LASERJET PROFESSIONAL P1100/P1560/P1600 SERIES PRINTERS Software Technical Reference Additional product information: www.hp.com/support/ljp1100series www.hp.com/support/ljp1560series www.hp.
HP LaserJet Professional P1100/P1560/ P1600 Series Printer Software Technical Reference
Copyright and license Trademark Credits ©2010 Copyright Hewlett-Packard Development Company, L.P. Adobe®, Acrobat® and PostScript® are trademarks of Adobe Systems Incorporated. Reproduction, adaptation or translation without prior written permission is prohibited, except as allowed under the copyright laws. Corel® is a trademark or registered trademark of Corel Corporation or Corel Corporation Limited. The information contained herein is subject to change without notice.
Table of contents 1 Purpose and scope ......................................................................................................................................... 1 Introduction ........................................................................................................................................... 2 Product comparison ............................................................................................................................. 3 Product features ..............
More Information .............................................................................. 35 2 Software description .................................................................................................................................... 37 Windows printing-system software ..................................................................................................... 38 Supported operating systems for Windows .......................................................................
Install the print driver from the CD for wireless network connected products .......................................................................................................... 124 Install the product on a secure wireless network ............................ 124 Install the print driver on a non-secure network .............................. 158 Install the print driver from the CD to print to a previously configured wireless network printer ............................................................
Source is ......................................................................................................... 210 Type Is ............................................................................................................ 211 Document preview image ................................................................................................ 211 Print Quality .....................................................................................................................
Print Density .................................................................................................................... 233 Auto-Off Console ............................................................................................................. 233 5 Macintosh software and utilities ............................................................................................................... 235 Introduction ..................................................................................
viii ENWW
List of tables Table 1-1 HP LaserJet Professional P1100 Series Printer ................................................................................ 7 Table 1-2 HP LaserJet Professional P1560 Series Printer ................................................................................ 8 Table 1-3 HP LaserJet Professional P1100 Series Printer .............................................................................. 12 Table 1-4 HP LaserJet Professional P1560 Series Printer ........................
x ENWW
List of figures Figure 1-1 HP LaserJet Professional P1100 Series Printer ............................................................................... 7 Figure 1-2 HP LaserJet Professional P1100 Series Printer (wireless) ............................................................... 8 Figure 1-3 HP LaserJet Professional P1560 Series Printer/HP LaserJet Professional P1600 Series Printer .......................................................................................................................
Figure 3-19 Figure 3-20 Figure 3-21 Figure 3-22 Figure 3-23 Figure 3-24 Figure 3-25 Figure 3-26 Figure 3-27 Figure 3-28 Figure 3-29 Figure 3-30 Figure 3-31 Figure 3-32 Figure 3-33 Figure 3-34 Figure 3-35 Figure 3-36 Figure 3-37 Figure 3-38 Figure 3-39 Figure 3-40 Figure 3-41 Figure 3-42 Figure 3-43 Figure 3-44 Figure 3-45 Figure 3-46 Figure 3-47 Figure 3-48 Figure 3-49 Figure 3-50 Figure 3-51 Figure 3-52 Figure 3-53 Figure 3-54 Figure 3-55 Figure 3-56 Figure 3-57 Figure 3-58 Figure 3-59 Figure 3-60 Figure 3
Figure 3-63 Figure 3-64 Figure 3-65 Figure 3-66 Figure 3-67 Figure 3-68 Figure 3-69 Figure 3-70 Figure 3-71 Figure 3-72 Figure 3-73 Figure 3-74 Figure 3-75 Figure 3-76 Figure 3-77 Figure 3-78 Figure 3-79 Figure 3-80 Figure 3-81 Figure 3-82 Figure 3-83 Figure 3-84 Figure 3-85 Figure 3-86 Figure 3-87 Figure 3-88 Figure 3-89 Figure 3-90 Figure 3-91 Figure 3-92 Figure 3-93 Figure 3-94 Figure 3-95 Figure 3-96 Figure 3-97 Figure 3-98 Figure 3-99 Figure 3-100 Figure 3-101 Figure 3-102 Figure 3-103 Figure 3-104 Fig
Figure 3-107 Software Installation — Initial screen ................................................................................... 159 Figure 3-108 Choose Easy Install or Advanced Install screen ....................................................................... 160 Figure 3-109 Select Printer ............................................................................................................................ 161 Figure 3-110 Printer Connections screen .......................................
Figure 4-9 Figure 4-10 Figure 4-11 Figure 4-12 Figure 4-13 Figure 4-14 Figure 4-15 Figure 4-16 Figure 5-1 Figure 5-2 Figure 5-3 Figure 5-4 Figure 5-5 Figure 5-6 Figure 5-7 Figure 6-1 Figure 6-2 ENWW Finishing tab ............................................................................................................................... 220 Print on Both Sides Instructions dialog box ............................................................................
xvi ENWW
1 ENWW Purpose and scope 1
Introduction This software technical reference (STR) provides information about and troubleshooting tips for the printing-system software for the product. This STR is prepared in an electronic format to serve as a quick-reference tool for Customer Care Center (CCC) agents, support engineers, system administrators, management information systems (MIS) personnel, and end users, as appropriate.
Product comparison HP LaserJet Professional P1100 Series Printer printer (base model) HP LaserJet Professional P1100 Series Printer printer (wireless) ENWW ● Speed: Up to 18 A4 pages per minute (ppm), 19 letter-size ppm ● Tray: 150-sheet input tray ● Connectivity: Hi-Speed USB 2.0 port ● Duplexing: Manual duplexing (using the printer driver) Has the same features as the HP LaserJet Professional P1100 Series Printer, with the following additions.
HP LaserJet Professional P1560 Series Printer printer (Lite) ● Speed: 22 A4 pages per minute (ppm), 23 letter-size ppm ● Trays: Priority input slot (10-sheet) and a main-input tray (250-sheet) ● Output bin: 125-sheets ● Connectivity: Hi-Speed USB 2.
Product features Benefit Supporting features Excellent print quality ● Genuine HP print cartridge. ● FastRes 600 setting (P1100 series) and 600 dots per inch (dpi) setting (P1560/P1600 series) effective print quality. FastRes 1200 setting provides 1,200 dpi effective print quality. ● Adjustable settings to optimize print quality.
Benefit Supporting features Accessibility ● The online user guide is compatible with text screen-readers. ● All doors and covers can be opened by using one hand. ● Kensington lock receptacle on the back of the product.
Product views Front and left side view Figure 1-1 HP LaserJet Professional P1100 Series Printer 1 2 7 3 6 5 4 Table 1-1 HP LaserJet Professional P1100 Series Printer ENWW 1 Output bin 2 Foldable output tray extension 3 Input tray 4 Short media extender tool 5 Power button 6 Print-cartridge door lift-tab 7 Control panel Product views 7
Figure 1-2 HP LaserJet Professional P1100 Series Printer (wireless) 1 2 7 3 6 5 4 Table 1-2 HP LaserJet Professional P1560 Series Printer 1 Output bin 2 Foldable output tray extension 3 Priority input slot 4 Main input tray 5 Power button 6 Print-cartridge door lift-tab 7 Control panel Figure 1-3 HP LaserJet Professional P1560 Series Printer/HP LaserJet Professional P1600 Series Printer 1 2 7 3 4 6 5 1 8 Output bin Chapter 1 Purpose and scope ENWW
ENWW 2 Output tray extension 3 Priority input slot 4 Main-input tray 5 Power button 6 Cartridge door lift-tab 7 Control panel Product views 9
Back view Figure 1-4 HP LaserJet Professional P1100 Series Printer 1 3 2 1 USB port 2 Power connector 3 Kensington lock Figure 1-5 HP LaserJet Professional P1560 Series Printer/HP LaserJet Professional P1600 Series Printer 1 3 4 2 1 USB port HP internal network port (HP LaserJet Professional P1560 Series Printer only) 10 2 Power receptacle 3 Kensington lock 4 Duplexer and rear jam-access door (HP LaserJet Professional P1600 Series Printer series only) Chapter 1 Purpose and scope ENWW
Serial number and product number location The label that contains the product number and serial number is on the rear of the product.
Control-panel layout Figure 1-7 HP LaserJet Professional P1100 Series Printer 1 2 Table 1-3 HP LaserJet Professional P1100 Series Printer 1 Attention light: Indicates that the print cartridge door is open or other errors exist. 2 Ready light: When the product is ready to print, the ready light is on. When the product is processing data, the ready light blinks.
Figure 1-9 HP LaserJet Professional P1560 Series Printer/HP LaserJet Professional P1600 Series Printer 1 2 3 4 5 6 1 Toner light : When the print cartridge is low, the toner light product, the toner light 2 3 4 5 Attention light : Indicates that the print-cartridge door is open or other errors exist. Ready light : When the product is ready to print, the ready light blinks. Go button ENWW is on.
Printing-system software ● Operating-system support ● Availability and localization Operating-system support Windows operating systems provide full-featured support for the product. Operating systems that are not described in this STR provide varying levels of functionality. Throughout this document, Windows XP is used to denote Windows XP Home Edition and Windows XP Professional, unless noted otherwise. Information relating to networking functions is specific to products that have network capabilities.
Supported operating systems for Windows The product comes with software for the following Windows® operating systems: ● Windows Vista (32-bit and 64-bit) ● Windows XP (32-bit and 64-bit) ● Windows 7 (32-bit and 64-bit) ● Windows Server 2003 (32-bit and 64-bit) For more information about upgrading from Windows 2000 Server to Windows Server 2003, using Windows Server 2003 Point and Print, or using Windows Server 2003 Terminal Services and Printing, go to www.microsoft.com.
