESTORE/OUT $S.#nnn.DSM/$tape, ($*.E6031H02.*, *.E9298H02.
Installing SWID, DSM/SCM PVU, and Planner Interface (PI) Client Software Receive the H02 SWID and DSM/SCM SPRs VST350.vsd 8. Click OK. You are returned to the Receive Software Request dialog box. 9. Click OK to run the request immediately. (The request takes less than 5 minutes to finish.) H06.
Installing SWID, DSM/SCM PVU, and Planner Interface (PI) Client Software Receive the H02 SWID and DSM/SCM SPRs The Status dialog box appears. Wait until the display for the Request activity summary appears as Complete, and then close the Status window. For example: SOFTWARE 2002-12-07-19:09:39 Input software Complete VST351.vsd 10. Select Window>Refresh to update the Software in Archive dialog box to include the received software. H06.
Installing SWID, DSM/SCM PVU, and Planner Interface (PI) Client Software Create a New Software Revision for H02 DSM/SCM and SWID SPRs Create a New Software Revision for H02 DSM/SCM and SWID SPRs 1. In the Configuration Revisions dialog box, select the target system being upgraded and the current revision of the system being upgraded. Select New software revision. DSM/SCM opens the New dialog box listing the products in the last software revision that was built for the target.
Installing SWID, DSM/SCM PVU, and Planner Interface (PI) Client Software Build and Apply the DSM/SCM H02 Software Product Revision 2. Click Edit instructions to display the Planner Instructions box. 3. Edit the instructions to provide the current SYSnn number, and then click OK. 4. Complete the Build/Apply Request dialog box: a. Under Perform steps, select Build, apply & process snapshot. b. Enter the current SYSnn in the Activation SYSnn text box (because no SYSGEN is required). c. Click OK. VST254.
Installing SWID, DSM/SCM PVU, and Planner Interface (PI) Client Software Rename the Applied DSM/SCM H02 Files By Running ZPHIRNM Rename the Applied DSM/SCM H02 Files By Running ZPHIRNM 1. Stop DSM/SCM: > VOLUME $dsmscm_vol.ZDSMSCM > RUN STOPSCM where $dsmscm_vol is the DSM/SCM volume. 2. Run ZPHIRNM: > RUN ZPHIRNM $volume.SYSnn where SYSnn is the current SYSnn (because no SYSGEN or system load is required). 3. When asked if you want to use a log file with the session, enter Y. 4.
Installing SWID, DSM/SCM PVU, and Planner Interface (PI) Client Software Restart Applications Restart Applications You can now start your application software. Follow your site’s procedures for executing the system configuration and startup (command) files to accomplish this. DSM/SCM is often started automatically by a system command file. If not, you must start DSM/SCM manually as described next. Before Starting DSM/SCM 1. Check that TMF is started: > TMFCOM STATUS TMF 2.
Installing SWID, DSM/SCM PVU, and Planner Interface (PI) Client Software Verify That the H02 PVU of DSM/SCM Is Installed 2. If necessary, press Enter to have STARTSCM run the IPM6031 TACL macro automatically. This step takes several minutes. STARTSCM: A new version of DSM/SCM has been installed and IPM6031 needs to be run. You can either exit and run IPM6031 manually or continue and IPM6031 will be run for you. Enter to continue or BREAK to exit.
Installing SWID, DSM/SCM PVU, and Planner Interface (PI) Client Software Verify That SWID Is Installed Verify That SWID Is Installed This example shows the H02 product version of SWID. Use the VPROC command: \DRP08.$SYSTEM.SYSTEM 101> vproc swid VPROC - T9617H01 - (01 OCT 2004) SYSTEM \DRP08 Date 13 FEB 2006, 14:41:43 Copyright 2004 Hewlett-Packard Development Company, L.P. $SYSTEM.SYSTEM.
Installing SWID, DSM/SCM PVU, and Planner Interface (PI) Client Software Install the DSM/SCM Client From ZDSMSCM Install the DSM/SCM Client From ZDSMSCM Note. Before you begin, back up your current DSM/SCM folder to save the configuration information and the Planner Interface version. Check that unnecessary PC programs are not running before you begin the DSM/SCM client installation and that no DSM/SCM Build or Applies are in progress.
Installing SWID, DSM/SCM PVU, and Planner Interface (PI) Client Software Copy the ZDSMSCM Client File From the Host Notepad opens the DSM/SCM initialization file. For example: IP Address IP Port Number VST005.vsd 5. Make a note of the IP address and port number. 6. Close the dsmscm.ini file. Copy the ZDSMSCM Client File From the Host Note. If you are not using OutSideView on the PC that manages DSM/SCM: 1. On the NonStop operating system host system, make $dsmscm_vol.ZDSMSCM the current subvolume.
Installing SWID, DSM/SCM PVU, and Planner Interface (PI) Client Software Install the DSM/SCM Client Software 7. Verify that Overwrite local files is selected. 8. Click OK. The download should take approximately 2 minutes. 9. When the IXF - Receive dialog box indicates that the transfer is finished, click End Transfer. 10. Using Windows Explorer, rename the file from zdsmexe to zdsm.exe. 11. Double-click the zdsm.exe file to decompress the DSM/SCM client files. 12. Press any key to continue the setup. 13.
