hp.
hp.
hp.
hp.book Page 6 Thursday, April 2, 1998 4:33 PM © Copyright 1997, 1998 Hewlett-Packard Company. All rights reserved. Reproduction, adaptation or translation without prior written permission is prohibited, except as allowed under the copyright laws.
hp.book Page 7 Thursday, April 2, 1998 4:33 PM Preface Thank you for purchasing the HP CD-ROM Server! The HP CD-ROM Server provides a simple and cost-effective way to allow information stored on CD-ROMs to be shared by all users on an Ethernet network. The HP CD-ROM Server provides multi-protocol support for most network operating systems. As additional support and new features become available, it provides the ability to upgrade firmware for future investment protection.
hp.book Page 8 Thursday, April 2, 1998 4:33 PM HP Customer Support Numbers If you need assistance, call one of the following numbers. In the USA and Canada, call 208-323-2551 In Europe, call the following number for your country: Austria 06.60.63.86 Netherlands 020.606.87.51 Belgium (Dutch) 02.626.88.06 Norway 22.11.62.99 Belgium (French) 02.626.88.07 Portugal 01.44.17.199 Denmark 39.29.40.99 Spain 90.23.21.123 Finland 02.03.47.288 Sweden 08.61.92.170 France 04.50.43.98.
hp.book Page 5 Thursday, April 2, 1998 4:33 PM Table of Contents Preface HP Customer Support Numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Electronic Support Services . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Table of Contents 1. Introduction HP CD-ROM Servers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . How They Work. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
hp.book Page 6 Thursday, April 2, 1998 4:33 PM 6. Security Management How to Setup Access Restrictions . . . . . . . . . . . . . . . . . . . . . . . . . . . . HP CD-ROM Server Access Rights . . . . . . . . . . . . . . . . . . . . . . . . . . . Security Management using a Web Browser . . . . . . . . . . . . . . . . . . . Security Management using a Text Editor . . . . . . . . . . . . . . . . . . . . . Security Management in Specific Network Environments . . . . . . . . 6-1 6-2 6-3 6-6 6-9 A.
hp.book Page 1 Thursday, April 2, 1998 4:33 PM 1 Introduction HP CD-ROM Servers HP CD-ROM Servers connect CD-ROM drives to Ethernet networks. All users on the network can share the information on any CD-ROM inserted into a connected CD-ROM drive. HP CD-ROM Server Stand-Alone Module Stand-Alone Module Tower Module HP CD-ROM Server Tower Module The stand-alone module provides RJ-45 and BNC network connectors. The RJ-45 connector connects to a 10Base-T (twisted-pair cable) network.
hp.book Page 2 Thursday, April 2, 1998 4:33 PM The 50-pin SCSI-2 header (typically for SCSI ribbon cable) supports up to 7 CD-ROM drives, or up to 56 discs if disc changers are used. The CD-ROM tower module is designed for installation into a CD-ROM tower. How They Work HP CD-ROM Servers connect as nodes on an Ethernet network. An HP CD-ROM Server acts as a network file server. This means that it is independent of other file servers—a network client communicates directly with the CD-ROM server.
hp.book Page 3 Thursday, April 2, 1998 4:33 PM Where to Use Them HP CD-ROM Servers can be used in a variety of network environments. It supports basic messaging and network protocols, including: • NCP (NetWare Control Protocol) over IPX • SMB (Server Message Block) over NetBEUI (NetBIOS Extended User Interface) • SMB over NetBIOS/TCP/IP • NFS (Network File System) over UDP/IP.
hp.book Page 4 Thursday, April 2, 1998 4:33 PM Flexibility As a network node, the HP CD-ROM Server can be located anywhere on the network, either close to users or in secured areas. Since it is a multi-protocol device, it can simultaneously support a variety of network operating environments, including Novell NetWare, Microsoft and IBM Network Operating systems, UNIX and Internet/intranets. HP CD-ROM Servers also provides flexible connectivity to CD-ROM drives and CD-ROM disc changers.
hp.book Page 1 Thursday, April 2, 1998 4:33 PM 2 Basic Installation Overview A typical Ethernet network using an HP CD-ROM Server Stand-Alone Module is illustrated below. For a Tower Module, the CD-ROM drives and tower module will normally be installed inside a tower chassis.
hp.book Page 2 Thursday, April 2, 1998 4:33 PM Unpacking Unpack and inspect all parts for damage. Contact your dealer if anything is missing. All packaging materials can be recycled. Each HP CD-ROM Server product contains the following: • CD-ROM server module • HP CD-ROM Server User’s Guide (this manual).
hp.book Page 3 Thursday, April 2, 1998 4:33 PM Accessories You may need some additional hardware to complete your installation. Available hardware from Hewlett-Packard are listed below. SCSI Cables Note For the Stand-Alone Module Only. HP provides the following SCSI-2 cables and terminators. For other SCSI-2 cables or terminators, consult with HP or your local cable vendor. ❏ Industry-standard SCSI-2 cables and terminators are available in different lengths and with different connector types.