Drivers downloaded from the “Driver” section are wrapped with the HP DIU (Driver Installation Utility) and produce a “named” driver when installed. A named driver has the printer model number in the driver print queue name. These drivers always install in Traditional mode. Drivers downloaded from the “Driver-Universal Print Driver” section includes the UPD installer. For these drivers, the driver print queue shows a non-product-specific name.
Supported utilities for Macintosh The following additional software is available for Macintosh for use with the HP LaserJet Professional P1100/P1560/P1600 Series Printer printer. HP LaserJet Utility Use the HP LaserJet Utility to set up product features that are not available in the printer driver. You can use the HP LaserJet Utility when the product is connected with a universal serial bus (USB) cable.
NOTE: This STR describes drivers that are included in the product firmware and are also shipped with the printing-system software CD. This document does not describe any drivers that might be released by support personnel.
The printing-system software is available for download at the following Web sites: www.hp.com/support/ljp1100series www.hp.com/support/ljp1560series or www.hp.com/go/ljp1600series The PCL 5e Universal Print Driver (P1600 series only) is available for download at the following Web site: hp.com/go/upd In-box printing-system software CD One CD is included in-box with the product.
● ET = Estonian (Eesti) ● FI = Finnish (Suomi) ● FR = French (Français) ● HE = Hebrew ● HR = Croatian (Hrvatski) ● HU = Hungarian (Magyar) ● ID = Indonesia (Bahasa) ● IT = Italian (Italiano) ● KK = Kazakh ● KO = Korean ● LT = Lithuanian ● LV = Latvian ● NL = Dutch (Nederland) ● NO = Norwegian (Norsk) ● PL = Polish (Polski) ● PT = Brazilian Portuguese (Português) ● RO = Romanian ● RU = Russian (Russ) ● SK = Slovak ● SL = Slovenian ● SR = Serbian ● SV = Swedish (Sven
Table 1-8 Supported printing-system components (AR-ET) (continued) Component AR BG CA CS DA DE EL EN ES ET HP Smart Install x x x x x x x x x x Mac Installer x x x x Mac OS X PS Driver (PPD and PDEs) x x x x x x x x Printer Driver (Mac) x x x x HP LaserJet Utility (Mac) x x x x Install Notes – Windows (HTML) x x x x x x User Guide (CHM, PDF) x x x x x x x x x x HP LaserJet Help Navigation x x x x x x x x x x x x x x Web Registrat
Table 1-10 Supported printing-system components (LV-SL) (continued) Component NL NO Mac Installer x x x Mac OS X PS Driver (PPD and PDEs) x x x x x Printer Driver (Mac) x x x HP LaserJet Utility (Mac) x x x Install Notes – Windows (HTML) LV x PL PT x x RO RU SK SL x x x x User Guide (CHM, PDF) x x x x x x x x x HP LaserJet Help Navigation x x x x x x x x x x x x x Web Registration x Table 1-11 Supported printing-system components (SR-ZHT) Compone
Documentation The printing-system software CD that is included with the product contains documentation. Access to the documents depends on the document type and location as follows: ● Some documents can be opened from the CD Browser. ● Some documents appear on the CD and can only be opened by navigating to the folder where they reside. ● Some documents are available on the Web through links in the CD Browser or CD folders.
Printing-system software CD ● Main CD browser screen ● User Documentation Main CD browser screen To view documentation and use links to HP support on the printing-system software CD, insert the CD into the into the CD-ROM drive. The main screen of the CD Browser opens. Move the cursor over each option to see a description of the option in the right panel.
User Documentation On the main screen of the printing-system software CD Browser, click View User Guide to open the View User Guide screen. Move the cursor over each option to see a description of the option in the right panel. Figure 1-11 View User Guide screen ● HP LaserJet Help Navigation ● User Guide ● More Information HP LaserJet Help Navigation General instructions Click either the P1100 Series button or the P1560/P1600 Series button to open the HP LaserJet Help Navigation application.
Click Browse User Guide to gain access to the product user guide. ● If the product software is installed by a direct USB connection and not from the CD, the user guide is not installed locally on your computer as part of the installation. Click the Open the latest version on the web link to download and view the user guide from www.hp.com. ● If the product software is installed from the CD, click Open the user guide on my computer to open the locally installed version of the user guide.
◦ Print on pre-printed letterhead or forms ◦ Print on special paper ◦ Print the first or last page on different paper Click the Manage & Maintain button to gain quick access to the following sections of the user guide. ● Print information pages ● Replace a print cartridge ● Print a cleaning page ● Change energy settings Click the Solve a Problem button to gain quick access to the following sections of the user guide.
Table 1-13 Control-panel light patterns (continued) 28 Light status State of the product Action Status lights cycle The status lights cycle during the formatter initialization period or when the product is processing a cleaning page. No action is required. Wait for the initialization period to end. The product enters the ready state when the initialization period is finished. Ready light is on, and attention light is off. The product is in the ready state. No action is required.
Table 1-13 Control-panel light patterns (continued) Light status State of the product Action Attention light is blinking, and ready light is on. The product has experienced a continual If the recovery is successful, the product error from which it can recover on its own. continues to the processing data state and completes the job. If the recovery is unsuccessful, the product continues to the continuable error state.
Table 1-13 Control-panel light patterns (continued) Light status State of the product Action The wireless light is on. The product is connected to a wireless network. No action is required. The wireless light is off. The product is not connected to a network, and the wireless unit in the product might be turned off. If the light is off, the product is not connected to the network and the wireless unit in the product might be off.
Table 1-14 Status-light legend (continued) Symbol for “light on” Symbol for “light blinking” Table 1-15 Control-panel lights Light status All lights are off NOTE: is off. The power button backlight All lights are off NOTE: is on. The power button backlight Light pattern State of the product Action The product is in Auto-Off mode or is turned off. Press the power button to deactivate the Auto-Off mode or turn on the product The formatter is not connected to the product correctly. 1.
Table 1-15 Control-panel lights (continued) Light status Attention Light pattern , ready , and go lights cycle. Toner light NOTE: is on. is off. The power button backlight Ready light lights are off. NOTE: is on. is on, and all other The formatter is initializing. No action required. Wait for the initialization period to end. The product enters the Ready state when the initialization period is finished. The product is processing a cleaning page. No action required.
Table 1-15 Control-panel lights (continued) Light status Attention light Light pattern is blinking, and all other lights are off. NOTE: is on. The power button backlight Attention light light NOTE: is on. is blinking, ready is on, and other lights are off. The power button backlight State of the product Action The product has experienced an error that can be corrected at the product, such as a jam, an open door, or the absence of paper in the proper tray.
Table 1-15 Control-panel lights (continued) Light status The ready Light pattern and toner lights are on. NOTE: is on. Action The print cartridge is near the estimated end of life. Order a new print cartridge and have it ready. The print cartridge has been removed from the product. Reinsert the print cartridge in the product. The power button backlight Toner light NOTE: is on. State of the product is blinking.
NOTE: The "xx" in the file name corresponds to the language. For French, the file name is LJP1100_use_frww.CHM. Open the .PDF file (Mac) from the printing-system software CD directory as follows: 1. Insert the printing-system software CD into the CD-ROM drive. 2. Double-click the Documentation folder. 3. Open either of the following files. LJP1100_use_xxww.pdf or LJP1560-LJP1600_use_xxww.pdf NOTE: For information about which languages are supported, see Tables 8-11 in this chapter.
Install Notes The HP LaserJet Professional P1100/P1560/P1600 Series Printer Printing-System Install Notes (.HTM) contains important information about device features, instructions for installing the printing-system software, and technical assistance. Open the install notes from the printing-system software CD Browser as follows: 1. On the main screen of the CD Browser, click More Information. 2. Click Install Notes. Open the .HTM file directly: 1.
2 ENWW Software description ● Windows printing-system software ● Embedded Web Server 37
Windows printing-system software ● Supported operating systems for Windows ● Windows operating system requirements ● Macintosh system requirements ● Printer driver ● Select the correct printer driver for Windows ● Priority for print settings ● Change printer-driver settings for Windows ● Printing system and installer ● Driver version numbers for Windows operating systems Supported operating systems for Windows The product supports the following Windows operating systems: ● Windows XP (32-
● ◦ CD-ROM drive ◦ USB Windows 7 (32-bit and 64-bit) ◦ 1 GB RAM ◦ 350 MB HD free space ◦ CD-ROM drive ◦ USB Macintosh system requirements The HP printing-system software has the following minimum system requirements for the Mac OS X V10.4, V10.5, and V10.6. ● 256 MB RAM ● 150 MB HD free space ● CD-ROM ● USB NOTE: PPC and Intel® Core Processor Macs are supported.
Priority for print settings Changes to print settings are prioritized depending on where the changes are made. NOTE: The names of commands and dialog boxes might vary depending on your software program. ● Page Setup dialog box: Click Page Setup or a similar command on the File menu of the program you are working in to open this dialog box. Settings changed here override settings changed anywhere else.
Printing system and installer The printing-system files and installers come in both the product firmware and on CD. The recommended installation method for the printing-system files is via a direct USB connection between the product and computer using HP Smart Install. ● HP Smart Install ● Printing-system software CD for Windows systems HP Smart Install The HP LaserJet Professional P1100/P1560/P1600 Series Printer products come with HP Smart Install loaded in their firmware.