Installing SWID, DSM/SCM PVU, and Planner Interface (PI) Client Software Install the DSM/SCM Client Software VST021.vsd 3. Click Next to accept the default (private) or type in shared and click Next. Note. Private software product groups can be used only by the planner who creates the grouping. Shared software product groups can be used by other planners. For more information on these options, see the DSM/SCM User’s Guide. The Enter CNFGINFO Process Name dialog box appears with the default name $ZPHC.
Installing SWID, DSM/SCM PVU, and Planner Interface (PI) Client Software Install the DSM/SCM Client Software VST020.vsd 5. Check that WINSOCK is selected. Click Next. The Choose Destination Location dialog box appears with the default path displayed, based on your operating system (either Windows 2000 or Windows XP Professional): VST025.vsd 6. Click Next to accept the default. You are now prompted to enter an IP address: H06.
Installing SWID, DSM/SCM PVU, and Planner Interface (PI) Client Software Install the DSM/SCM Client Software VST030.vsd 7. Enter the IP address for the host system with which DSM/SCM communicates (see Determine the Current IP Address and Port Number on page B-13), and click Next. Note. If DSM/SCM is not currently configured to communicate with a host system, accept the default IP address. You can always change this value later by editing the dsmscm.ini file.
Installing SWID, DSM/SCM PVU, and Planner Interface (PI) Client Software Install the DSM/SCM Client Software 8. Enter the IP port number for the Winsock service (see Determine the Current IP Address and Port Number on page B-13), and click Next. Note. If DSM/SCM is not currently configured to communicate with a host system, accept the default IP port number. You can always change this value later by editing the dsmscm.ini file. You are now prompted to enter the host system name. VST040.vsd 9.
Installing SWID, DSM/SCM PVU, and Planner Interface (PI) Client Software Create an Emergency Repair Disk (ERD) or Automated System Recovery (ASR) Disk The setup program adds the DSM/SCM client software to the Windows Start>Programs menu. You can start the DSM/SCM Planner Interface or CNFGINFO tool from the Start>Programs>DSM_SCM submenu. For example: VST130.
Installing SWID, DSM/SCM PVU, and Planner Interface (PI) Client Software Create an Emergency Repair Disk (ERD) or Automated System Recovery (ASR) Disk c. If you want to create a backup copy of your data, click Backup Wizard and follow the instructions on the screen. 4. You have created an ERD or ASR disk. Remove the disk from the drive and store it in a secure location. H06.
Installing SWID, DSM/SCM PVU, and Planner Interface (PI) Client Software Create an Emergency Repair Disk (ERD) or Automated System Recovery (ASR) Disk H06.
C Updating SWAN Concentrator CLIP Firmware If necessary, you can update the SWAN or SWAN 2 concentrator CLIP firmware after you have completed a system load of the new RVU. Use the OSM Service Connection or SCF for some or all the tasks. For troubleshooting information on SWAN or SWAN 2, see the SWAN Concentrator and WAN Subsystem Troubleshooting Guide. Yellow caution symbols might appear on enclosure icons and on SWANs during the firmware update.
Updating SWAN Concentrator CLIP Firmware Step 1: Stop the SWAN Concentrator and CLIPs Step 1: Stop the SWAN Concentrator and CLIPs 1. Select Display>Multi-Resource Actions. The Multi-Resource Actions dialog box appears. 2. From the Resource Type list, select CLIP. 3. From the Action list, select Stop. 4. Select the SWAN CLIPS you want to stop and click Add or Add all. The selected CLIPs are added. Note that they are still in the Started state. VST960.vsd 5. Click Perform action.
Updating SWAN Concentrator CLIP Firmware Step 2: Check the Location and Version of the SWAN Firmware VST951.vsd 6. Click OK. The Progress list shows the status of the CLIP action. 7. Wait until all CLIPs are stopped before proceeding. Step 2: Check the Location and Version of the SWAN Firmware In the OSM Service Connection, look under the Firmware heading in the Attribute pane for SWAN CLIPS. The location and the version of the SWAN firmware is displayed.
Updating SWAN Concentrator CLIP Firmware Step 3: Initiate the Firmware Update 4. Leave blank the $SYSTEM.CSSnn subvolume and filename (CP7953P00) created during the most recent DSM/SCM Build/Apply, and click OK. If you have just loaded the new RVU, the SWAN firmware location should point to the correct subvolume and file version. However, if you have performed a Build/Apply for a new SWAN firmware SPR, specify that location and click OK. 5.
Updating SWAN Concentrator CLIP Firmware Step 4: Start the SWAN Concentrator and CLIPs Step 4: Start the SWAN Concentrator and CLIPs 1. With the Multi-Resource Actions dialog box still open, from the Action list, select Start. 2. Click Add or Add all. 3. Click Perform Action. The SWAN CLIPs should start. If they do not, see the SWAN Concentrator and WAN Subsystem Troubleshooting Guide, Section 4. You can also use SCF to start the CLIP or use the Actions - CLIP dialog box.
