Operations Guide, Fourth Edition - HP Integrity rx1620

1. At the EFI shell prompt, type this command to map the parameters for all PCI cards installed
in the system:
info io
A list of all the devices that are installed in the hp Integrity rx1620 Server and managed by
EFI drivers is displayed. The output may look like this:
Seg Bus Dev Fnc Vendor Device Slot
# # # # ID ID # Path
--- --- --- --- ------ ------ --- -----------
00 00 01 00 0x1033 0x0035 XX Acpi(HWP0002,0)/Pci(1|0)
00 00 01 01 0x1033 0x0035 XX Acpi(HWP0002,0)/Pci(1|1)
00 00 01 02 0x1033 0x00E0 XX Acpi(HWP0002,0)/Pci(1|2)
00 00 02 00 0x1095 0x0649 XX Acpi(HWP0002,0)/Pci(2|0)
00 00 03 00 0x8086 0x1229 XX Acpi(HWP0002,0)/Pci(3|0)
00 20 01 00 0x1000 0x0030 XX Acpi(HWP0002,100)/Pci(1|0)
00 20 01 01 0x1000 0x0030 XX Acpi(HWP0002,100)/Pci(1|1)
00 20 02 00 0x14E4 0x1645 XX Acpi(HWP0002,100)/Pci(2|0)
00 40 01 00 0x1000 0x0021 02 Acpi(HWP0002,200)/Pci(1|0)
00 40 01 01 0x1000 0x0021 02 Acpi(HWP0002,200)/Pci(1|1)
00 80 01 00 0x14E4 0x1645 01 Acpi(HWP0002,400)/Pci(1|0)
00 E0 01 00 0x103C 0x1290 XX Acpi(HWP0002,700)/Pci(1|0)
00 E0 01 01 0x103C 0x1048 XX Acpi(HWP0002,700)/Pci(1|1)
00 E0 02 00 0x1002 0x5159 XX Acpi(HWP0002,700)/Pci(2|0)
In the example above, a single SCSI interface is shown in the listing. The information for
both channels of the SCSI interface is shown in bold, for highlighting purposes.
For each channel of the SCSI board, you need to note certain information. As an example,
look at the information for the SCSI interface (the first two bold lines). For each channel of
this SCSI interface, note the following information:
• Bus #—identifies the bus the device is on; for the SCSI interface, this is the same for
both channels. In this example, the bus number is 20.
• Dev #—the ID the device is assigned on the bus; for the SCSI interface, this is the same
for both channels. In this example, the SCSI interface is device 01.
• Fnc #—identifies the channel of the device (00 for channel A, 01 for channel B, and
so on). In this example, because the SCSI interface has two channels, one channel is 00
and the other is 01.
• Vendor ID—shows the device’s vendor ID; for the SCSI interface, this is the same for
both channels. For all the SCSI interface the ID is 0x1000.
• Device ID—shows the device ID; for the SCSI interface, this is the same for both
channels. For the SCSI interface the ID is 0x0030.
• Slot #—identifies the physical card slot in the system where the SCSI interface is
installed; for the SCSI interface, this is the same for both channels. In this example, the
SCSI interface is on the system board therefore the in slot number is xx.
48 Utilities