In supported Windows operating systems, insert the printing-system CD in the CD-ROM drive to open an interactive CD Browser. Use the CD Browser to install the drivers and related components and to gain access to online user documentation, a customization utility, and optional HP software. Figure 2-2 Installation software CD Browser If the screen does not appear when you insert the printing-system CD into the CD-ROM drive, follow these steps to open the CD Browser: 1. Click Start. 2. Click Run. 3.
Driver version numbers for Windows operating systems Access to driver version numbers varies, depending on the operating system in which the printing system is installed. NOTE: For a list of product drivers, updated HP printing-system software, and product-support information, go to: www.hp.com/support/ljp1100series www.hp.com/support/ljp1560series or www.hp.com/go/ljp1600series In supported Windows operating systems, follow these steps to find driver-version information: 1.
Embedded Web Server LJP1102w and P1606 series are equipped with the HP Embedded Web Server (HP EWS), which provides access to information about product and network activities. This information appears in a Web browser, such as Microsoft Internet Explorer, Apple Safari, or Firefox. The HP EWS resides on the product. It is not loaded on a network server. The HP EWS provides an interface to the product that anyone who has a network-connected computer and a standard Web browser can use.
3 Install Windows printing-system components The HP LaserJet Professional P1100/P1560/P1600 Series Printer comes with software and installers for Microsoft Windows and Apple Macintosh systems. For information about Macintosh software, see Macintosh software and utilities on page 235 This chapter provides procedures for installing and uninstalling the HP LaserJet Professional P1100/P1560/P1600 Series Printer printing-system software for Windows operating systems.
Supported operating systems for Windows The HP LaserJet Professional P1100/P1560/P1600 Series Printer printer supports the following Windows operating systems: ● Windows XP (32-bit and 64-bit) ● Windows Server 2003 (32-bit and 64-bit) ● Windows Vista (32-bit and 64-bit) ● Windows Server 2008 (32-bit and 64-bit) ● Windows 7 (32-bit and 64-bit) Windows operating system requirements The HP printing-system software has the following minimum system requirements for the following Windows operating syste
For all supported operating systems, each install option presents a series of screens that guide you through the installation process. Software installation types for Windows The HP LaserJet Professional P1100/P1560/P1600 Series Printer printing-system software can be installed in the following ways: ● HP Smart Install: Recommended, included in the product firmware. HP Smart Install starts automatically when the product is connected to a computer by USB.
Microsoft Windows general installation overview HP LaserJet Professional P1100/P1560/P1600 Series Printer printingsystem software for Windows systems HP LaserJet Professional P1100/P1560/P1600 Series Printer printing-system software can be installed either via a direct USB connection to the product or from the printing-system software CD HP Smart Install NOTE: This installation type is supported for Windows only.
figure shows the main screen of the HP LaserJet Professional P1100/P1560/P1600 Series Printer printing-system software CD. Figure 3-1 CD Browser – Main screen Click Install to start the CD installer. By default, the CD installer installs the HP LaserJet Professional P1100/P1560/P1600 Series Printer Host-based print driver, the driver recommended for most users.
Follow these instructions to select the correct connection option: 1. On the Start menu, click the Settings option, and then perform one of the following: Windows XP Home: Click the Printers and Other Hardware Devices option. Windows XP Professional, Windows Server 2003, and Windows 2008: Click the Printers and Faxes option. Windows Vista: Under the Hardware and Sound category, click the Printer option. Windows 7: Click the Devices and Printers option. 2. Click the Add a printer option.
Use an existing port for a direct connection Use these instructions when the product is connected to the computer using a USB cable or when printing via the network without using a print server. 1.
2. (Optional) Click the Windows Update button to display a list of drivers that can be downloaded from the Microsoft Windows Update Web site. If the appropriate model of HP LaserJet Professional P1100/P1560/P1600 Series Printer is already listed, select it and click the Next > button. If the product is not listed, click the Have Disk button to continue to the Install From Disk screen. Figure 3-4 Add Printer Wizard — Install Printer Software screen 3.
6. Select the appropriate model of HP LaserJet Professional P1100/P1560/P1600 Series Printer from the list and click the Next > button to continue to the Name Your Printer screen.
7. You can either type a name for the product in the Printer name text box or use the default name provided. Select the Yes option to use this printer as the default printer or select the No option to keep the existing product as the default printer. Click the Next > button to continue to the Printer Sharing screen.
8. Select either the Do not share this printer option, or select the Share name: option and type share name, and then click the Next > button to continue to the Print Test Page screen. Figure 3-8 Add Printer Wizard — Printer Sharing screen 9. Select the Yes option if you want to print a test page after the software is installed. Select the No option if you do not want to print a test page after the software is installed. Click the Next > button to continue to the Completing the Add Printer Wizard screen.
Create a new TCP/IP port for a direct connection Perform the following when the product is connected via the network without using a print server and a printer port does not exist: 1. If the printer port does not appear in the Use the following port drop-down list, select the Create a new port option. ● If the Advanced TCP/IP Port Monitor option appears in the Type of port drop-down list, select this option, and then click the Next button.
2. Click the Next > button.
3. Type the product's IP address or host name in the Printer Name or IP Address text box, and then click the Next button. NOTE: The default port name is the name that you typed in the Printer Name or IP Address text box. You can change this name by typing a new name in the Port Name text box. NOTE: The Always print to this device, even if its IP address changes check box is only available if you select the Advanced TCP/IP Port Monitor option from the Select a Printer Port dialog box.
Print server connection Perform the following when the product is connected via the network using a print server: 1. If the product is connected via the network using a print server, select the A network printer, or a printer attached to another computer option, and then click the Next > button.
2. Select either the Find a printer in the directory option, the Connect to this printer (or to browse for a printer, select this option and click Next) option, or the Connect to a printer on the Internet or on a home or office network option, and then click the Next > button. Figure 3-14 Add Printer Wizard — Specify A Printer screen If you select the Find a printer in the directory option and then click the Next > button, you will continue to the Find Printers dialog box.
Select one of the following options: a. (Find a printer in the directory option only) Specify search attributes to find your product on the network, and then click the Find Now button to search the specified location for your product. Once the search has completed, select the product, and then click the OK button to continue to the Default Printer dialog box.
b. (Connect to this printer (or to browse for a printer, select this option and click Next) option only) Specify the print path for the product and then click the Next > button. The computer will search the network for shared products. Select the product from the list and then click the Next > button to continue to the Completing the Add Printer Wizard dialog box. Figure 3-17 Add Printer Wizard — Browse for Printer screen c.
Detailed MS Windows installation instructions The dialog boxes shown here appear in the Windows XP Professional installation sequence. The order and appearance of dialog boxes can vary among operating systems.
2. On the Printer Connections screen, select Configure to print over the Network or Configure to print using USB. Click the Next button. Figure 3-19 Printer Connections screen ▲ For product installations configured to print over the network, follow these steps. i. 64 Connect your product to the network if not already connected.
ii. The Network Connection Successful screen appears. Disconnect the USB cable from the product and then click the Next button.
3. The Congratulations! Software installation complete screen appears. Click the Next button to register your product and print a test page. Deselect Register your product or Print Test Page to continue without registering your product or printing a test page.
4. The Links to additional software screen appears. Figure 3-22 Links to additional software screen Use the links on this screen to download any of the following software for your product. ● HP Smart Web Printing ● XPS driver ● PCL5e driver (P1600 series models only) 5. Click the Finish button to complete the installation. 6. The HP LaserJet Help Navigation application appears after the installation is complete.
NOTE: Silent configuration of wireless settings is supported on the wireless router/access points listed in Supported routers for wireless products that support automatic configuration. on page 254 A series of dialog boxes appear during installation of the HP LaserJet Professional P1100/P1560/P1600 Series Printer printing-system software in Windows environments.
2. Select Configure to Print over the Wireless Network and then click the Next button.
3. On the Wireless Discovery Method dialog, select the Automatic (Recommended) option and then click the Next button. Figure 3-25 Wireless Discovery Method screen 4. The installer attempts to locate a wireless router/access point on a wireless network that the product is capable of accessing. a. 70 If the installer locates a single router/access point on the wireless network that the product is capable of accessing, a Wireless Credentials screen appears.
b. If the installer locates more than one wireless router/access point on the wireless network that the product is capable of accessing, the Networks Discovered screen appears. Select the wireless router/access point (Network Name (SSID)) to connect to on the Networks Discovered screen and then click the Next button to continue to Step 5.
c. If the installer cannot locate a wireless router/access point on the wireless network that the product is capable of accessing, the following message appears. Click the OK button to proceed. The installation mode automatically changes to the Advanced mode. See Step 4 of Advanced install on page 81 to proceed. Figure 3-27 d. 72 If the installer locates one or more wireless router/access points, but cannot log in to them, the installation mode automatically changes to Advanced mode.
5. The Wireless Credentials screen appears in the following forms depending on the security mode configured on the wireless router/access point. ● With the wireless credentials for the router/access point hidden.
● With WPA wireless credentials details displayed.
● With WEP wireless credentials details displayed.
● With no security enabled on the router/access point. Figure 3-31 Wireless Credentials screen with no security enabled on the router/access point 6. 76 Enter any credential information, if required, on the Wireless Credentials screen that appears for your installation type and then click the Next button.
7. If the connection is successful, the Network Connection Successful screen appears. Disconnect the USB cable between the computer and the product and click the Next button to proceed to Step 8.
