R2511-HP MSR Router Series Interface Command Reference(V5)
Table Of Contents
- Title Page
- Contents
- Ethernet interface configuration commands
- bandwidth
- combo enable
- default
- description
- display interface
- duplex
- flow-control
- flow-interval
- interface
- link-delay
- loopback
- port link-mode
- port link-mode interface-list
- reset counters interface
- shutdown
- speed
- broadcast-suppression
- display loopback-detection
- display counters
- display counters rate
- display port-group manual
- flow-interval
- group-member
- jumboframe enable
- loopback-detection control enable
- loopback-detection interval-time
- loopback-detection per-vlan enable
- mdi
- multicast-suppression
- port-group manual
- unicast-suppression
- virtual-cable-test
- mac-address
- mac-address valid-check
- mtu
- promiscuous
- qmtoken
- WAN interface configuration commands
- bandwidth
- default
- description
- link-delay
- shutdown
- async mode
- baudrate
- clock
- code
- country-code
- crc
- detect
- display interface analogmodem
- display interface aux
- display interface serial
- eliminate-pulse
- idle-mark
- invert receive-clock
- invert transmit-clock
- itf
- loopback
- looptest
- mtu
- physical-mode
- phy-mru
- reset counters interface
- reset counters interface
- reset counters interface
- reverse-rts
- timer hold
- virtualbaudrate
- autodeploy sms enable
- display cellular
- display cellular-ethernet
- display gps
- display interface cellular
- display interface cellular-ethernet
- display sms
- display sms statistics
- dm-port open
- gps mode
- gps nmea
- ip address cellular-allocated
- lte band
- mode cdma
- mode wcdma
- modem auto-recovery enable
- modem reboot
- modem response
- pin modify
- pin unlock
- pin verification
- pin verify
- plmn search
- plmn select
- profile create
- profile main
- recovery track
- reset counters interface cellular
- reset counters interface cellular-ethernet
- rssi
- sms delete
- sms forward
- sms send
- sms sending-enable
- snmp-agent trap enable sms
- standby rssi
- trust-imsi
- alarm
- cable (CE1/PRI interface)
- channel-set (CE1/PRI interface)
- clock (CE1/PRI interface)
- clock-change auto
- code (CE1/PRI interface)
- controller e1
- crc
- data-coding (CE1/PRI interface)
- detect-ais
- display controller e1
- error-diffusion restraint config
- error-diffusion restraint enable
- error-diffusion restraint restart-channel
- frame-format (CE1/PRI interface)
- idlecode (CE1/PRI interface)
- itf (CE1/PRI interface)
- loopback (CE1/PRI interface)
- looptest (CE1/PRI interface)
- pri-set (CE1/PRI interface)
- reset counters controller e1
- using (CE1/PRI interface)
- alarm (CT1/PRI interface)
- alarm-threshold
- bert (CT1/PRI interface)
- cable (CT1/PRI interface)
- channel-set (CT1/PRI interface)
- clock (CT1/PRI interface)
- code (CT1/PRI interface)
- controller t1
- crc
- data-coding (CT1/PRI interface)
- display controller t1
- error-diffusion restraint config
- error-diffusion restraint enable
- error-diffusion restraint restart-channel
- fdl
- frame-format (CT1/PRI interface)
- idlecode (CT1/PRI interface)
- itf (CT1/PRI interface)
- loopback (CT1/PRI interface)
- looptest (CT1/PRI interface)
- pri-set (CT1/PRI interface)
- reset counters controller t1
- sendloopcode
- clock-change auto
- crc
- display fe1
- fe1 alarm
- fe1 cable
- fe1 clock
- fe1 code
- fe1 data-coding
- fe1 frame-format
- fe1 idlecode
- fe1 itf
- fe1 loopback
- fe1 timeslot-list
- fe1 unframed
- crc
- display ft1
- ft1 alarm
- ft1 alarm-threshold
- ft1 bert
- ft1 cable
- ft1 clock
- ft1 code
- ft1 data-coding
- ft1 fdl
- ft1 frame-format
- ft1 idlecode
- ft1 itf
- ft1 loopback
- ft1 sendloopcode
- ft1 timeslot-list
- bert (CE3 interface)
- clock (CE3 interface)
- controller e3
- crc
- display controller e3
- e1 bert
- e1 channel-set
- e1 set clock
- e1 set frame-format
- e1 set loopback
- e1 shutdown
- e1 unframed
- fe3
- loopback (CE3 interface)
- national-bit
- reset counters controller e3
- using (CE3 interface)
- alarm (CT3 interface)
- bert (CT3 interface)
- cable (CT3 interface)
- clock (CT3 interface)
- controller t3
