HP MPX200 Mutifunction Router Command Line Interface User Guide (5697-2512, May 2013)
FCIP SW Compression(0=Enable,1=Disable,2=Auto)[Auto ]
All attribute values for FCIP Route 1 will now be saved.
The following is an example of the fciproute add command used to add a 10 Gb FCIP route.
At the GE Port prompt, you must select a 10 Gb Ethernet port. Set the Window Scaling Factor to
3 for the default window size. Set the Bandwidth, Mbit/sec in a range from 1Mbps to 10000
Mbps.
MPX200 <1> (admin) #> fciproute add
A list of attributes with formatting and current values will follow. Enter a
new value or simply press the ENTER key to accept the current value. If you
wish to terminate this process before reaching the end of the list press 'q'
or 'Q' and the ENTER key to do so.
WARNING:
The following command might cause a loss of connections to both GE ports.
Configuring FCIP Route:
-----------------------
FCIP Interfaces FC & GE (0=Enable, 1=Disable) [Enabled ]
FC Port (1=FC1 2=FC2) [ ] 1
GE Port (1=GE1 2=GE2 3=10GE1 4=10GE2) [ ] 3
IP Address (IPv4 or IPv6; 0=IPv6 Link Local) [0.0.0.0 ] 172.35.15.11
Subnet Mask [0.0.0.0 ] 255.255.254.0
Gateway IP Address [0.0.0.0 ] 172.35.14.1
Remote IP Address [0.0.0.0 ] 172.17.136.18
MTU Size (0=Normal, 1=Jumbo, 2=Other) [Normal ]
TCP Window Size (0=32KB, 1=64KB, 2=128KB,
3=256KB, 4=512KB, 5=1MB, 6=2MB,
7=4MB, 8=8MB, 9=16MB) [32768 ]
Window Scaling (0=Enable, 1=Disable) [Enabled ]
Window Scaling Factor (Min=0, Max=9) [3 ]
TCP Port No. (Min=1024, Max=65535) [3225 ]
Bandwidth, Mbit/sec (Min=1, Max=10000) [10000 ]
VLAN (0=Enable, 1=Disable) [Disabled]
FCIP SW Compression(0=Enable,1=Disable,2=Auto)[Disabled]
All attribute values for FCIP Route 1 will now be saved.
The following is an example of the fciproute mod command
MPX200 <1> (admin) #> fciproute mod
A list of attributes with formatting and current values will follow. Entera new value or simply press the ENTER
key to accept the current value. If you
wish to terminate this process before reaching the end of the list press 'q' or
'Q' and the ENTER key to do so.
WARNING:
The following command might cause a loss of connections to both GE ports.
Route FC Port ID GE Port ID
----- ---------- ----------
1 FC1 GE1
Please select a FCIP route from the list above ('q' to quit): 1
Configuring FCIP Route:
-----------------------
FCIP Interfaces FC & GE (0=Enable, 1=Disable) [Enabled ]
IP Address (IPv4 or IPv6; 0=IPv6 Link Local) [172.35.15.11 ]
172.35.15.120
Subnet Mask [255.255.254.0]
Gateway IP Address [172.35.14.1 ]
Remote IP Address [172.17.136.18]
MTU Size (0=Normal, 1=Jumbo, 2=Other) [Normal ]
TCP Window Size (0=32KB, 1=64KB, 2=128KB, 3=256KB,
4=512KB, 5=1MB, 6=2MB,
7=4MB, 8=8MB, 9=16MB) [32768 ]
Window Scaling (0=Enable, 1=Disable) [Enabled ]
Window Scaling Factor (Min=0, Max=9) [7 ]
TCP Port No. (Min=1024, Max=65535) [3225 ]
GE Port Speed (0=Auto, 1=100Mb, 2=1Gb) [Auto ]
Bandwidth, Mbit/sec (Min=1, Max=1000) [1000 ]
VLAN (0=Enable, 1=Disable) [Disabled ]
FCIP SW Compression(0=Enable,1=Disable,2=Auto) [Auto ]
Do you want to save/discard changes? (0=Save, 1=Discard) [Save ]
All attribute values for FCIP Route 1 will now be saved.
16 Command reference