If the connection is not successful, one of the following error message screens appears. Click the Back button on either error message screen to return to one of the Wireless Credentials screens listed in Step 5 to configure the wireless credentials again. ● If the product is connected on the network but cannot communicate with the computer, the following error message appears with the instructions to make sure the computer and the product are on the same network.
● If wireless credentials are used that the product cannot connect with, the following error message appears.
8. The Congratulations! Software installation complete screen appears upon successful installation of the driver. Figure 3-35 Software installation complete screen (part 1) 9. 80 Select Register your product and Print Test Page, and then click the Next button. A Web browser opens to the HP Product Registration page, and a test page prints at the product.
10. The Congratulations! Software installation complete screen appears with links to download HP Smart Web Printing and the XPS driver. Figure 3-36 Software installation complete screen (part 2) NOTE: For P1600 series models, the option to download the PCL5e driver appears on this screen. 11. Click the Finish button. 12. The HP LaserJet Help Navigation application opens. Advanced install The Wireless Configuration Utility (WCU) guides the user through the setup process.
NOTE: You can return to the previous dialog box by clicking Back or exit the HP LaserJet Professional P1100/P1560/P1600 Series Printer printing-system software installation by clicking Cancel wherever these options appear in the installation sequence. 1. Connect the product to the computer using a USB cable. The Welcome to HP Smart Install screen appears. Select whether to accept, or review before accepting, the software End User License Agreement, and the click the Install button.
2. Select Configure to Print over the Wireless Network and then click the Next button.
3. On the Wireless Discovery Method dialog, select the Advanced and then click the Next button.
4. If the installer finds one or more wireless router/access points on your wireless network, the Networks Discovered screen appears. Select a router/access point (Network Name (SSID))from the list, or select Enter your Network Name (SSID) manually to manually enter the SSID, and then click the Next button.
5. If the installer does not automatically find one or more wireless router/access points on your wireless network, the following screen appears for manually entering the SSID of the router/access point to connect to. Enter the SSID in the SSID: field, and then click the Next button.
6. The Wi-Fi Protected Setup screen appears with instructions for enabling WiFi Protected Setup or for entering wireless credentials manually. Figure 3-42 WiFi Protected Setup screen For automatic Wi-Fi protected configuration, follow these steps. ENWW a. Press the Wi-Fi Protected Setup (WPS) button on the router, select I have pressed the WiFi Protected Setup button on my router or access point, and then click the Next button. b.
c. If the product is connected on the network but cannot communicate with the computer, the following error message appears with the instructions to make sure the computer and the product are on the same network. Click the Back button to return to Step 4.
d. If WPS fails due to the wireless router or access point not being successfully placed in WPS mode, the following error message appears. Click the Retry button to return to Step 4 or click the Next button to enter the wireless credentials manually. Figure 3-44 Wireless Configuration Failed screen For manual configuration, follow these steps. a. ENWW Select I do not want to use Wi-Fi Protected setup. I want to enter the wireless credentials manually and then click the Next button.
b. The Wireless Credentials screen appears in the following forms. ● With the wireless credentials for the router/access point hidden.
● With WPA wireless credentials details displayed.
● With WEP wireless credentials details displayed.
● With no security enabled on the router/access point.
7. Select the wireless router/access point (Network Name (SSID)) to connect to on the Networks Discovered dialog. Click the Next button.
8. If the connection is successful, the Network Connection Successful screen appears. Disconnect the USB cable between the computer and the product and click the Next button.
9. The Congratulations! Software installation complete screen appears upon successful installation of the driver. Figure 3-51 Software installation complete screen (part 1) 10. Select Register your product and Print Test Page, and then click the Next button. A Web browser opens to the HP Product Registration page, and a test page prints at the product.
11. The Congratulations! Software installation complete screen appears with links to download HP Smart Web Printing and the XPS driver. Figure 3-52 Software installation complete screen (part 2) NOTE: For P1600 series models, the option to download the PCL5e driver appears on this screen. 12. Click the Finish button. 13. The HP LaserJet Help Navigation application opens.
NOTE: You can return to the previous dialog box by clicking Back or exit the HP LaserJet Professional P1100/P1560/P1600 Series Printer printing-system software installation by clicking Cancel wherever these options appear in the installation sequence. 1. Connect the product to the computer using a USB cable. The Welcome to HP Smart Install screen appears. Select whether to accept, or review before accepting, the software End User License Agreement, and the click the Install button.
2. Select Configure to Print over the Wireless Network if you are installing a new wireless printer and are not installing the driver for the purpose of connecting to a printer that already exists on your wireless network. Click the Next button.
3. On the Wireless Discovery Method dialog, select Automatic (Recommended) to allow HP Smart Install to automatically locate your wireless router or access point. Click the Next button. Figure 3-55 Wireless Discovery Method screen NOTE: Selecting Advanced on the Wireless Discovery Method dialog allows you to manually enter your wireless network credentials.
4. Select the Network Name (SSID) to connect to on the Networks Discovered dialog. Click the Next button.
5. When HP Smart Install and the product connect via the wireless network, the Network Connection Successful screen appears. Disconnect the USB cable between the computer and the product and click the Next button.
6. The Congratulations! Software installation complete screen appears upon successful installation of the driver. Figure 3-58 Software installation complete screen (part 1) 7. ENWW Select Register your product and Print Test Page, and then click the Next button. A Web browser opens to the HP Product Registration page, and a test page prints at the product.
8. The Congratulations! Software installation complete screen appears with links to download HP Smart Web Printing and the XPS driver. Figure 3-59 Software installation complete screen (part 2) NOTE: For P1600 series models, the option to download the PCL5e driver appears on this screen. 9. Click the Finish button. 10. The HP LaserJet Help Navigation application opens. EWS Smart Install (network products) 1. Connect the product to the network and turn the power on. 2.
ENWW 4. Click the HP Smart Install tab on the EWS, and then click the Download button. 5. A download dialog window for the setup opens. Click Save File. 6. Click the Run button on the dialog window that appears.
7. The License Agreement screen appears. Select I accept the terms of the license agreement and then click the Next button.
ENWW 8. The Congratulations! Software installation complete screen appears upon successful installation of the driver. 9. Select Register your product and Print Test Page, and then click the Next button. A Web browser opens to the HP Product Registration page, and a test page prints at the product.
10. The Congratulations! Software installation complete screen appears with links to download HP Smart Web Printing and the XPS driver. 11. Click the Finish button. 12. The HP LaserJet Help Navigation application opens.
Install the Host-based driver from the CD ● Install the print driver from the CD for USB connected products ● Install the print driver from the CD for wired network connected products ● Install the print driver from the CD for wireless network connected products ● Install the print driver from the CD to print to a previously configured wireless network printer Install the print driver from the CD for USB connected products A series of dialog boxes appear during installation of the HP LaserJet Profes
c. Click OK.
3. Click Install to begin the installation process. The Choose Easy Install or Advanced Install screen appears. Figure 3-61 Choose Easy Install or Advanced Install screen The Choose Easy Install or Advanced Install screen contains links to the following information. 4. ENWW ● The software End User License Agreement – use this link to view the end user license agreement. ● The HP recommended software package – use this link to view information about the HP Customer Participation Program.
5. Select an appropriate printer model on the Select Printer screen and click the Next button. Figure 3-62 Select Printer screen NOTE: In the preceding figure, "HP LaserJet Professional P1100w Series" denotes the P1100 series wireless model.
6. Connect a USB cable between the computer and the product when prompted on the Configure to print using USB screen. Figure 3-63 Configure to print using USB screen (part 1) When the device (product) is sensed by the installer, the Configure to print using USB screen changes to display the following.
7. The Congratulations! Software installation complete screen appears upon successful installation of the driver. Figure 3-65 Software installation complete screen (part 1) 8. Select Register your product and Print Test Page, and then click the Next button. A Web browser opens to the HP Product Registration page, and a test page prints at the product.
9. The Congratulations! Software installation complete screen appears with links to download HP Smart Web Printing and the XPS driver. Figure 3-66 Software installation complete screen (part 2) NOTE: For P1600 series models, the option to download the PCL5e driver appears on this screen. 10. Click the Finish button. 11. The HP LaserJet Help Navigation application opens.
c. Click OK.
3. Click Install to begin the installation process. The Choose Easy Install or Advanced Install screen appears. Figure 3-68 Choose Easy Install or Advanced Install screen The Choose Easy Install or Advanced Install screen contains links to the following information. 4. ENWW ● The software End User License Agreement – use this link to view the end user license agreement. ● The HP recommended software package – use this link to view information about the HP Customer Participation Program.
5. Select an appropriate printer model on the Select Printer screen and click the Next button.
6. Select Configure to print over the Network and then click the Next button. Figure 3-70 Printer Connections screen 7. Select either Select from a list of detected printers (Recommended) or Specify a printer by address, and then click the Next button. If you choose to select from a list of detected printers, the installer will search your network for an HP LaserJet Professional P1600 Series Printer series printer to install and then display the Printers Found screen.
If you choose to specify a printer by address, select one of the following identification methods, enter a value for the method, and then click the Next button.
When the installer locates the printer you specified, the Printer Found screen appears. Select Yes, install this printer. or No, I want to install a different printer. Click the Next button.
8. On the Confirm Network Settings screen, click the Next button to confirm the network settings or click the Change button to modify the network settings.