hp.book Page 4 Thursday, April 2, 1998 4:33 PM Transceivers For the Tower Module only. HP provides the following AUI transceivers: HP Product 28641B 28683A Towers and SCSI Drives AUI Transceiver ThinLAN coaxial cable (BNC) Fiber-optic cable (ST) HP provides the following towers and SCSI drives: HP Product C2987A C2988A C2997A Description 8-bay tower for HP CD-ROM Server Tower Module. Provides SCSI backplane plug-in connectors.
hp.book Page 5 Thursday, April 2, 1998 4:33 PM Installing the Tower Module in a CD-ROM Tower If you are installing a CD-ROM Stand-Alone Module, or if your Tower Module has already been installed in a tower, you can skip this section. The HP CD-ROM Server Tower Module is intended to be installed in standard CD-ROM towers. The dimensions of the CD-ROM server are the same as for standard CD-ROM drives, which is 5.25 inch half-height.
hp.book Page 6 Thursday, April 2, 1998 4:33 PM 5. If required, use the four screws supplied to fix the CD-ROM server in place. Use the upper or lower holes depending on the type of tower and its mounting requirements. See the figure below. CAUTION ❏ The length of the screws must not exceed 0.2 inch (5 mm). If they do, the internal components of the CD-ROM server may be damaged. 6. Attach the power cable to the CD-ROM server.
hp.book Page 7 Thursday, April 2, 1998 4:33 PM . External network connector board Proceed to “Connecting CD-ROM Drives to the CD-ROM Server”. Connecting CD-ROM Drives to the CD-ROM Server Note If your CD-ROM server tower module and drives have been pre-installed in a tower, proceed directly to “Connecting the CD-ROM Server to the Network”. You can connect up to seven SCSI CD-ROM drives to a single CD-ROM server. You must use the SCSI cables that are appropriate for your drives.
hp.book Page 8 Thursday, April 2, 1998 4:33 PM 1. Connect a SCSI cable to the SCSI connector on the CD-ROM server and to the first CD-ROM drive. Connect the SCSI cable to the first CD-ROM drive. If there are more drives (up to 7), use additional SCSI cables to connect the drives. 50-pin High-density SCSI-2 connector (Stand-Alone Module) 50-pin header SCSI-2 connector (Tower Module) 2.
hp.book Page 9 Thursday, April 2, 1998 4:33 PM Note ❏ You should refer to the documentation provided with your CD-ROM drive. Some SCSI drives may contain special termination instructions. 4. If you are installing the CD-ROM server in a tower, connect the power connector and replace the tower enclosure. Connecting the CD-ROM Server to the Network The HP CD-ROM Server Stand-Alone Module is equipped with RJ-45 (twisted-pair cable) and and BNC (thin coaxial cable connectors.
hp.book Page 10 Thursday, April 2, 1998 4:33 PM . 5 6. Turn power on using the following instructions: • Stand-alone version only: First connect power to all CD-ROM drives and turn them on. Then connect the external power supply to the HP CD-ROM Server. • Tower module only: Simply switch the power on to the entire CD-ROM tower assembly containing the drives and HP CD-ROM Server. 7. Observe the CD-ROM server’s indicator lights. They will all flash during power-on and self-test.
hp.book Page 1 Thursday, April 2, 1998 4:33 PM 3 Network Configuration This section contains configuration information for the following network environments: Note • Novell NetWare . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 3-1 • Microsoft & IBM Networks . . . . . . . . . . . . . . . . . . . . page 3-3 • TCP/IP Networks . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 3-3 ❏ To use the CD-ROM server in the TCP/IP environment you must first set its IP address.
hp.book Page 2 Thursday, April 2, 1998 4:33 PM Chapter 5 describes different methods that you can use to set the NetWare configuration in the HP CD-ROM Server; the required configuration settings are described below. Parameter name Value Description TimeZone = Must be set to the correct Time Zone that the CD-ROM server is operating in. TimeSyncSource = None Default is None. Set to NDS to enable the HP CD-ROM Server to get its time from the NetWare network.
hp.book Page 3 Thursday, April 2, 1998 4:33 PM Microsoft and IBM Networks The HP CD-ROM Server does not require any configuration when using Microsoft and IBM networks that use SMB over NetBEUI (such as Windows for Workgroups, Windows 95, Windows NT or OS/2). For instructions on making a network connection to your CD-ROM server, proceed to chapter 4. Note Microsoft and IBM networks that use SMB over TCP/IP require TCP/IP configuration as described in “TCP/IP Networks” below.
hp.book Page 4 Thursday, April 2, 1998 4:33 PM Assigning an IP Address and Host Name To establish communication with the TCP/IP network, an IP address must be assigned to the CD-ROM server and, if necessary, associated with a unique host name in your system host table. The IP address must be sent to the CD-ROM server to configure it.
hp.book Page 5 Thursday, April 2, 1998 4:33 PM Choose the method best suited to your needs. If necessary, the RARP, BOOTP and DHCP methods can be enabled or disabled by editing the RARPEnable, BOOTPEnable and DHCPEnable parameters in the config.ini file as described in chapter 5 “CD-ROM Server Configuration”. See appendix B for default values. Note ❏ Only one of the RARP, BOOTP, DHCP methods for setting the IP address should be enabled at the same time.
