R2511-HP MSR Router Series Interface Command Reference(V5)
Table Of Contents
- Title Page
- Contents
- Ethernet interface configuration commands
- bandwidth
- combo enable
- default
- description
- display interface
- duplex
- flow-control
- flow-interval
- interface
- link-delay
- loopback
- port link-mode
- port link-mode interface-list
- reset counters interface
- shutdown
- speed
- broadcast-suppression
- display loopback-detection
- display counters
- display counters rate
- display port-group manual
- flow-interval
- group-member
- jumboframe enable
- loopback-detection control enable
- loopback-detection interval-time
- loopback-detection per-vlan enable
- mdi
- multicast-suppression
- port-group manual
- unicast-suppression
- virtual-cable-test
- mac-address
- mac-address valid-check
- mtu
- promiscuous
- qmtoken
- WAN interface configuration commands
- bandwidth
- default
- description
- link-delay
- shutdown
- async mode
- baudrate
- clock
- code
- country-code
- crc
- detect
- display interface analogmodem
- display interface aux
- display interface serial
- eliminate-pulse
- idle-mark
- invert receive-clock
- invert transmit-clock
- itf
- loopback
- looptest
- mtu
- physical-mode
- phy-mru
- reset counters interface
- reset counters interface
- reset counters interface
- reverse-rts
- timer hold
- virtualbaudrate
- autodeploy sms enable
- display cellular
- display cellular-ethernet
- display gps
- display interface cellular
- display interface cellular-ethernet
- display sms
- display sms statistics
- dm-port open
- gps mode
- gps nmea
- ip address cellular-allocated
- lte band
- mode cdma
- mode wcdma
- modem auto-recovery enable
- modem reboot
- modem response
- pin modify
- pin unlock
- pin verification
- pin verify
- plmn search
- plmn select
- profile create
- profile main
- recovery track
- reset counters interface cellular
- reset counters interface cellular-ethernet
- rssi
- sms delete
- sms forward
- sms send
- sms sending-enable
- snmp-agent trap enable sms
- standby rssi
- trust-imsi
- alarm
- cable (CE1/PRI interface)
- channel-set (CE1/PRI interface)
- clock (CE1/PRI interface)
- clock-change auto
- code (CE1/PRI interface)
- controller e1
- crc
- data-coding (CE1/PRI interface)
- detect-ais
- display controller e1
- error-diffusion restraint config
- error-diffusion restraint enable
- error-diffusion restraint restart-channel
- frame-format (CE1/PRI interface)
- idlecode (CE1/PRI interface)
- itf (CE1/PRI interface)
- loopback (CE1/PRI interface)
- looptest (CE1/PRI interface)
- pri-set (CE1/PRI interface)
- reset counters controller e1
- using (CE1/PRI interface)
- alarm (CT1/PRI interface)
- alarm-threshold
- bert (CT1/PRI interface)
- cable (CT1/PRI interface)
- channel-set (CT1/PRI interface)
- clock (CT1/PRI interface)
- code (CT1/PRI interface)
- controller t1
- crc
- data-coding (CT1/PRI interface)
- display controller t1
- error-diffusion restraint config
- error-diffusion restraint enable
- error-diffusion restraint restart-channel
- fdl
- frame-format (CT1/PRI interface)
- idlecode (CT1/PRI interface)
- itf (CT1/PRI interface)
- loopback (CT1/PRI interface)
- looptest (CT1/PRI interface)
- pri-set (CT1/PRI interface)
- reset counters controller t1
- sendloopcode
- clock-change auto
- crc
- display fe1
- fe1 alarm
- fe1 cable
- fe1 clock
- fe1 code
- fe1 data-coding
- fe1 frame-format
- fe1 idlecode
- fe1 itf
- fe1 loopback
- fe1 timeslot-list
- fe1 unframed
- crc
- display ft1
- ft1 alarm
- ft1 alarm-threshold
- ft1 bert
- ft1 cable
- ft1 clock
- ft1 code
- ft1 data-coding
- ft1 fdl
- ft1 frame-format
- ft1 idlecode
- ft1 itf
- ft1 loopback
- ft1 sendloopcode
- ft1 timeslot-list
- bert (CE3 interface)
- clock (CE3 interface)
- controller e3
- crc
- display controller e3
- e1 bert
- e1 channel-set
- e1 set clock
- e1 set frame-format
- e1 set loopback
- e1 shutdown
- e1 unframed
- fe3
- loopback (CE3 interface)
- national-bit
- reset counters controller e3
- using (CE3 interface)
- alarm (CT3 interface)
- bert (CT3 interface)
- cable (CT3 interface)
- clock (CT3 interface)
- controller t3
- crc
- display controller t3
- feac
- frame-format (CT3 interface)
- ft3
- loopback (CT3 interface)
- mdl (CT3 interface)