9. The Congratulations! Software installation complete screen appears after successful installation of the driver. Figure 3-71 Software installation complete screen (part 1) 10. Select Register your product and Print Test Page, and then click the Next button. A Web browser opens to the HP Product Registration page, and a test page prints at the product.
11. The Congratulations! Software installation complete screen appears with links to download HP Smart Web Printing and the XPS driver. Figure 3-72 Software installation complete screen (part 2) NOTE: For P1600 series models, the option to download the PCL5e driver appears on this screen. 12. Click the Finish button. 13. The HP LaserJet Help Navigation application opens.
NOTE: Silent configuration of wireless settings is supported on the wireless routers listed in Supported routers for wireless products that support automatic configuration. on page 254 A series of dialog boxes appear during installation of the HP LaserJet Professional P1100/P1560/P1600 Series Printer printing-system software in Windows environments.
3. Click Install to begin the installation process. The Choose Easy Install or Advanced Install screen appears. Figure 3-74 Choose Easy Install or Advanced Install screen The Choose Easy Install or Advanced Install screen contains links to the following information. 4. ● The software End User License Agreement – use this link to view the end user license agreement. ● The HP recommended software package – use this link to view information about the HP Customer Participation Program.
5. Select an appropriate printer model on the Select Printer screen and click the Next button.
6. Select Configure to Print over the Wireless Network if you are installing a new wireless printer and are not installing the driver for the purpose of connecting to a printer that already exists on your wireless network. Click the Next button.
7. On the Wireless Discovery Method dialog, select Automatic (Recommended) to allow the installer to automatically locate your wireless router or access point. Click the Next button. Figure 3-77 Wireless Discovery Method screen NOTE: Selecting Advanced on the Wireless Discovery Method dialog allows you to manually enter your wireless network credentials. 8. The installer attempts to locate a wireless router/access point on a wireless network that the product is capable of accessing. a.
b. If the installer locates more than one wireless router/access point on the wireless network that the product is capable of accessing, the Networks Discovered screen appears. Select the wireless router/access point (Network Name (SSID)) to connect to on the Networks Discovered screen and then click the Next button to continue to Step 9.
c. If the installer cannot locate a wireless router/access point on the wireless network that the product is capable of accessing, the following message appears. Click the OK button to proceed. The installation mode automatically changes to the Advanced mode. See Step 8 of Advanced install on page 140 to proceed. Figure 3-79 d. ENWW If the installer locates one or more wireless router/access points, but cannot log in to them, the installation mode automatically changes to Advanced mode.
9. The Wireless Credentials screen appears in the following forms depending on the security mode configured on the wireless router/access point. ● With the wireless credentials for the router/access point hidden.
● With WPA wireless credentials details displayed.
● With WEP wireless credentials details displayed.
● With no security enabled on the router/access point. Figure 3-83 Wireless Credentials screen with no security enabled on the router/access point 10. Enter any credential information, if required, on the Wireless Credentials screen that appears for your installation type and then click the Next button.
11. If the connection is successful, the Network Connection Successful screen appears. Disconnect the USB cable between the computer and the product and click the Next button to proceed to Step 12.
If the connection is not successful, one of the following error message screens appears. Click the Back button on either error message screen to return to one of the Wireless Credentials screens listed in Step 9 and to configure the wireless credentials again. ● If the product is connected on the network but cannot communicate with the computer, the following error message appears with the instructions to make sure the computer and the product are on the same network.
● If wireless credentials are used that the product cannot connect with, the following error message appears.
12. The Congratulations! Software installation complete screen appears upon successful installation of the driver. Figure 3-87 Software installation complete screen (part 1) 13. Select Register your product and Print Test Page, and then click the Next button. A Web browser opens to the HP Product Registration page, and a test page prints at the product.
14. The Congratulations! Software installation complete screen appears with links to download HP Smart Web Printing and the XPS driver. Figure 3-88 Software installation complete screen (part 2) NOTE: For P1600 series models, the option to download the PCL5e driver appears on this screen. 15. Click the Finish button. 16. The HP LaserJet Help Navigation application opens. Advanced install The Wireless Configuration Utility (WCU) guides the user through the setup process.
2. Insert the HP LaserJet Professional P1100/P1560/P1600 Series Printer printing system software CD into the CD-ROM drive. The software installer detects the language of the operating system, and then displays the main menu of the CD Browser program in the same language. If the installer program has not started after 30 seconds, complete these steps. a. On the Start menu, click Run. b. Type the following: X:\SETUP.EXE (where X is the letter of the CD-ROM drive). c. Click OK.
3. Click Install to begin the installation process. The Choose Easy Install or Advanced Install screen appears. Figure 3-90 Choose Easy Install or Advanced Install screen The Choose Easy Install or Advanced Install screen contains links to the following information. 4. ● The software End User License Agreement – use this link to view the end user license agreement. ● The HP recommended software package – use this link to view information about the HP Customer Participation Program.
5. Select an appropriate printer model on the Select Printer screen and click the Next button.
6. Select Configure to Print over the Wireless Network if you are installing a new wireless printer and are not installing the driver for the purpose of connecting to a printer that already exists on your wireless network. Click the Next button.
7. On the Wireless Discovery Method dialog, select the Advanced and then click the Next button.
8. If the installer finds one or more wireless router/access points on your wireless network, the Networks Discovered screen appears. Select a router/access point (Network Name (SSID))from the list, or select Enter your Network Name (SSID) manually to manually enter the SSID, and then click the Next button.
9. If the installer does not automatically find one or more wireless router/access points on your wireless network, the following screen appears for manually entering the SSID of the router/access point to connect to. Enter the SSID in the SSID: field, and then click the Next button.
10. The Wi-Fi Protected Setup screen appears with instructions for enabling Wi-Fi Protected Setup or for entering wireless credentials manually. Figure 3-96 WiFi Protected Setup screen For automatic Wi-Fi protected configuration, follow these steps. a. Press the Wi-Fi Protected Setup (WPS) button on the router, select I have pressed the WiFi Protected Setup button on my router or access point, and then click the Next button. b.
c. If the product is connected on the network but cannot communicate with the computer, the following error message appears with the instructions to make sure the computer and the product are on the same network. Click the Back button to return to Step 8.
d. If WPS fails due to the wireless router or access point not being successfully placed in WPS mode, the following error message appears. Click the Retry button to return to Step 8 or click the Next button to enter the wireless credentials manually. Figure 3-98 Wireless Configuration Failed screen For manual configuration, follow these steps. a. Select I do not want to use WiFi Protected setup. I want to enter the wireless credentials manually and then click the Next button.
b. The Wireless Credentials screen appears in the following forms. ● With the wireless credentials for the router/access point hidden.
● With WPA wireless credentials details displayed.
● With WEP wireless credentials details displayed.
● With no security enabled on the router/access point.
11. Select the wireless router/access point (Network Name (SSID)) to connect to on the Networks Discovered dialog. Click the Next button.
12. If the connection is successful, the Network Connection Successful screen appears. Disconnect the USB cable between the computer and the product and click the Next button.
13. The Congratulations! Software installation complete screen appears upon successful installation of the driver. Figure 3-105 Software installation complete screen (part 1) 14. Select Register your product and Print Test Page, and then click the Next button. A Web browser opens to the HP Product Registration page, and a test page prints at the product.
15. The Congratulations! Software installation complete screen appears with links to download HP Smart Web Printing and the XPS driver. Figure 3-106 Software installation complete screen (part 2) NOTE: For P1600 series models, the option to download the PCL5e driver appears on this screen. 16. Click the Finish button. 17. The HP LaserJet Help Navigation application opens.
c. Click OK.
3. Click Install to begin the installation process. The Choose Easy Install or Advanced Install screen appears. Figure 3-108 Choose Easy Install or Advanced Install screen The Choose Easy Install or Advanced Install screen contains links to the following information. 4. ● The software End User License Agreement – use this link to view the end user license agreement. ● The HP recommended software package – use this link to view information about the HP Customer Participation Program.
5. Select an appropriate printer model on the Select Printer screen and click the Next button.
6. Select Configure to Print over the Wireless Network if you are installing a new wireless printer and are not installing the driver for the purpose of connecting to a printer that already exists on your wireless network. Click the Next button.
7. On the Wireless Discovery Method dialog, select Automatic (Recommended) to allow the installer to automatically locate your wireless router or access point. Click the Next button. Figure 3-111 Wireless Discovery Method screen NOTE: Selecting Advanced on the Wireless Discovery Method dialog allows you to manually enter your wireless network credentials.
8. Select the Network Name (SSID) to connect to on the Networks Discovered dialog. Click the Next button.
9. When the installer and the product connect via the wireless network, the Network Connection Successful screen appears. Disconnect the USB cable between the computer and the product and click the Next button.
10. The Congratulations! Software installation complete screen appears upon successful installation of the driver. Figure 3-114 Software installation complete screen (part 1) 11. Select Register your product and Print Test Page, and then click the Next button. A Web browser opens to the HP Product Registration page, and a test page prints at the product.
12. The Congratulations! Software installation complete screen appears with links to download HP Smart Web Printing and the XPS driver. Figure 3-115 Software installation complete screen (part 2) NOTE: For P1600 series models, the option to download the PCL5e driver appears on this screen. 13. Click the Finish button. 14. The HP LaserJet Help Navigation application opens.
c. Click OK.
3. Click Install to begin the installation process. The Choose Easy Install or Advanced Install screen appears. Figure 3-117 Choose Easy Install or Advanced Install screen The Choose Easy Install or Advanced Install screen contains links to the following information. 4. ENWW ● The software End User License Agreement – use this link to view the end user license agreement. ● The HP recommended software package – use this link to view information about the HP Customer Participation Program.
