HP Insight Management WBEM Provider Events Reference Guide

Event DescriptionEvent
Severity
Event ID
Unexpected return to SAL_CHECK. Probable Cause: Unexpected return to
SAL_CHECK. Recommended Action: Reboot if necessary, if problem persists contact
your HP representative for support. WBEM EventID: 347. WBEM ProviderName:
FPL_IndicationProvider.Error5279
Unexpected return to SAL_INIT. Probable Cause: SAL_INIT has been unexpectedly
returned to. Recommended Action: Reboot if necessary, if problem persists contact
your HP representative for support. WBEM EventID: 348. WBEM ProviderName:
FPL_IndicationProvider.Error5280
Firmware is adding a DEGRADED cpu node to the device tree. Probable Cause: A
CPU that is not fully functional is installed in the cell board. Recommended Action:
Replace cpu indicated in data field of event. WBEM EventID: 349. WBEM
ProviderName: FPL_IndicationProvider.Warning5335
PD rendezvous will fail do to a Firmware Tree error. Probable Cause: Decode the
ASCII string in the data field to determine what resource is missing. Examine earlier
chassis codes to determine why that resource is unavailable. WBEM EventID: 350.
WBEM ProviderName: FPL_IndicationProvider.Error5354
The current cell is not configured as part of the expected set. Probable Cause: A bad
complex profile exists. Correct and redistribute. WBEM EventID: 351. WBEM
ProviderName: FPL_IndicationProvider.Error5359
A remote CSR could not be read. Probable Cause: Either a hardware connection
problem exists, or fabric was unable to be routed. Verify hardware and reset. WBEM
EventID: 352. WBEM ProviderName: FPL_IndicationProvider.Error5360
The current cell is too late to rendezvous with other cells. Probable Cause: This cell
took to long completing previous steps to rendezvous. A bad complex profile could
also cause this problem. WBEM EventID: 353. WBEM ProviderName:
FPL_IndicationProvider.Error5361
The current cell detected incompatible CPUs on another cell. Probable Cause: Mixed
CPU types are installed in the same partition. Remove them. WBEM EventID: 354.
WBEM ProviderName: FPL_IndicationProvider.Error5365
Current cell was too slow creating the local rendezvous set. Probable Cause: Cell too
slow. Could be bad hardware. Check for other errors and reset. Recommended Action:
If assistance is required, contact the HP Support Center. WBEM EventID: 355. WBEM
ProviderName: FPL_IndicationProvider.Error5366
Reporting cell was not included in the global cell set. Probable Cause: Fabric problem,
Connection problem or timing problem. Reset the PD. WBEM EventID: 356. WBEM
ProviderName: FPL_IndicationProvider.Error5376
No Core Cell can be selected in the PD. Probable Cause: No cells have a functioning
core IO card. Add a core IO card to a cell in the PD and reset. WBEM EventID: 357.
WBEM ProviderName: FPL_IndicationProvider.Error5380
Firmware was unable to notify utilities of the core cell number. Probable Cause:
Communication with utilities is broken. Check for earlier errors or NVRAM problems.
WBEM EventID: 358. WBEM ProviderName: FPL_IndicationProvider.Error5383
Fabric code unable to find a needed service provider. Probable Cause: The registry
is corrupt or the ROM is incomplete. WBEM EventID: 359. WBEM ProviderName:
FPL_IndicationProvider.Error5403
Error in a fabric Port. Probable Cause: Reset. WBEM EventID: 360. WBEM
ProviderName: FPL_IndicationProvider.Warning5404
Parity error detected on read from fabric. Probable Cause: Hardware problem. Check
connections and reset. WBEM EventID: 361. WBEM ProviderName:
FPL_IndicationProvider.Warning5405
Error writing to Fabric. Probable Cause: Bad hardware. WBEM EventID: 362. WBEM
ProviderName: FPL_IndicationProvider.Warning5406
Platform Events 23