Changing the System Name of a NonStop NS2000 Series System HP Part Number: 591976-001 Published: September 2009 Edition: J06.03 and subsequent J-series RVUs.
© Copyright 2009 Hewlett-Packard Development Company, L.P. Legal Notice See Appendix : Legal Notice (page 9) for legal notices.
About This Document This procedure describes how to change the system name of a NonStop NS2000 series system that has already been installed. Supported Release Version Updates (RVUs) This topic supports J06.03 and all subsequent J-series RVUs until otherwise indicated in a replacement publication. Intended Audience This procedure is intended for those responsible for configuring a NonStop NS2000 series system. New and Changed Information in This Edition This is a new procedure.
Changing the System Name of a NonStop NS2000 Series System Notes, Cautions and Warnings CAUTION: If you change the system name or system number on an existing system and are running complex applications such as NonStop SQL/MP, HP NonStop Transaction Management Facility (TMF), Distributed Systems Management/Software Configuration Manager (DSM/SCM), or HP NonStop Open System Services (OSS), you must reconfigure the applications with the new system name and take additional precautions to avoid losing access to
-> INFO, DETAIL The results of the INFO command show that the operation is pending until the system load. Shut Down the System 10. Shut down all subsystems. 11. From TACL, stop the OSM Service Connection: > SCF ABORT PROCESS $zzkrn.#osm-cimom 12. Purge this file: $SYSTEM.ZSERVICE.IAREPO 13. If any scripts, such as SCFCSTM or TACLCSTM, reference the system name, alter them to include the new system name. 14. Verify that the $SYSTEM alternate key file does not point to the system name.
34. Repeat the steps in this section for the second VIO enclosure. 35. After changing the system name on the second VIO enclosure, compare the LCDs of the two enclosures and verify that the system names match. Power Cycle All Processors You must power cycle the processors so that the changes you made to the VIO enclosures are recognized by the system. NOTE: The following steps use Integrated Light-Out 2 (iLO2) to power cycle the processors.
NOTE: It is not necessary to change the iLO DNS name for the NonStop system console. Perform a System Load 51. Refer to the Software Installation and Upgrade Guide for your RVU for system load instructions. NOTE: When asked if you want to edit the system list with the new system name, click OK. Edit Internet Explorer Favorites 52. Remove any entries for the old system name in the Internet Explorer Favorites for the OSM Service Connection.
Run SSOCLIM on all CLIMs Run the SSOCLIM command for every CLIM on the system. Typically there are two IDs, root and user, specified for each CLIM. You need to issue the command for both IDs on each CLIM. 62. From a TACL prompt, issue these commands for every CLIM on the system: TACL> SSOCLIM climname root password TACL> SSOCLIM climname user password Check the System Inventory 63. Take another OSM inventory of the system and compare the results to the inventory you captured previously in Preparation.
Legal Notice Legal Notice Confidential computer software. Valid license from HP required for possession, use or copying. Consistent with FAR 12.211 and 12.212, Commercial Computer Software, Computer Software Documentation, and Technical Data for Commercial Items are licensed to the U.S. Government under vendor’s standard commercial license. The information contained herein is subject to change without notice.
Standard Operating Practices Standard Operating Practices CAUTION: Replace only one FRU at a time. Attempting to replace more than one hardware component at a time might cause serious system outages, processor halts, and connectivity problems. Whenever you replace a FRU, use these standard operating practices to minimize potential damage to the equipment: • Complete HP training courses on system support for HP Integrity NonStop™ NS2000 Series systems.
Figure 1 Working in an ESD-Protected Environment NOTE: To purchase an ESD protection kit from HP, use this order number and part number: Order Number: ESD-kit Part Number: T99247-A00 ESD Guidelines 11
Safety and Compliance This section contains three types of required safety and compliance statements: • Regulatory compliance • Waste Electrical and Electronic Equipment (WEEE) • Safety Regulatory Compliance Statements The following regulatory compliance statements apply to the products documented by this manual. FCC Compliance This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules.
Taiwan (BSMI) Compliance Japan (VCCI) Compliance This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take corrective actions. European Union Notice Products with the CE Marking comply with both the EMC Directive (2004/108/EC) and the Low Voltage Directive (2006/95/EC) issued by the Commission of the European Community.
Laser Compliance This product may be provided with an optical storage device (that is, CD or DVD drive) and/or fiber optic transceiver. Each of these devices contains a laser that is classified as a Class 1 or Class 1M Laser Product in accordance with US FDA regulations and the IEC 60825-1. The product does not emit hazardous laser radiation.
Observe the following limits when connecting the product to AC power distribution devices: For PDUs that have attached AC power cords or are directly wired to the building power, the total combined leakage current should not exceed 5 percent of the rated input current for the device. “HIGH LEAKAGE CURRENT, EARTH CONNECTION ESSENTIAL BEFORE CONNECTING SUPPLY” “HOHER ABLEITSTROM. VOR INBETRIEBNAHME UNBEDINGT ERDUNGSVERBINDUNG HERSTELLEN” “COURANT DE FUITE E’LEVE’.