- crc
- display controller t3
- feac
- frame-format (CT3 interface)
- ft3
- loopback (CT3 interface)
- mdl (CT3 interface)
- reset counters controller t3
- t1 alarm
- t1 bert
- t1 channel-set
- t1 sendloopcode
- t1 set clock
- t1 set fdl
- t1 set frame-format
- t1 set loopback
- t1 show
- t1 shutdown
- t1 unframed
- using (CT3 interface)
- display interface bri
- loopback (ISDN BRI interface)
- mtu (ISDN BRI interface)
- reset counters interface
- ATM and DSL interface configuration commands
- bandwidth
- default
- description
- display interface atm
- interface atm
- reset atm interface
- reset counters interface
- shutdown
- cable (ATM E1 interface)
- cable (ATM T1 interface)
- clock
- clock-change auto
- code
- differential-delay
- display interface ima-group
- frame-format
- frame-length
- ima ima-group
- ima-clock
- ima-standard
- ima-test
- interface ima-group
- loopback
- min-active-links
- scramble
- cable
- clock
- frame-format
- loopback
- scramble
- clock
- flag
- frame-format
- loopback
- scramble
- activate
- adsl standard
- adsl tx-attenuation
- bootrom update file
- display dsl configuration
- display dsl status
- display dsl version
- activate
- display dsl configuration
- display dsl status
- display dsl version
- shdsl annex
- shdsl capability
- shdsl line-probing
- shdsl mode
- shdsl pam
- shdsl pbo
- shdsl psd
- shdsl rate
- shdsl snr-margin
- shdsl wire
- interface efm
- POS interface configuration commands
- CPOS interface configuration commands
- bandwidth
- clock
- controller cpos
- default
- description
- display controller cpos
- display controller cpos e1
- display controller cpos t1
- e1 channel-set
- e1 set clock
- e1 set flag
- e1 set frame-format
- e1 set loopback
- e1 shutdown
- e1 unframed
- flag
- frame-format
- loopback
- multiplex mode
- reset counters controller cpos
- shutdown
- t1 channel-set
- t1 set clock
- t1 set flag
- t1 set frame-format
- t1 set loopback
- t1 shutdown
- t1 unframed
- Loopback and null interface configuration commands
- Support and other resources
- Index
323
exclude: Displays all lines that do not match the specified regular expression.
include: Displays all lines that match the specified regular expression.
regular-expression: Specifies a regular expression, a case-sensitive string of 1 to 256 characters.
Usage guidelines
If you do not specify the null keyword, this command displays information about all interfaces on the
device.
If you specify the null keyword, this command displays information about interface Null 0 with or without
the 0 keyword. This is because the device supports only one null interface.
Examples
# Display detailed information about null interface Null 0. (Suppose the null interface supports traffic
accounting.)
<Sysname> display interface null 0
NULL0 current state :UP
Line protocol current state :UP (spoofing)
Description : NULL0 Interface
The Maximum Transmit Unit is 1500
Internet protocol processing : disabled
Physical is NULL DEV
Last clearing of counters: Never
Last 300 seconds input: 0 bytes/sec, 0 bits/sec, 0 packets/sec
Last 300 seconds output: 0 bytes/sec, 0 bits/sec, 0 packets/sec
0 packets input, 0 bytes, 0 drops
0 packets output, 0 bytes, 0 drops
# Display detailed information about interface Null0. (Suppose the null interface does not support traffic
accounting.)
<Sysname> display interface null 0
NULL0 current state :UP
Line protocol current state :UP (spoofing)
Description : NULL0 Interface
The Maximum Transmit Unit is 1500
Internet protocol processing : disabled
Physical is NULL DEV
Last clearing of counters: Never
# Display brief information about interface Null 0.
<Sysname> display interface null 0 brief
The brief information of interface(s) under route mode:
Link: ADM - administratively down; Stby - standby
Protocol: (s) - spoofing
Interface Link Protocol Main IP Description
NULL0 UP UP(s) --
# Display complete interface description of Null 0.
<Sysname> display interface null 0 description
The brief information of interface(s) under route mode:
Link: ADM - administratively down; Stby - standby
Protocol: (s) - spoofing