- reset counters controller t3
- t1 alarm
- t1 bert
- t1 channel-set
- t1 sendloopcode
- t1 set clock
- t1 set fdl
- t1 set frame-format
- t1 set loopback
- t1 show
- t1 shutdown
- t1 unframed
- using (CT3 interface)
- display interface bri
- loopback (ISDN BRI interface)
- mtu (ISDN BRI interface)
- reset counters interface
- ATM and DSL interface configuration commands
- bandwidth
- default
- description
- display interface atm
- interface atm
- reset atm interface
- reset counters interface
- shutdown
- cable (ATM E1 interface)
- cable (ATM T1 interface)
- clock
- clock-change auto
- code
- differential-delay
- display interface ima-group
- frame-format
- frame-length
- ima ima-group
- ima-clock
- ima-standard
- ima-test
- interface ima-group
- loopback
- min-active-links
- scramble
- cable
- clock
- frame-format
- loopback
- scramble
- clock
- flag
- frame-format
- loopback
- scramble
- activate
- adsl standard
- adsl tx-attenuation
- bootrom update file
- display dsl configuration
- display dsl status
- display dsl version
- activate
- display dsl configuration
- display dsl status
- display dsl version
- shdsl annex
- shdsl capability
- shdsl line-probing
- shdsl mode
- shdsl pam
- shdsl pbo
- shdsl psd
- shdsl rate
- shdsl snr-margin
- shdsl wire
- interface efm
- POS interface configuration commands
- CPOS interface configuration commands
- bandwidth
- clock
- controller cpos
- default
- description
- display controller cpos
- display controller cpos e1
- display controller cpos t1
- e1 channel-set
- e1 set clock
- e1 set flag
- e1 set frame-format
- e1 set loopback
- e1 shutdown
- e1 unframed
- flag
- frame-format
- loopback
- multiplex mode
- reset counters controller cpos
- shutdown
- t1 channel-set
- t1 set clock
- t1 set flag
- t1 set frame-format
- t1 set loopback
- t1 shutdown
- t1 unframed
- Loopback and null interface configuration commands
- Support and other resources
- Index

170
Field Descri
p
tion
Time: 0 minute(s), Time past: 0 minute(s) Duration of the BERT test and time that has elapsed.
Bit Errors (since test started) Number of bit errors received since start of the BERT test.
Bits Received (since test started) Number of bits received since start of the BERT test.
Bit Errors (since latest sync) Number of bit errors received since last synchronization.
Bits Received (since latest sync) Number of bits received since last synchronization.
Historical Statistics: Historical statistics.
Last clearing of counters: Never Counter clearing records.
Data in current interval (285 seconds
elapsed):
0 Line Code Violations, 0 Path Code
Violations
0 Ais Alarm Secs, 286 Los Alarm Secs
7 Slip Secs, 286 Fr Loss Secs, 0 Line Err
Secs, 0 Degraded Mins
0 Errored Secs, 0 Bursty Err Secs, 0
Severely Err Secs, 286 Unavail Secs
Statistics spanning the current interval. The statistical items, such
as AIS alarm, LOS signal, and LFA, are provided according to the
T1 specifications for the physical layer.
For more information, see ANSI T1.403 and AT&T TR 54016.
Data in Interval 1:
0 Line Code Violations, 0 Path Code
Violations
0 Ais Alarm Secs, 901 Los Alarm Secs
22 Slip Secs, 901 Fr Loss Secs, 0 Line
Err Secs, 0 Degraded Mins
0 Errored Secs, 0 Bursty Err Secs, 0
Severely Err Secs, 901 Unavail Secs
Statistics spanning the first interval.
The statistical items are the same as those provided by the
statistics spanning the current interval.
Data in Interval 2:
0 Line Code Violations, 0 Path Code
Violations
0 Ais Alarm Secs, 900 Los Alarm Secs
23 Slip Secs, 900 Fr Loss Secs, 0 Line
Err Secs, 0 Degraded Mins
0 Errored Secs, 0 Bursty Err Secs, 0
Severely Err Secs, 900 Unavail Secs
Statistics spanning the second interval.
The statistical items are the same as those provided by the
statistics spanning the current interval.
Total Data (last 2 15 minute intervals):
0 Line Code Violations, 0 Path Code
Violations
0 Ais Alarm Secs, 2087 Los Alarm Secs
52 Slip Secs, 2087 Fr Loss Secs, 0 Line
Err Secs, 0 Degraded Mins
0 Errored Secs, 0 Bursty Err Secs, 0
Severely Err Secs, 2087 Unavail Secs
Statistics spanning the last two intervals.
The statistical items are the same as those provided by the
statistics spanning the current interval.