hp.book Page 6 Thursday, April 2, 1998 4:33 PM In UNIX, Set the IP Address Using ARP Perform the following commands to download the IP address and verify the communication. The LAN hardware address is located on the label attached underneath the HP CD-ROM Server (or on the tower chassis). The LAN hardware address is entered in pairs of digits separated by a colon. See the example below: arp -s temp ping Example: arp -s 192.124.138.
hp.book Page 7 Thursday, April 2, 1998 4:33 PM In UNIX, Set the IP Address Using RARP Follow these steps to download the Internet (IP) address using the RARP method: 1. Append the following line to your LAN hardware (MAC) address table (typically /etc/ethers): Example: 00:60:b0:11:00:86 cdserv 2. Make sure the host table and alias name databases are updated as required by your systems. 3.
hp.book Page 8 Thursday, April 2, 1998 4:33 PM Note ❏ The ht and vm fields must be entered exactly as in the example. For Ethernet, ht=ether. ❏ The ha and ip fields are the LAN hardware (MAC) address and IP address respectively. Do not use the addresses in the example above. Use the LAN hardware address specified on the label on your HP CD-ROM Server, and use the IP address that was assigned by the Network Administrator.
hp.book Page 9 Thursday, April 2, 1998 4:33 PM Time Synchronization Setting the time on the CD-ROM Server The CD-ROM server clock has a volatile memory, so the correct time must be entered whenever it is restarted. By editing the CD-ROM server’s config.
hp.
hp.book Page 1 Thursday, April 2, 1998 4:33 PM 4 Mounting or Mapping Network Drives If you are new to HP CD-ROM Servers, you should read the first part of this chapter to learn about the file system and how to access the CD-ROMs. Subsequently, proceed to the appropriate section in this chapter depending on your operating environment and client system: • Novell NetWare (NCP) . . . . . . . . . . . . . . . . . . . . . . .
hp.book Page 2 Thursday, April 2, 1998 4:33 PM The HP CD-ROM Server File System The CD-ROM server will appear to your system as a file server. Like any other file server it has a directory structure where files are stored. The CD-ROM server directory structure is outlined below: These folders contain each CD-ROM’s files and data. The index file is used for Web browsing. The config folder holds configuration files used by the CD-ROM server. These folders contain the files that control access rights.
hp.book Page 3 Thursday, April 2, 1998 4:33 PM • If the system administrator has set a CD-ROM alias name, it will be used instead of the volume name. Often, a volume name is not a good representation of the CD-ROM contents. A CD-ROM alias name is a convenient way of setting a more significant or recognizable name. Note ❏ If you run an application from a CD-ROM, or look for its associated files on the CD-ROM, you may not be able to use a CD-ROM alias name because the application may not recognize it.
hp.book Page 4 Thursday, April 2, 1998 4:33 PM Three different folders are found under the volumes folder: • server folder. The files in the server folder (cd.txt, config.txt, root.txt and volumes.txt) control access to the file system of the CD-ROM server itself. The file default.txt contains the default settings to be used when either a new CD-ROM is inserted, or a new CD-ROM drive is connected. • scsi folder. The scsi folder contains a file for each SCSI ID named idlun.
hp.book Page 5 Thursday, April 2, 1998 4:33 PM Access Points The HP CD-ROM server is integrated into your network operating system just like any other file server and you use the same commands to access it. To be able to access CD-ROMs from your applications, you need to make them available to your system, that is you ‘mount’ the CD-ROM server on UNIX systems or ‘map’ the server to a drive letter on PC systems.
hp.book Page 6 Thursday, April 2, 1998 4:33 PM Novell NetWare (NCP) When accessing your CD-ROM server through NetWare, you use the same procedures as accessing any other NetWare file server. This section gives you examples of how to access the CD-ROM server from Novell clients on Windows 95, Windows NT, Windows for Workgroups and DOS.
hp.book Page 7 Thursday, April 2, 1998 4:33 PM 3. Expand the Entire Network icon and open the NetWare networking folder. 4. Double click the entry for your new CD-ROM server. The default entry name is HPhhhhhh_NW, where hhhhhh are the last six digits of the CD-ROM server LAN hardware (MAC) address. The name can be changed during configuration as described in chapter 5 “CD-ROM Server Configuration”. 5.
hp.book Page 8 Thursday, April 2, 1998 4:33 PM 6. Once you are logged in to the CD-ROM server, expand the SYS and cd folders to display all the resources: 7. If you wish to map the CD-ROM server to a drive letter, rightclick one of the following CD-ROM server resources: • For root level access, right click SYS. • For cd folder access, right click the cd folder. • For CD-ROM access, right click the CD-ROM you want to access.
hp.book Page 9 Thursday, April 2, 1998 4:33 PM 9. Select a drive letter for your CD-ROM server. 10. Check Reconnect at logon if you wish to use the CD-ROM server under the same drive letter the next time you start your computer. 11. Click the OK button. The CD-ROM server is ready for use. Windows for Workgroups 1. Start the File Manager. 2. From the Disk menu, select Connect Network Drive… The following screen is displayed.
hp.book Page 10 Thursday, April 2, 1998 4:33 PM 7. Once you are logged in to the CD-ROM server, click the Drive Connections button on the toolbar. The following screen is displayed: 8. Double click HPhhhhhh_NW\SYS and then the CD folder to display the following screen: 9. Select a drive letter in the Drives listing and then: • For root level access, select HPhhhhhh_NW_SYS in the Resources list. • For cd folder access, select the CD folder in the Resources list.