Updating SWAN Concentrator CLIP Firmware Using SCF Commands to Aid in Updating SWAN CLIP Firmware c. Use the SCF STATUS SERVER command again to verify that the SWAN adapter object is stopped. 5. From the Available Actions list, select Firmware Update to update the firmware for that particular CLIP. 6. Click Perform action. 7. Monitor the progress in the Action Status menu. To view details of the action, click Details. 8.
To Stop the CLIPs Updating SWAN Concentrator CLIP Firmware $SYSTEM ZWANTOOL 12> run wanlnck line $x25131,diag $system.css04.d8155p00 . . VPROC from CLIP: T7954G01^21OCT99^AAF^R002 . . To Stop the CLIPs Use the SCF STOP ADAPTER command: 5> SCF STOP ADAPTER $ZZWAN.#S01, SUB ALL To Verify That CLIPs Are Stopped Use the SCF STATUS SERVER command: 2-> status server $zzwan.#s01.* WAN Manager STATUS State :......... . . WAN Manager STATUS State :......... . . WAN Manager STATUS State :......... . .
Updating SWAN Concentrator CLIP Firmware To Start the SWAN Concentrator and CLIPs To Start the SWAN Concentrator and CLIPs After the SWAN CLIP firmware has been updated, use the SCF START command to start the updated SWAN concentrator and CLIPs. SCF START ADAPTER $ZZWAN.
Glossary A7CINFO file. A configuration file distributed with OSS products that contains information on the contents of all pax (archive) files of an OSS DSV. ALLPROCESSORS paragraph. A required paragraph in the CONFTEXT configuration file that contains attributes defining the HP NonStop™ operating system image for all system processors. The ALLPROCESSORS paragraph follows the optional DEFINES paragraph. Archive.
configuration planner Glossary configuration planner. The person who manages system configuration changes and software configuration changes. This person modifies the system configuration database for system configuration changes and creates a new operating system image for software configuration changes. See also planner. configuration revision.
Glossary Gigabit Ethernet 4-port ServerNet adapter (G4SA) Gigabit Ethernet 4-port ServerNet adapter (G4SA). A multiport ServerNet adapter that provides 1000 megabits/second (Mbps) data transfer rates between HP NonStop™ systems and Ethernet LANs. guided procedure. A software tool that assists you in performing complex configuration or replacement tasks on an HP NonStop™ server. OSM guided procedures are launched through actions in the OSM Service Connection. halted-state services (HSS).
millicode Glossary millicode. The system’s lowest-level machine-dependent code, often coded in assembler language. TNS/E millicode and TNS/R millicode are functionally similar to the microcode on TNS systems. The system has several types of millicode, including machine interrupt handlers, operating system primitives, routines implicitly called from native-compiled code, emulators for TNS floating-point arithmetic, and emulators for privileged-only or long-running TNS machine operations.
Index A D A7CINFO 1-6 AUDITTRAILBUFFER parameter, DP2 and RDF performance 7-7 Automated System Recovery (ASR) B-20 DSM/SCM build process 4-11 prepackaged reports A-2 Target Interface 1-31 B E Back up files backing up important files before upgrading 3-1 ZTCPIP subvolume 5-2 Blade Complex Firmware guided procedure 1-15 Bootstrap code for H-series 1-13 Build process, DSM/SCM 4-11 Build/Apply request, defined 1-7 EasySetup 4-1 Emergency Repair Disk B-20 ESS FCHECK utility 1-23 migrating data 1-22 mod-14
K Index Installing the DSM/SCM client from ZDSMSCM B-13 INSTALL^TEMPLATES instructions A-7 using with DSM/SCM B-9 Interactive Upgrade Guide 2 1-2 Interoperability audit format issues 3-10 Interoperability SPRs for NonStop NSSeries and NonStop S-Series Systems 3-10 IPs, SUT products in H-series RVUs 1-32 P Kernel-managed swap files 3-9 Pcleanup utility 5-6 Planner Interface, changing profile information 4-7 PORTCONF file 7-4 Post-installation configuring OSS 7-5 configuring RDF 7-7 configuring SMF 7-6 u
T Index SPRs interoperability 3-10 Status dialog box, reopening 4-18, B-12 SUT, maximum size of 1-1 SWAN and SWAN 2 concentrator firmware 1-20 SWAN concentrator CLIP firmware C7953P00 C-3 object code file C-3 Swap file space, checking 3-9 SYSnn subvolumes listing 3-2, A-3 system configuration file A-2 T T6030 1-6 T6031G02 1-6 T6031H01 1-6 T6031H02 1-5 TACL RELOAD command 1-31 TAEXE B-1, B-11 TAPEBOOT 1-1 Target subvolumes (TSVs) 1-7 Target systems, changing profile information 4-7 TEMPLI program B-9 TRM2
Special Characters Index H06.