5. Select a appropriate printer model on the Select Printer screen and click the Next button.
6. Select Connect to a configured Wireless Network Printer. Click the Next button.
7. On the Identify Printer screen, choose to either select the printer to connect to from a list of detected printers (the recommended method) or specify a printer to connect to by manually entering an address for the printer. Click the Next button. Figure 3-120 Identify Printer screen If you choose to select Specify a printer by address, you will be required to identify the product by selecting and entering a value for one of the following printer identification methods.
Figure 3-121 Specify Printer screen Select a method to identify your product, enter a value for the selected identification method, and then click the Next button.
8. The Printer Found screen appears if the installer was able to locate your printer on the local wireless network. Figure 3-122 Printer Found screen Select Yes, install this printer and then click the Next button to install the printer found by the installer. Click No, I want to install a different printer and then click the Next button to return to the Identify Printer screen (Figure 3-120 Identify Printer screen on page 172) to search for a different printer.
9. The Confirm Network Settings screen appears Figure 3-123 Confirm Network Settings screen Click the Next button to confirm the network settings and continue the installation, or click the Change Settings button to edit the network settings.
10. The Congratulations! Software installation complete screen appears upon successful installation of the driver. Figure 3-124 Software installation complete screen (part 1) 11. Select Register your product and Print Test Page, and then click the Next button. A Web browser opens to the HP Product Registration page, and a test page prints at the product.
12. The Congratulations! Software installation complete screen appears with links to download HP Smart Web Printing and the XPS driver. Figure 3-125 Software installation complete screen (part 2) NOTE: For P1600 series models, the option to download the PCL5e driver appears on this screen. 13. Click the Finish button. 14. The HP LaserJet Help Navigation application opens.
Disable HP Smart Install for the product using the following steps. a. Navigate to the folder that contains the extracted XPS files and start the HP Smart Install Utility by double clicking SIUtility.exe (or SIUtiltiy64.exe for 64 bit operating systems) in the UTIL folder. b. On the Welcome to the HP Smart Install Utility click the Printer button.
c. Select the printer from the list and then click the Next button. Figure 3-127 HP Smart Install Printer Configuration screen d. On the This Printer's HP Smart Install is currently Enabled dialog click the Disable HP Smart Install on the selected Printer button. Figure 3-128 HP Smart Install currently Enabled screen e. ENWW On the message box that appears, click Yes to confirm the disabling ofHP Smart Install.
f. Click the Close button on the This Printer's HP Smart Install is currently Disabled screen. Figure 3-129 HP Smart Install currently Disabled screen g. Click the Close button on the Choose the printer to configure HP Smart Install screen. h. Click the Close button on the Welcome to the HP Smart Install Utility screen. i. Unplug the USB cable from the printer and then plug it back in.
4. On the Welcome to the Found New Hardware Wizard screen, select No beneath Can Windows connect to Windows Update to search for software?.
5. On the next Found New Hardware Wizard screen, select Install from a specific location (Advanced) and then click the Next button. 6. Select Don't search, I will choose the driver to install. and then click the Next button.
7. ENWW Ensure that Show compatible hardware is selected. Select your printer in the Printers list, and then click the Have Disk... button.
8. Navigate to the location of the XPS .inf file, select the XPS .inf file (example: HP1100XPS.INF), and then click the Open button. Figure 3-131 Locate File dialog window 9. Click the OK button on the Install From Disk dialog 10. Click the Next button. The driver installation proceeds automatically.
11. Click the Finish button to complete the installation and to close the Add New Hardware Wizard. NOTE: The Found New Hardware Wizard will run twice for a new driver installation; once for the XPS HP LaserJet Professional Printer driver and once for the USB EWS Device Driver. Existing driver install Use the following procedure to install the XPS driver when an instance of the HP LaserJet Professional P1100/P1560/P1600 Series Printer driver is installed. 1. Extract the XPS zip file to a folder location.
3. Right click in the Printers and Faxes window and select Add Printer. The Add Printer Wizard screen opens.
4. On the Local or Network Printer screen, select Local printer attached to this computer, and then click the Next button.
5. On the Select a Printer Port screen, select Use the following port: and then select the port your HP LaserJet Professional P1100/P1560/P1600 Series Printer uses. Click the Next button.
6. On the Install Printer Software screen, select your printer in the Printers list, and then click the Have Disk... button.
7. Navigate to the location of the XPS .inf file, select the XPS .inf file (example: HP1100XPS.INF), and then click the Open button. Figure 3-136 8. Click the OK button on the Install From Disk dialog and then click the Next button.
9. On the Use Existing Driver screen, select Keep existing driver (recommended) and then click the Next button.
10. On the Name Your Printer screen, enter or a name for the printer or use the existing name. Select whether to use this printer as your default printer. Click the Next button. Figure 3-138 Name Your Printer screen 11. On the Printer Sharing screen, select whether to share this printer. Click the Next button. 12. On the Print Test Page screen, select whether to print a test page. Select the Next button.
13. Click the Finish button on the Completing the Add Printer Wizard screen to complete the installation.
Additional installation information CD Re-launch Pad After a HP LaserJet Professional P1100/P1560/P1600 Series Printer series printer driver is installed, running setup.exe from the product CD starts the CD-Relaunch Pad. Figure 3-140 CD Re-launch Pad screen Use the CD Re-launch Pad for the following. ● Add another printer: Add another printer to your computer. ● Repair: Repair the products's software on your computer.
Task/issue P1102 (wireless) P1606dn (auto-duplexing, network) Install the same printer on a USB port and on a network Recommended method Recommended method 1. Install the product on a wireless network. 1. Install the product on a wireless network. 2. After the wireless install is complete, connect the product to the computer with a USB cable. 2. After the wireless install is complete, connect the product to the computer with a USB cable. 3.
● Cancel. Click this button to exit the installer without installing the product. When you click Cancel, a dialog box opens, allowing you to confirm cancellation of the installation by clicking Yes, or to return to the installation by clicking No. Figure 3-141 Installation Cancellation dialog box Click Finish to close the installer. Set a default printer 1. In Windows 7, click the Start button, click Control Panel, and then click Devices and Printers. 2.
Uninstall software ● Uninstall the Host-based driver ● Uninstall the XPS driver Uninstall the Host-based driver ● Use the HP Uninstall utility (recommended) ● Use Windows Add or Remove Programs feature Use the HP Uninstall utility (recommended) 1. Click the Start button, select All Programs, select HP, select your product name, and then click the Uninstall utility. 2. The Printer Uninstall List screen appears.
2. Click the entry for the HP LaserJet Professional P1100/P1560/P1600 Series Printer product, and then click Remove. The following screen appears. Figure 3-142 Uninstall Select the product, or products, to uninstall and then click Remove One or Remove All to initiate the uninstall process. Uninstall the XPS driver 1. In Windows 7, click the Start button, click Control Panel, and then click Devices and Printers. 2.
4 HP Host-based print driver for Windows Introduction This chapter describes the features of the HP LaserJet Professional P1100/P1560/P1600 Series Printer Host-based Print Driver for Windows XP (32-bit and 64-bit), Windows Server 2003 (32-bit and 64-bit), Windows Vista (32-bit and 64-bit), Windows Server 2008 (32-bit and 64-bit), and Windows 7 (32-bit and 64-bit).
Gain access to print drivers Depending on the operating system on which you are installing the print drivers, you can gain access to the print drivers and different print-driver interfaces in several ways. To gain access to the print-driver settings from within most software programs, follow these steps: 1. Click File. 2. Click Print. 3. Click Properties. The appearance and names of the driver tabs can vary, depending on the operating system.
Properties driver tabs This set of tabs controls the driver behavior and driver connections. To gain access to the Properties tabs, follow these steps: 1. Windows Vista: Click Start, click Control Panel, click Hardware and Sound, and then click Printers. Windows XP and Windows Server 2003: Click Start, click Settings, and then click Printers and Faxes. Windows Server 2008: Click Start, click Control Panel, and then open the Printers folder.
Help system The HP Host-based print driver includes a full-featured Help system to provide assistance with printing and configuration options. “What's this?” Help Windows XP, Windows Server 2003, Windows Server 2008, Windows Vista, and Windows 7 support What's this? Help. You can gain access to What's this? Help messages in any of the following ways: ● Right-click a feature or control. A pop-up Help window appears.
Advanced tab features NOTE: The Advanced tab is in the Printing Preferences tab set. For information about how to gain access to these tabs, see Printing Preferences driver tabs on page 200. Use the Advanced tab to change the layout of printed pages.
Follow these steps to create a Print Task Quick Set. ● Open the printer driver, and then click the Properties or Preferences button. ● Select the print options for the new quick set. ● Type a name for the quick set, and then click Save. Follow these steps to use a Print Tasks Quick Set. ● Open the printer driver, and then click the Properties or Preferences button.
● Effects ● Finishing Switching between tabs does not change the location or appearance of the document preview image. When you move the mouse over the document preview image, the mouse cursor changes from an arrow to a gloved hand. You can toggle between portrait and landscape page orientation by clicking the image.
Paper/Quality tab features NOTE: The Paper/Quality tab is in the Printing Preferences tab set. For information about how to gain access to these tabs, see Printing Preferences driver tabs on page 200. Use the Paper/Quality tab to specify paper size, type, and source. You can also use this tab to specify different paper selections for the front cover, first page, other pages, last page, and back cover of the document. The following figure shows the Paper/Quality tab.