hp.book Page 11 Thursday, April 2, 1998 4:33 PM 10. Click Map to map the CD-ROM server to the selected drive letter. 11. Click Permanent if you wish to use the CD-ROM server under the same drive letter the next time you start you computer. 12. Click the Exit button on the toolbar. The CD-ROM server is ready for use. DOS The CD-ROM server is mounted using the map command. Use the map command to mount the CD-ROM server.
hp.book Page 12 Thursday, April 2, 1998 4:33 PM Microsoft and IBM Networks (SMB) You access the HP CD-ROM Server just like any other workstation or file server. Below you will find examples on how to access the CD-ROM server using clients for Windows 95, Windows NT, Windows for Workgroups, OS/2 and DOS. SMB (Server Message Blocks) is a protocol that makes use of NetBIOS. NetBIOS can be transported over several different network protocols.
hp.book Page 13 Thursday, April 2, 1998 4:33 PM Windows 95 and Windows NT 4.0 1. Start the Windows Explorer from the Start/Programs Menu. 2. Expand the Network Neighborhood icon. The available resources are displayed: 3. Expand the Entire Network icon and then open the Workgroup folder. If the Workgroup folder is not visible, refer to “Alternative Method of Connection” later in this chapter. 4. Double click the entry for your new CD-ROM server.
hp.book Page 14 Thursday, April 2, 1998 4:33 PM 5. To map a resource to a drive letter, select one of the CD-ROM server resources and use the right mouse button: • To map to all folders and files, right click root. • To map to all of the CD-ROMs, right click the cd folder. • To map to an individual CD-ROM, right click its folder. 6. From the pop-up menu, select Map Network Drive. 7. Select a drive letter for your CD-ROM server or use the default drive letter. 8.
hp.book Page 15 Thursday, April 2, 1998 4:33 PM Note ❏ In the Microsoft Network environment, network resources are accessed by specifying a server and a resource on that server using the \\server\resource syntax (UNC Universal Name Convention). The resource is not a file path and it is not possible to replace the resource name with the path to a file or folder on your CD-ROM.
hp.book Page 16 Thursday, April 2, 1998 4:33 PM Windows for Workgroups 1. Start File Manager. 2. From the Disk menu, select Connect Network Drive. The following dialog is displayed. 3. Select a drive letter or accept the default. 4. In the Path field, type an entry for your CD-ROM server, for example: \\HPhhhhhh\ where hhhhhh are the last six digits of the CD-ROM server LAN hardware address, and identifies one of the following resources: • To map at the root level, type root.
hp.book Page 17 Thursday, April 2, 1998 4:33 PM Windows NT 3.51 1. Start the File Manager. 2. From the Disk menu, select Connect Network Drive. 3. Select a drive letter or accept the default. 4. In the Path field, type an entry for your CD-ROM server, for example: \\HPhhhhhh\ where hhhhhh are the last six digits of the CD-ROM server LAN hardware address, and identifies one of the following resources: • To map at the root level, type root.
hp.book Page 18 Thursday, April 2, 1998 4:33 PM IBM Peer for OS/2 Make sure you have IBM Peer for OS/2 installed. If not, see the note below. 1. Double click the OS/2 Peer icon. The Peer window opens: 2. Double click the Sharing and Connecting icon to open the following window: Active connections will be listed in the window.
hp.book Page 19 Thursday, April 2, 1998 4:33 PM 3. From the Connection menu, select Create. The following dialog is shown: 4. In the Workstation field, enter HPhhhhhh, where hhhhhh are the last six digits of your CD-ROM server’s LAN hardware address. 5. In the Share/alias field, enter the name of the CD-ROM server folder or an individual CD-ROM: • To map at the root level, type root. • To map the CD-ROMs at the cd folder level, type cd.
hp.book Page 20 Thursday, April 2, 1998 4:33 PM If you do not have Peer for OS/2. If you do not have Peer for OS/2, the CD-ROM server can be mapped to a drive letter using the net use command. Do as follows: 1. Open an OS/2 window. 2. Use the net use command to map the CD-ROM server to a drive letter. At the OS/2 prompt, type: net use : \\HPhhhhhh\ where hhhhhh are the last six digits of your CD-ROM server’s LAN hardware address, and is any CD-ROM server folder. 3.
hp.book Page 21 Thursday, April 2, 1998 4:33 PM Example (CD-ROM access): If your CD-ROM server LAN hardware address is 0060b0cd000b, and you want to map a CD-ROM named cd_12345 to drive G, type: net use G: \\HPcd000b\cd_12345 2. To make the connections permanent, edit your autoexec.bat file to include your net use commands. Notes: ❏ If you are using DOS within Windows 95 or Windows NT 4.
hp.book Page 22 Thursday, April 2, 1998 4:33 PM 2. Mount the CD-ROM server. mount :/ Example: mount cdserv:/ /hpcd Note ❏ The is the IP address or host name assigned to the CD-ROM server during TCP/IP configuration, see “TCP/IP Networks” in chapter 3 . NFS for PC or Apple Macintosh The CD-ROM server can also be accessed through third-party NFS software for PC or Apple Macintosh computers.
