HP MSR2000/3000/4000 Router Series Layer 2 - LAN Switching Command Reference
Table Of Contents
- Title Page
- Contents
- MAC address table commands
- Port isolation commands
- Spanning tree commands
- active region-configuration
- check region-configuration
- display stp
- display stp abnormal-port
- display stp bpdu-statistics
- display stp down-port
- display stp history
- display stp region-configuration
- display stp root
- display stp tc
- instance
- region-name
- reset stp
- revision-level
- stp bpdu-protection
- stp bridge-diameter
- stp compliance
- stp config-digest-snooping
- stp cost
- stp edged-port
- stp enable
- stp global config-digest-snooping
- stp global enable
- stp global mcheck
- stp loop-protection
- stp max-hops
- stp mcheck
- stp mode
- stp no-agreement-check
- stp pathcost-standard
- stp point-to-point
- stp port priority
- stp port-log
- stp priority
- stp region-configuration
- stp role-restriction
- stp root primary
- stp root secondary
- stp root-protection
- stp tc-protection
- stp tc-protection threshold
- stp tc-restriction
- stp timer forward-delay
- stp timer hello
- stp timer max-age
- stp timer-factor
- stp transmit-limit
- vlan-mapping modulo
- Loop detection commands
- VLAN commands
- LLDP commands
- display lldp local-information
- display lldp neighbor-information
- display lldp statistics
- display lldp status
- display lldp tlv-config
- lldp admin-status
- lldp check-change-interval
- lldp enable
- lldp encapsulation snap
- lldp fast-count
- lldp global enable
- lldp hold-multiplier
- lldp management-address-format string
- lldp max-credit
- lldp mode
- lldp notification med-topology-change enable
- lldp notification remote-change enable
- lldp timer fast-interval
- lldp timer notification-interval
- lldp timer reinit-delay
- lldp timer tx-interval
- lldp tlv-enable
- Support and other resources
- Index
40
When the setting is configured in Layer 2 Ethernet interface view, it takes effect on only that interface.
Examples
# Enable No Agreement Check on Ethernet 2/1.
<Sysname> system-view
[Sysname] interface ethernet 2/1
[Sysname-Ethernet2/1] stp no-agreement-check
stp pathcost-standard
Use stp pathcost-standard to specify a standard for the device to use when calculating the default path
costs for ports.
Use undo stp pathcost-standard to restore the default.
Syntax
stp pathcost-standard { dot1d-1998 | dot1t | legacy }
undo stp pathcost-standard
Default
The device uses the legacy standard to calculate the default path costs for ports.
Views
System view
Predefined user roles
network-admin
Parameters
dot1d-1998: Configures the device to calculate the default path cost for ports based on IEEE
802.1d-1998.
dot1t: Configures the device to calculate the default path cost for ports based on IEEE 802.1t.
legacy: Configures the device to calculate the default path cost for ports based on a private standard.
Usage guidelines
If you change the standard that the device uses in calculating the default path costs, you restore the path
costs to the default.
Examples
# Configure the device to calculate the default path cost for ports based on IEEE 802.1d-1998.
<Sysname> system-view
[Sysname] stp pathcost-standard dot1d-1998
Related commands
• display stp
• stp cost
stp point-to-point
Use stp point-to-point to configure the link type of the ports.