Follow these steps to create a Print Task Quick Set. ● Open the printer driver, and then click the Properties or Preferences button. ● Select the print options for the new quick set. ● Type a name for the quick set, and then click Save. Follow these steps to use a Print Tasks Quick Set. ● Open the printer driver, and then click the Properties or Preferences button.
NOTE: Certain software programs can override the size command and specify different paper sizes within a single document. For information about paper sizes, see Engineering Details on page 247. NOTE: Several paper sizes are listed in the paper size drop-down menu that are physically too large for the product, such as 16k. These sizes are included for scaling purposes– the product scales down the printed output from a larger original size used by a software program.
Size The Width: and Length: values can be changed by typing numeric strings into the edit boxes. Any entry that is too large is rounded down to the maximum valid entry, while any entry that is too small is rounded up to the minimum valid entry. If units are in millimeters, the custom paper-size range minimum is the limit rounded up to the nearest whole millimeter. The custom paper-size range maximum is the limit rounded down to the nearest whole millimeter.
The following page or cover selections, and their paper source and type or cover type, are available. ● Front Cover: Add a Blank or Preprinted Cover ● First Page: Source is:, Type is:, and Show important instructions for printing on short media. ● Other Pages: Source is:, Type is:, and Show important instructions for printing on short media. ● Last Page: Source is:, Type is:, and Show important instructions for printing on short media.
paper from the main input tray. For information about paper sources, see Engineering Details on page 247. If Manual Feed is selected, the product will display a status message to load paper. Type Is The Type Is: drop-down menu contains the paper types the product is capable of processing.
● Effects ● Finishing Switching between tabs does not change the location or appearance of the document preview image. When you move the mouse over the document preview image, the mouse cursor changes from an arrow to a gloved hand. You can toggle between portrait and landscape page orientation by clicking the image.
Effects tab features NOTE: The Effects tab is in the Printing Preferences tab set. For information about how to gain access to these tabs, see Printing Preferences driver tabs on page 200. Use the Effects tab to create unique paper effects such as scaling and watermarks. The following figure shows the Effects tab.
Follow these steps to create a Print Task Quick Set. ● Open the printer driver, and then click the Properties or Preferences button. ● Select the print options for the new quick set. ● Type a name for the quick set, and then click Save. Follow these steps to use a Print Tasks Quick Set. ● Open the printer driver, and then click the Properties or Preferences button.
image is clipped. If it is smaller, then it is centered within the target paper. The following figure shows the effect that Scale To Fit has on a document formatted for Legal-size paper but printed on Letter.
● Effects ● Finishing Switching between tabs does not change the location or appearance of the document preview image. When you move the mouse over the document preview image, the mouse cursor changes from an arrow to a gloved hand. You can toggle between portrait and landscape page orientation by clicking the image. Watermarks Use the Watermarks feature to select a watermark, create a new watermark (text only), or edit an existing watermark.
Watermark Details Click Edit, and the Watermark Details dialog box appears. Figure 4-8 Watermark Details dialog box The dialog box shows a preview image and provides options for creating a new watermark and controlling the message angle and font attributes. Click OK to accept all of the changes that are made in the Watermark Details dialog box. However, clicking Cancel does not cancel all of the changes.
Watermark Message The Watermark Message is also the name that identifies the watermark in the Current Watermarks list, except when more than one watermark has the same message. For example, you can have several different watermarks with the message DRAFT, each with a different typeface or font size. When this occurs, the string is appended with a space, a pound sign, and a number (for example, Draft #2).
◦ Very dark ◦ Darkest These values represent the intensity of the gray that is used. Light produces a lightly saturated gray watermark, Lightest produces the lightest shade of watermark, and Darkest produces a black watermark. ● Size Font sizes from 1 to 999 points are available from the Size menu. The default point size is language dependent.
Finishing tab features NOTE: The Finishing tab is on the Printing Preferences tab set. For information about how to gain access to these tabs, see Printing Preferences driver tabs on page 200. Use the Finishing tab to print booklets and control the paper output. The following figure shows the Finishing tab.
Follow these steps to create a Print Task Quick Set. ● Open the printer driver, and then click the Properties or Preferences button. ● Select the print options for the new quick set. ● Type a name for the quick set, and then click Save. Follow these steps to use a Print Tasks Quick Set. ● Open the printer driver, and then click the Properties or Preferences button.
◦ Envelope B5 ◦ Envelope C5 ◦ Envelope C6 ◦ Envelope DL ◦ Statement ◦ 4x6 ◦ 5x8 ◦ A6 ◦ B6 NOTE: The check box for Print on both sides (manually) is not disabled if paper types or sizes that are not allowed for duplexing are selected. However, on the Paper/Quality tab next to the paper type or size setting, a caution symbol shows if a selection is not supported by the printer.
To print a multiple-page document on a product that supports manual duplex only, follow these steps. 1. Select the Print on Both Sides (Manually) check box. 2. Click OK. The even-number pages of the document print. 3. When the Print on Both Sides Instructions dialog appears, insert the stack of paper (on which the even-number pages have been printed) and then press the Continue button, as indicated in the following figure.
Figure 4-11 Print on Both Sides Instructions dialog box When you have completed the steps that appear in the dialog box, the second half of the print job prints on the back side of the stack of paper. The driver does not require the program to specifically support odd- and even-page printing, because the driver coordinates this function. Print on both side automatically (P1600 series products) For paper types that are supported for automatic duplexing, follow these steps to print a multiple-page document.
NOTE: Transparency, Labels, Envelope, and Vellum paper types cannot be duplexed with P1600 series products, either automatically or manually. Selecting any of these paper types makes the Print on both sides option unavailable on the Finishing tab. Flip pages up Use the Flip pages up check box to specify the duplex-binding option. By default, the Flip pages up check box is not available. It is available only when Print on both sides is selected.
Pages per sheet Use the Pages per sheet: option to select the number of pages that you want to print on a single sheet of paper. If you choose to print more than one page per sheet, the pages appear smaller and are arranged on the sheet in the order that they would otherwise be printed.
● 9 pages per sheet ● 16 pages per sheet Document preview image The document preview image is a line-drawn image of a page that represents graphics and text. The document preview image is always oriented so that the contents of the page are right-side-up.
Services tab features NOTE: The Services tab is on the Printing Preferences tab set. For information about how to gain access to these tabs, see Printing Preferences driver tabs on page 200. The Services tab is shown in the following figure.
If you have Internet access, select any of these items and then click Go! to open the corresponding HP Web page. Print Information Pages Use the Print Information Pages section of the Services tab to print the following information pages.
Device Settings Gain access to the product's Device Settings by following these steps. 1. Windows Vista and Windows 7: Click Start, click Control Panel, and then in the category for Hardware and Sound click Printer. -orWindows XP, Windows Server 2003, and Windows Server 2008 (using the default Start menu view): Click Start, and then click Printers and Faxes. -orWindows XP, Windows Server 2003, and Windows Server 2008 (using the Classic Start menu view): Click Start, click Settings, and then click Printers.
Figure 4-15 Device Settings tab - P1606dn model shown The following settings can be configured on the Device Settings tab. ● Jam Recovery ● Status Messages ● Cleaning Page ● Quiet Mode (P1560/P1600 series only) ● Duplex Mode ● Print Density ● Auto-Off Console NOTE: Click the Apply button on the Device Settings tab to apply any changed settings.
Jam Recovery When the Jam Recovery feature is turned on, the product reprints any pages that are damaged during a jam. The default setting for Jam Recovery is Off. Status Messages When the Status Messages feature is turned on, status messages related to the operation of the product appear. The default, and recommended, setting for Status Messages is On. For example, if the front door of the product is open when a print job is sent to the product, the following message appears.
Cleaning Page Use the Cleaning Page feature to remove excess toner and paper particles that accumulate on the fuser assembly and rollers. Follow these steps to print a Cleaning Page. 1. On the Device Settings tab, press the Start button in the Cleaning Page section. The HP LaserJet Cleaning Utility starts. 2. Make sure the product is idle and the Ready LED on the product is on. 3. Load overhead transparency or copier grade paper (18lb - 24lb or 70g/m2 - 90g/m2) with a smooth surface. 4.
234 Chapter 4 HP Host-based print driver for Windows ENWW
5 Macintosh software and utilities Introduction The HP LaserJet Professional P1100/P1560/P1600 Series Printer comes with software and installers for Apple, Inc. Macintosh systems. This chapter provides procedures for installing and removing the HP LaserJet Professional P1100/ P1560/P1600 Series Printer printing-system software for Macintosh operating systems, as well as descriptions about the software and utilities.
Supported operating systems for Macintosh The product supports the following Mac operating systems: ● Mac OS X 10.4, 10.5, 10.6, and later NOTE: For Mac OS X 10.4 and later, PPC and Intel® Core™ Processor Macs are supported.
PDEs Printer Dialog Extensions (PDEs) are code plug-ins that provide access to product features, such as number of copies, duplexing, and quality settings. The PDEs are HP additions to Apple's print driver. HP Embedded Web Server Mac OS X v10.4 and later support the HP Embedded Web Server (HP EWS) on wireless and network capable models. Use the HP LaserJet Utility to control features that are not available in the driver.
Macintosh installation instructions On a Macintosh computer, the installation procedures are basically the same for a network administrator, a network client, and a single user. Install the software on any computer that has save rights to the product. Users must have Administrator rights to install the software.