hp.book Page 23 Thursday, April 2, 1998 4:33 PM 3. Enter the URL of the server, i.e. http://. Alternatively use the host name associated with the IP address and assigned to the CD-ROM server. 4. Click OK. This will bring you to the Home Page of your CD-ROM server, as shown below. From here, several links to all the functionality of the CD-ROM server, as well as external links, are available.
hp.book Page 24 Thursday, April 2, 1998 4:33 PM Adding Bookmarks in your Web browser For easy access to your CD-ROM server resources, Web pages can be saved in the “Bookmarks” or “Favorites” list in your Web browser. 1. Use the CD Access tab on the Home Page to list the CD-ROMs. If you add a bookmark at this level, you will be able to quickly return to the CD-ROM server to select one of the discs from the list of CD-ROMs installed. 2.
hp.book Page 1 Thursday, April 2, 1998 4:33 PM 5 CD-ROM Server Configuration This chapter shows how to configure the HP CD-ROM Server. The configuration can be made in the following ways: Note • Using a Web browser . . . . . . . . . . . . . . . . . . . . . . . page 5-2 This is the easiest way and is supported by on-line help instructions. However,this method requires that the CD-ROM server be configured with an Internet (IP) address on a TCP/IP network. • Using a text editor . . . . . . . . . . . . .
hp.book Page 2 Thursday, April 2, 1998 4:33 PM Configuration Using a Web Browser The configuration of the CD-ROM server can be performed from a Web browser. To access the CD-ROM server’s Home Page, an Internet (IP) address must be set on the CD-ROM server (see “TCP/IP Networks” in chapter 3). Also, the HTTPEnable parameter must be set to yes, which is the default setting. Follow the steps below to enter the configuration from a Web browser. The browser used in this example is Internet Explorer. 1.
hp.book Page 3 Thursday, April 2, 1998 4:33 PM 4. Click OK. This will open the Home Page of your HP CD-ROM Server, as shown below. Username: root Password: pass 5. Click the Advanced Configuration tab. When entering for the first time during a session you will be prompted to enter the Username (default is root) and Password (default is pass). The General Settings page will be displayed. 6. Enter the new settings. Click ‘Reset Server settings’ to return to the values before you made changes.
hp.book Page 4 Thursday, April 2, 1998 4:33 PM 7. Click Submit Server settings to download the new settings to the CD-ROM server. 8. In the menu at the left side, click the name of the next parameter group (Netware, NFS, etc.) that you wish to configure. Repeat steps 6 and 7 for each parameter group. 9. Restart the CD-ROM server to make the new settings take effect: Click the Management and Access Rights tab. In the menu at the left side, click Restart Server. Click the Restart Server button to confirm.
hp.book Page 5 Thursday, April 2, 1998 4:33 PM 3. In the config folder, locate the config.ini file. Open the file using the Windows Notepad editor or any other editor. In a standard Explorer setup, double clicking an ‘.ini’ file will automatically open the file with the Notepad editor. An example is shown below. See appendix B for a list of the config.ini file’s contents. Note ❏ The configuration file illustrated above is for version 4.11 of the HP CD-ROM Server firmware.
hp.
hp.book Page 1 Thursday, April 2, 1998 4:33 PM 6 Security Management How to Setup Access Restrictions 1. Read the general information given in “HP CD-ROM Server Access Rights” later in this chapter. 2. Choose the method you will use to set the security parameters held in the CD-ROM server’s access files: • Web Browser . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 6-3 This is the easiest way and is supported by on-line help instructions.
hp.book Page 2 Thursday, April 2, 1998 4:33 PM HP CD-ROM Server Access Rights The HP CD-ROM Server can be configured to restrict user access to CD-ROM drives, to individual CD-ROMs, and to the CD-ROM server configuration files. You can limit the number of users simultaneously accessing any CD-ROM to comply with user-license restrictions. Access restrictions are set individually for each protocol (NetWare, SMB, NFS, HTTP) through separate settings in the access files.
hp.book Page 3 Thursday, April 2, 1998 4:33 PM Comment is text that is displayed in Windows Explorer when the user is selecting CD-ROMs. • In SMB, the share level name must not exceed 12 characters. If this is insufficient for a meaningful name, you can use the comment parameter to give more information to users. The comment will also be displayed in the Web browser. • In NetWare, the comment is not available.
hp.book Page 4 Thursday, April 2, 1998 4:33 PM 2. From the File menu, select Open. The following dialog box is displayed: 3. Use the Internet (IP) address to enter the URL of the server: http:// Alternatively, you can use the host name assigned to the CD-ROM server in place of the IP address. 4. Click OK. This will open the Home Page of your CD-ROM server, as shown below.
hp.book Page 5 Thursday, April 2, 1998 4:33 PM 5. Click the Management and Access Rights tab. When entering for the first time during a session you will be prompted to enter the Username (default is root) and Password (default is pass). The page below will be displayed. If you need help, click the ? button to display the on-line help. 6. Management is grouped into four areas: General, CD-ROM Rights, Drive Rights, and Server Rights. Click the Server Rights tab for volume rights.
