HP MSR2000/3000/4000 Router Series Layer 2 - LAN Switching Command Reference
Table Of Contents
- Title Page
- Contents
- MAC address table commands
- Port isolation commands
- Spanning tree commands
- active region-configuration
- check region-configuration
- display stp
- display stp abnormal-port
- display stp bpdu-statistics
- display stp down-port
- display stp history
- display stp region-configuration
- display stp root
- display stp tc
- instance
- region-name
- reset stp
- revision-level
- stp bpdu-protection
- stp bridge-diameter
- stp compliance
- stp config-digest-snooping
- stp cost
- stp edged-port
- stp enable
- stp global config-digest-snooping
- stp global enable
- stp global mcheck
- stp loop-protection
- stp max-hops
- stp mcheck
- stp mode
- stp no-agreement-check
- stp pathcost-standard
- stp point-to-point
- stp port priority
- stp port-log
- stp priority
- stp region-configuration
- stp role-restriction
- stp root primary
- stp root secondary
- stp root-protection
- stp tc-protection
- stp tc-protection threshold
- stp tc-restriction
- stp timer forward-delay
- stp timer hello
- stp timer max-age
- stp timer-factor
- stp transmit-limit
- vlan-mapping modulo
- Loop detection commands
- VLAN commands
- LLDP commands
- display lldp local-information
- display lldp neighbor-information
- display lldp statistics
- display lldp status
- display lldp tlv-config
- lldp admin-status
- lldp check-change-interval
- lldp enable
- lldp encapsulation snap
- lldp fast-count
- lldp global enable
- lldp hold-multiplier
- lldp management-address-format string
- lldp max-credit
- lldp mode
- lldp notification med-topology-change enable
- lldp notification remote-change enable
- lldp timer fast-interval
- lldp timer notification-interval
- lldp timer reinit-delay
- lldp timer tx-interval
- lldp tlv-enable
- Support and other resources
- Index
108
• Nearest customer bridge agents can advertise basic TLVs and IEEE 802.1 organizationally specific
TLVs.
On Layer 3 Ethernet interfaces:
• Nearest bridge agents can advertise all types of LLDP TLVs (only link aggregation TLV in 802.1
organizationally specific TLVs) except network policy TLVs.
• Nearest non-TPMR bridge agents advertise no TLVs.
• Nearest customer bridge agents can advertise basic TLVs and IEEE 802.1 organizationally specific
TLVs (only link aggregation TLV).
Views
Layer 2 Ethernet interface view, Layer 3 Ethernet interface view
Predefined user roles
network-admin
Parameters
agent: Specifies an LLDP agent type. If no agent type is specified in Ethernet interface view, the command
configures the types of advertisable TLVs for nearest bridge agents.
nearest-customer: Specifies nearest customer bridge agents.
nearest-nontpmr: Specifies nearest non-TPMR bridge agents.
all: Advertises all TLVs of a specific type.
• Enables the interface to advertise all basic LLDP TLVs, IEEE 802.1 organizationally specific LLDP TLVs,
or IEEE 802.3 organizationally specific LLDP TLVs if the all keyword is specified for basic-tlv, dot1-tlv,
or dot3-tlv.
• Enables the interface to advertise all LLDP-MED TLVs except location identification TLVs if the all
keyword is specified for med-tlv.
basic-tlv: Advertises basic LLDP TLVs.
management-address-tlv [ ip-address ]: Advertises management address TLVs. ip-address specifies the
management address to be advertised. By default:
• For a Layer 2 Ethernet interface, the management address is the main IP address of the VLAN
interface that is in up state and whose corresponding VLAN ID is the lowest among the VLANs
permitted on the port. If none of the VLAN interfaces of the permitted VLANs is assigned an IP
address or all VLAN interfaces are down, the MAC address of the port will be advertised.
• For a Layer 3 Ethernet interface, the management address is its own IP address. If no IP address is
configured for the Layer 3 Ethernet or aggregate interface, the MAC address of the port will be
advertised.
port-description: Advertises port description TLVs.
system-capability: Advertises system capabilities TLVs.
system-description: Advertises system description TLVs.
system-name: Advertises system name TLVs.
dot1-tlv: Advertises IEEE 802.1 organizationally specific LLDP TLVs.
port-vlan-id: Advertises port VLAN ID TLVs.