Mac OS X installation This section provides information about the various installation dialog-box sequences for the Mac OS X operating system. Main Install dialog box sequence NOTE: Turn on the power to the product and connect the USB cable between the product and the computer before inserting the HP LaserJet Professional P1100/P1560/P1600 Series Printer printingsystem software CD in the CD-ROM drive. 1.
3. In the HP LaserJet installer browser screen, double-click the HP LaserJet Professional P1100/ P1560/P1600 Series Printer icon to open the installer program Introduction dialog. Figure 5-2 Mac installer Introduction dialog 4. Click the Continue button. The License dialog appears.
5. You can save or print the license file by clicking the Save button or the Print button. 6. Read the software license agreement, and then click the Continue file. The license agreement dialog appears. Figure 5-4 Mac installer license agreement dialog 7. Click the Disagree button to end the installation and close the installer, or click the Agree button to continue the installation. The Select a Destination dialog appears.
8. Click the name of the volume to install the software and then click the Continue button. The Standard install on “Macintosh HD” dialog appears. 9. Click the Install button to start the installation. To change the installation location, click the Change Install Location... button to return to the Select a Destination dialog.
10. The Installation dialog appears. A progress bar shows the percentage of the installation progress that has been completed. Allow the program to install the software. Figure 5-6 Mac installer Installation dialog 11. As the installation nears completion, the HP LaserJet Firmware Download Utility dialog appears. Select USB Printers for products that will be used with USB connections. Select Network Printers for nettwork connected products. Click the OK button.
12. When the installation is complete, the Installation completed successfully dialog appears, stating that the installation was successful. Figure 5-7 Mac installer Summary dialog Click the Close button to exit the installer. NOTE: Complete the instructions for Mac OS X v10.4 in Setup instructions on page 244 to set up a printer queue for your HP LaserJet Professional P1100/P1560/P1600 Series Printer product.
Troubleshooting the product setup ● USB connected products ● Wireless products USB connected products If the product does not appear in the printer list after an installation: Complete each one of these solutions in the order given, and restart the setup process after each one to see if the issue has been resolved. ● Verify that the USB is connected between the product and the computer and that the product is powered on. ● Try disconnecting and reconnecting the cable.
246 Chapter 5 Macintosh software and utilities ENWW
6 Engineering Details Introduction This chapter presents engineering detail for the following topics: ENWW ● Remote firmware update ● Media attributes ● Supported routers for wireless products that support automatic configuration.
Remote firmware update The HP LaserJet Professional P1100/P1560/P1600 Series Printer products may require periodic updates to their firmware. The process for updating firmware involves three steps: 1. Determine the current level of firmware that is installed on the product. 2. Obtain the firmware update utilty from the HP Web site. 3. Run the firmware update utility to update the new firmware on the product.
Run the firmware update utility 1. Start the firmware update utility. Select the product or products to update the firmware from the list of available printers, and then click the Update One or Update All button. Figure 6-1 Firmware Update Utility. List of available printers shown screen. 2. Click Yes to confirm the firmware update on the dialog screen that appears. 3. The following dialog screen appears upon successful updating of the firmware. Figure 6-2 Firmware update successful screen.
Media attributes This section includes the following information about paper attributes: ● Paper sources and destinations ● Paper-source commands ● Driver-supported paper sizes ● Driver-supported paper types ● Custom paper sizes ● Paper-type commands (HP LaserJet Professional P1600 Series Printer only) Paper sources and destinations The following table indicates the standard and optional paper sources and destinations for the HP LaserJet Professional P1100/P1560/P1600 Series Printer product.
Table 6-3 Supported paper and print media sizes Size Dimensions Letter 216 x 279 mm (8.5 x 11 in) Legal 216 x 356 mm (8.5 x 14 in) A4 210 x 297 mm (8.27 x 11.69 in) Executive 184 x 267 mm (7.25 x 10.5 in) 8.5 x 13 216 x 330 mm (8.5 x 13 in) A5 148 x 210 mm (5.83 x 8.27 in) A6 105 x 148 mm (4.13 x 5.83 in) 16k 195 x 270 mm (7.68 x 10.62 in) Input tray Document feeder Minimum: 76 x 127 mm (3 x 5 in) Minimum: 147 x 211 mm (5.8 x 8.3 in) 184 x 260 mm (7.24 x 10.23 in) 195 x 270 mm (7.
Driver-supported paper types The following table shows the paper types that the HP LaserJet Professional P1100/P1560/P1600 Series Printer print-drivers support.
Custom paper sizes The following table shows custom paper sizes that are available for the HP LaserJet Professional P1100/ P1560/P1600 Series Printer product. Table 6-5 HP PCL 5 print driver custom paper sizes Tray Dimensions Minimum Maximum Tray 1 (150-sheet multipurpose) Width 98.4 mm (3.9 in) 216 mm (8.5 in) Length 148 mm (5.8 in) 356 mm (14.
Supported routers for wireless products that support automatic configuration. NOTE: Other wireless routers that do not support automatic configuration or provide a secure wireless environment maybe supported for this product but are not listed here. Wireless versions of this product support the following routers.
● ● Netgear ◦ Netgear DG834G ◦ Netgear FVG318NA ◦ Netgear WFS709TP ◦ Netgear WG102 ◦ Netgear WG302 ◦ Netgear WG602 ◦ Netgear WGL102 ◦ Netgear WGR614 ◦ Netgear WGT624 ◦ Netgear WGX102 ◦ Netgear WGXB102 ◦ Netgear WN802T ◦ Netgear WNDR3300 ◦ Netgear WNHDE111 ◦ Netgear WNR3500 ◦ Netgear WNR834B ◦ Netgear WNR854T ◦ Netgear WPN802 ◦ Netgear WN802T ◦ Netgear WPN824 Huawei ◦ ● Adtran ◦ ● ENWW Huawei WBR204g Adtran NetVanta 150 Belkin ◦ Belkin F5D7132 ◦ Belkin F5D7
● ● ◦ Belkin N1 Vision ◦ Belkin N1 Wireless ◦ Belkin Wireless G ◦ Belkin Wireless Pre-N Linksys ◦ Linksys WAP54G ◦ LINKSYS WAP200 ◦ LINKSYS WAP4400N ◦ Linksys WCG200 ◦ Linksys WRE54G ◦ Linksys WRT54G ◦ Linksys WRTP54G ◦ Linksys WRT54G2 ◦ Linksys WRT54GL ◦ Linksys WRT54GS ◦ Linksys WRT55AG ◦ Linksys WRT100 ◦ Linksys WRT110 ◦ Linksys WRT150N ◦ Linksys WRT160N ◦ Linksys WRT300N ◦ Linksys WRT310N ◦ Linksys WRT330N ◦ Linksys WRT350N ◦ Linksys WRT55AG ◦ Linksys W
● ● ● ● ● ENWW ◦ TRENDnet TEW-450APB ◦ TRENDnet TEW-453APB ◦ TRENDnet TEW-631BRP ◦ TRENDnet TEW-633GR ◦ TRENDnet TEW-611BRP ◦ TRENDnet TPL-210AP SMC Networks ◦ SMC SMC2555W-AG2 ◦ SMC SMC2552W-G2 ◦ SMC SMC2890W-AG ◦ SMC SMCWGBR14-N ◦ SMC SMCWBR14S-N2 ◦ SMC SMCWBR14T-G ◦ SMC SMCWEB-N Motorola ◦ Motorola SBG900 ◦ Motorola SBG1000 ◦ Motorola WR850G Dell ◦ Dell 2300 ◦ Dell 2350 ◦ Dell 4350 Asus ◦ Asus WL-330GE ◦ Asus WL-500g ◦ Asus WL-500W ◦ Asus WL-520g Kyocer
258 Chapter 6 Engineering Details ENWW
Index A accessibility, documentation 34 Acrobat Reader viewing documentation 23 ADA (Americans with Disabilities Act) compliance 34 Add Printer installation 49 Add Printer Wizard, detailed install existing port for a direct connection, using 51 print server connection 50 TCP/IP port for direction connection, creating 51 Adobe Acrobat Reader viewing documentation 23 Americans with Disabilities Act (ADA) compliance 34 autorun CD-ROM, Windows 42, 48 install Windows printing-system software from 48 languages,
H heavy paper, paper type commands 253 Help print drivers 202 help Macintosh 237 Help button, Windows installation dialog boxes 195 HP Embedded Web Server Macintosh support 237 HP EWS (wireless models only) about 44 HP Host-based Print Driver features 199 settings 199 HP LaserJet Utility, Macintosh about 17 Configuration Settings list 17 open 17 HP PCL 5 Universal Print Driver about 15 See also printer drivers HP PostScript Universal Print Driver about 15 See also printer drivers HP Smart Install 109, 115,
Printer Dialog Extensions (PDEs) 237 printer drivers Advanced tab content 203 Advanced tab contents 203 Booklet Printing settings, Finishing tab 225 Copies settings, Advanced tab 204 Document Options settings, Finishing tab 221 document preview image 204, 211, 215, 227 Effects tab content 213 Finishing tab contents 220 Flip Pages Up setting, Finishing tab 225 gain access to settings 200 Help system 202 incompatible print settings messages 202 Internet Services options, Services tab 228 Orientation settings,
See also HP PCL 5 Universal Print Driver; HP PostScript Universal Print Driver updating firmware remotely.
© 2010 Hewlett-Packard Development Company, L.P. www.hp.