hp.book Page 6 Thursday, April 2, 1998 4:33 PM 7. Having selected the volume, you can now enter the new settings by editing the parameters shown on the browser page. A general explanation of the parameters is available in “The Access Control Parameters” later in this chapter. Specific information concerning each network operating system starts on page 6-9. 8. Click Submit settings to download the new setting to the CD-ROM server.
hp.book Page 7 Thursday, April 2, 1998 4:33 PM To set the access control parameters using a text editor, follow the steps below. In the examples provide, the Windows Notepad editor on a Windows 95 workstation is used. 1. Start the Windows Explorer and locate the CD-ROM server. 2. In the config folder, locate the scsi.txt file. Open the file using a text editor, such as Windows Notepad (on most systems, Notepad will run if you select and double-click a .txt file).
hp.book Page 8 Thursday, April 2, 1998 4:33 PM Note ❏ The following notes may help you when managing access rights: • The identity of a drive will appear as: idlun.txt, where is the SCSI address and the LUN address. • The name of the CD-ROM file will default to cd_nnnnn.txt (where nnnnn is an unique five digit number) if the CD-ROM does not have a name or alias name. • The settings for a CD-ROM is stored even if the disc is remove and will be immediately available if the disc is reinserted.
hp.book Page 9 Thursday, April 2, 1998 4:33 PM Security Management in Specific Network Environments Access Restrictions in NetWare Bindery (no Authentication) When accessing the CD-ROM server, if user authentication is not required, then NetWare server licenses are also not required because the server does not log onto the file server. In this case, you do not have to specify the parameter AuthenticationServer stored in the CD-ROM server’s config.txt file.
hp.book Page 10 Thursday, April 2, 1998 4:33 PM Access Restrictions in NetWare Bindery (with Authentication) If user access control is required, you must define an AuthenticationServer. The CD-ROM server must log onto the authentication server briefly to authenticate the user and identify the groups the user belongs to. In this case, the authentication server must have a standby license for the CD-ROM server, but several CD-ROM servers can share this license.
hp.book Page 11 Thursday, April 2, 1998 4:33 PM Example 1: Grant all NetWare users access: NetWareUser/Group = * Example 2: Grant access to all users in the group ‘salesdep’ and to the user ‘Daryl’ who is not a member of ‘salesdep’: NetWareUser/Group = salesdep NetWareUser/Group = Daryl Note ❏ You can always access the CD-ROM server using the user name ‘supervisor’ and the password specified by the parameter SupervisorPassword. The factory default password is pass.
hp.book Page 12 Thursday, April 2, 1998 4:33 PM The CD-ROM server’s file system security rights are set up by the NetWare Administrator, as detailed below: 1. Login as Admin, and start the NetWare Administrator. 2. Browse the SYS: volume by double clicking it. You will see all the directories available in the CD-ROM server. 3. Select the directory or file for which you wish to set the access rights to, and right click it. 4. Choose Details, and make the required changes.
hp.book Page 13 Thursday, April 2, 1998 4:33 PM Example 2: Grant all Microsoft Networks users access: SMBPassword = * Access Restrictions in UNIX (NFS) When accessing the CD-ROM server using NFS, you may restrict the access to users with a certain IP Address, Group ID (GID) or User ID (UID). Access is controlled by creating or editing NFSIPAddress, NFSGroup and NFSUser entries in the access control files in the Volumes folder on the CD-ROM server.
hp.book Page 14 Thursday, April 2, 1998 4:33 PM Example 1: Give access to users with UID 100 and 101 and to all users with GID 4: NFSUser = 100 NFSUser = 101 NFSGroup = 4 Example 2: Give users with IP address 192.124.138.60 and 192.124.138.65 access: NFSIPAddress = 192.124.138.60 NFSIPAddress = 192.124.138.65 Authentication of a PC in an NFS environment PC workstations on a UNIX network can also be authenticated.
hp.book Page 1 Thursday, April 2, 1998 4:33 PM A Troubleshooting This appendix will help you to: • • Run a diagnostic test . . . . . . . . . . . . . . . . . . . . . . . . .page A-2 Understand the meaning of the front panel indicators. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .page A-3 The remainder of this appendix deals with the following problems: Before You Begin • Errors when accessing the CD-ROM server . . . . . . .page A-5 • Problems when running CD-ROM software . . .
hp.book Page 2 Thursday, April 2, 1998 4:33 PM Diagnostic Test The diagnostic test will test the CD-ROM server’s memory and the operation of the connected drives. Before using the diagnostic test: • Users who are currently accessing the CD-ROM server will be interrupted. • The diagnostic test is only available for the first hour after you power on or restart the CD-ROM server. Also, you must restart the CD-ROM server before you can repeat the diagnostic test.
hp.book Page 3 Thursday, April 2, 1998 4:33 PM http:///config/html/diag.htm Example Diagnostic Result The Front Panel Indicators The front panel indicators show the status of the CD-ROM server. The indicators have the following functions: • Status – Flashes during start-up. When the CD-ROM server is ready for use, this light turns OFF. The LED should remain off, unless an error condition occurs. • CD – Will turn ON when a readable CD-ROM is inserted into any connected drive.
