HP Insight Management WBEM Provider Events Reference Guide

Event DescriptionEvent
Severity
Event ID
Firmware is preparing to reset for reconfiguration. Probable Cause: This can be caused
by many conditions including a bad complex profile, a bad hardware configuration,
a cell arriving late to the rendezvous point. A cell not being able to rendezvous.
Reconfiguration from partition manager is recommended. WBEM EventID: 412.
WBEM ProviderName: FPL_IndicationProvider.Error5505
An error was encountered communicating with utilities during PD rendez. Probable
Cause: Verify communications with the utilities system. WBEM EventID: 413. WBEM
ProviderName: FPL_IndicationProvider.Error5507
Forward Progress is stopping. The Cell or System will not boot further. Probable
Cause: An error occurred which triggered system firmware to cease making forward
progress. The CPU is put into a spin loop so that external debugging can take place.
See earlier event ids to help determine the cause of the error. Also note that the Error
Response Mode is likely to have directed firmware to HALT. WBEM EventID: 414.
WBEM ProviderName: FPL_IndicationProvider.Error5509
No console is available for the DUI to use. Probable Cause: DUI was entered before
the console is available. DUI will exit and processing will continue. WBEM EventID:
415. WBEM ProviderName: FPL_IndicationProvider.Warning5510
Error Processing encountered an unrecoverable error. Probable Cause: Decode the
ASCII message and correct the problem. WBEM EventID: 416. WBEM ProviderName:
FPL_IndicationProvider.Error5511
System is unable to complete the Reset For Reconfiguration request. Probable Cause:
Delay the request for reconfiguration until after the PD has been released from Sinc
BIB. WBEM EventID: 417. WBEM ProviderName: FPL_IndicationProvider.Error5514
The cell is not able to reach all requested cells through the fabric. Probable Cause:
Fabric wasn't able to route to all cells described in the complex profile correctly due
to a hardware problem. Some of the cells are unreachable. Update the complex profile
or correct the hardware problem. WBEM EventID: 418. WBEM ProviderName:
FPL_IndicationProvider.Error5515
LBA has unexpected number of I/O Slots. Probable Cause: Unsupported I/O
configuration. Recommended Action: Remove the I/O cards below the specified
PCI-to-PCI bridge. WBEM EventID: 419. WBEM ProviderName:
FPL_IndicationProvider.Warning5518
Console device failed to connect. Probable Cause: Debugging event, not for release.
WBEM EventID: 420. WBEM ProviderName: FPL_IndicationProvider.Error5521
Copying memory test code failed. Probable Cause: Memory test code located in main
memory has been corrupted. Recommended Action: Contact HP support personnel
to troubleshoot the problem. WBEM EventID: 421. WBEM ProviderName:
FPL_IndicationProvider.Warning5525
A remote cell is in an unknown state of PD rendezvous. Probable Cause: Reset the
PD. WBEM EventID: 2430. WBEM ProviderName: FPL_IndicationProvider.Error5527
Multiple Core Cells have been discovered in the same PD. Probable Cause: Verify
that the complex profile is correct and reset the partition. WBEM EventID: 423. WBEM
ProviderName: FPL_IndicationProvider.Error5528
The utilities component encountered an error when sending a command to the MP.
Probable Cause: Verify the utilities system is connected correctly and reset. WBEM
EventID: 424. WBEM ProviderName: FPL_IndicationProvider.Error5529
Error received after issuing the Retrieve Cell Slot State command. Probable Cause:
Make sure the GSP is connected and reset. WBEM EventID: 1007. WBEM
ProviderName: FPL_IndicationProvider.Warning5530
This indicates that all the cpus in the cell did not rendezvous during the MCA.
Probable Cause: When this happens the cell will step through some of the error
logging code on its own and then reset itself. WBEM EventID: 426. WBEM
ProviderName: FPL_IndicationProvider.Error5546
Platform Events 27