hp.book Page 4 Thursday, April 2, 1998 4:33 PM Normal Conditions The Power LED is controlled by hardware and is always on when power is connected. See the following table to interpret the state of other LEDs. Event Status LED CD LED Network LED Initial power to unit ON ON ON During power-up/Self-test. Approx. 30 seconds.
hp.book Page 5 Thursday, April 2, 1998 4:33 PM Status Indicator Remains Lit If the Status indicator remains on after start-up, this may indicate an error. Most likely there is a problem with the SCSI bus or a connected CD-ROM drive. Turn power off and check all SCSI cable connections. Make sure all connected drives have unique SCSI addresses and that only the last drive in the SCSI chain is terminated. For the stand-alone module, restore power to the drives and then to the CD-ROM server.
hp.book Page 6 Thursday, April 2, 1998 4:33 PM CD-ROM Software will not run • If you have successfully inserted a CD-ROM, but software on the CD-ROM fails to run or generates error messages, the software may expect the CD-ROM data to be mapped at root level. In the Microsoft and IBM network operating system environments, you must then assign a drive letter to that particular disc. See chapter 4, “Mounting or Mapping Network Drives”.
hp.book Page 7 Thursday, April 2, 1998 4:33 PM A summary of the possible error messages is given below: Error Description Installation failed: NDS tree not found The server could not find the NDS tree. Please check the spelling. Installation failed: Administrator object missing The server could not find the user object specified in the NDSAdminName parameter. Please check the spelling.
hp.book Page 8 Thursday, April 2, 1998 4:33 PM Problems When Accessing Disc Changers Note ❏ Disc changers, with up to 8 discs each, are supported. Up to 56 CD-ROM discs are supported through LUN (Logical Unit Number) addressing. The CD-ROM server has a parameter, JukeBoxLockTime, which sets how long a user has exclusive access to a CD-ROM during a data-read operation.
hp.book Page 9 Thursday, April 2, 1998 4:33 PM Restoring Factory Default Settings The factory default settings can be restored if required (for example, if you have accidently disabled all network protocols). Restoring the settings can be done in three ways: • Using a Web browser on a TCP/IP network. • • Using FTP on a TCP/IP network. Using the config.ini file in a text editor • Using the Push button. Step by step instructions for each method are given below.
hp.book Page 10 Thursday, April 2, 1998 4:33 PM Using a Text Editor Follow the steps below to restore the default settings: 1. Locate and open the CD-ROM server’s config.ini file using a text editor (for example, Windows Notepad). 2. Change the FactoryDefaults parameter from no to yes. 3. Save the file. This writes the contents of the file to the CD-ROM server and will reset the server to factory defaults. Using the Push Button Follow the steps below to restore the default settings: 1.
hp.book Page 1 Thursday, April 2, 1998 4:33 PM B The Config.ini File Parameter name Default Value Description HardwareAddress = 00:60:b0:11:00:86 The CD-ROM server LAN hardware (MAC) address. The value shown is an example only. You can also set a Locally Administrated Address.
hp.book Page 2 Thursday, April 2, 1998 4:33 PM Parameter name Default Value Description BOOTPEnable = yes Enable or disable bootp IP address setup. RARPEnable = yes Enable or disable rarp IP address setup. DHCPEnable = no Enable or disable dhcp IP address setup. EnableNetBEUI = yes Enable or disable SMB over NetBIOS/NetBEUI. EnableNBT = yes Enable or disable SMB over NetBIOS/TCP/IP. [SMB] EnableWINS = yes Enable or disable WINS over NetBIOS/TCP/IP.
hp.book Page 3 Thursday, April 2, 1998 4:33 PM Parameter name Default Value Description = pass Specifies the community that has read-write access to all supported SNMP objects except read only objects. It corresponds to the writeCommunity SNMP object. TrapDestination = 0.0.0.0 Specifies the Internet Address which SNMP traps are sent to. It corresponds to the trapAddress SNMP object. Default is 0.0.0.0, i.e. all SNMP traps are disabled.
hp.book Page 4 Thursday, April 2, 1998 4:33 PM Parameter name Default Value Description NDSServerContext* = Context in the NDS Tree where you wish to install the server. NDSAdminName* = Name of user or administrator with Supervisor or Create rights in the context where you want to install the server. NDSAdminPassword* = Password for the administrator defined in NDSAdminName.
hp.book Page 5 Thursday, April 2, 1998 4:33 PM TimeZone parameter permissible values The following table shows the time zone as the number of hours +/-UTC (Universal Coordinated Time or Greenwich Mean Time) • If you use the parameter values shown on the left, there will be no automatic adjustment for DST (DST = Daylight Saving Time). • If you use the parameter values shown on the right, DST adjustments are automatic.
hp.book Page 6 Thursday, April 2, 1998 4:33 PM TimeZone parameter value B-6 The Config.
hp.book Page 1 Thursday, April 2, 1998 4:33 PM C Updating the Firmware Firmware Updates The CD-ROM server firmware stored in Flash Memory* on the server can easily be updated over the network. All firmware updates are free of charge. Note ❏ *Flash Memory The program (firmware) that runs your CD-ROM server is stored in Flash Memory. This is a memory chip that, like ordinary ROM memory, keeps its contents even when the power is turned off. However, you can erase its contents and write new data to it.
hp.book Page 2 Thursday, April 2, 1998 4:33 PM Follow the steps below to install new CD-ROM server firmware: 1. Obtain a copy of the firmware update file from your HP-authorized dealer or from HP’s Electronic Support services. 2. Log in to the CD-ROM server with the command ftp where is the IP address or host name assigned to your CD-ROM server. 3. You will be prompted for user id and password.
hp.book Page 1 Thursday, April 2, 1998 4:33 PM D Technical Specifications All specifications are subject to change without prior notice. General • Height: 1.7 in (4.3 cm) Dimensions • Width: 5.9 in (14.9 cm) • Depth: 8.8 in (22.4 cm) Weight • 1.5 lbs (0.7 kg) • 32-bit RISC controller Internal Components • 2 Mbytes RAM • 2 Mbytes flash memory for firmware updates. Firmware Updates (Flash memory allows you to download the latest firmware to update your CD-ROM server operation.
hp.book Page 2 Thursday, April 2, 1998 4:33 PM Network and Drive Connectors Stand-Alone Module Tower Module • RJ-45 (10Base-T twisted-pair cables) • RJ-45 (10Base-T twisted-pair cables) Network • BNC (10Base2 ThinLAN coaxial cables) • AUI (10Base2, 10Base5, or fiber-optic transceiver) CD-ROM Drive SCSI-2, 50-pin female, high-density (micro-D). SCSI-2, 50-pin header (typically, for ribbon cable).
hp.
hp.book Page 4 Thursday, April 2, 1998 4:33 PM Supported Network Protocols Novell NetWare: NCP over IPX Microsoft Windows and OS/2 SMB over NetBIOS/NetBEUI and SMB over NetBIOS/TCP/IP TCP/IP NFS over UDP/IP, TCP, ARP, RARP, BOOTP, DHCP, WINS/NBNS, SNMP, FTP WWW HTTP over TCP/IP Network Management SNMP MIB-II and private enterprise MIB. Platform-independent configuration and management through standard Web browser.
hp.book Page 1 Thursday, April 2, 1998 4:33 PM E Warranty Your Authorized Dealer If you encounter difficulty, begin by contacting your HP Authorized Dealer who sold this product to you. Your HP Authorized Dealer will be familiar with your requirements and can provide assistance. Customer Support Hewlett-Packard has support services available to help you in case of difficulties with your HP HP CD-ROM Server. For postsales support, refer to the telephone numbers in the front of this guide.
hp.book Page 2 Thursday, April 2, 1998 4:33 PM Service Billing (Out of Warranty) When ordering a replacement unit for out-of-warranty service, you may be charged a repair cost. See your HP Authorized Dealer or your local HP Sales and Service Office representative. Or, you can call HP at (800) 366-8040 (USA only).
hp.book Page 1 Thursday, April 2, 1998 4:33 PM F Regulatory Statements FCC Statements General Information This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Pursuant to Part 15.
hp.book Page 2 Thursday, April 2, 1998 4:33 PM • • Australia Canada Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. This equipment complies with Australian EMC requirements. This equipment complies with Canadian EMC Class-A requirements.
hp.
hp.
hp.book Page 1 Thursday, April 2, 1998 4:33 PM Index ! C 10Base2 2-9, D-2 10Base5 2-9, D-2 10Base-T 2-9, D-2 Cables SCSI 2-3 CD drive access 4-5 CD folder 4-2 CD LED indicator 2-10, A-3 CD-ROM Access control 6-2 Accessing 4-5 Alias 6-2 Folder 4-4 Inserting 4-2 Map to drive letter 4-5 User limit 6-2, 6-3 CompuServe 8 Config folder 4-4, 5-4 Config.
hp.book Page 2 Thursday, April 2, 1998 4:33 PM G N GID 6-13 NBT 4-12 NCP 4-1, 4-6 Net mask 3-8 NetWare 4-6 Authentication Server 6-9 Loginscripts 4-6 Server name 4-6 Supervisor 6-11 Supervisor password 6-11 NetWare NDS 3-1, 6-11 NetWareUser/Group 6-10 Network connector board 2-6 Network indicator A-3 NFS 4-1, 4-21, 4-22, 6-13 NFSGroup 6-13 NFSIPAddress 6-13 NFSUser 6-13 NLM 1-3 Node address. See LAN hardware address.
hp.book Page 3 Thursday, April 2, 1998 4:33 PM S U SCSI Address 2-7, 4-4 Cables 2-3 Chain 2-8 Guidelines 2-7 Terminator 2-3, 2-8 SCSI folder 4-4 SCSI.txt file 4-4 SCSIAlias 4-3, 4-5 Security Management Text Editor 6-6 Web Browser 6-3 Server folder 4-4 Server name NetWare 4-6 SMB 4-12, 5-1 SessionTimeout 6-3 Share-level access control 6-12 SMB 4-1, 4-12 Over NetBIOS/NetBEUI 5-1 Over NetBIOS/TCP/IP 5-1 Server name 4-12 SMB server name 4-12, 5-1 SMBPassword 6-12 SNMP 5-1 Stat.
hp.
hp.
hp.