HP MSR2000/3000/4000 Router Series Layer 2 - LAN Switching Command Reference
Table Of Contents
- Title Page
- Contents
- MAC address table commands
- Port isolation commands
- Spanning tree commands
- active region-configuration
- check region-configuration
- display stp
- display stp abnormal-port
- display stp bpdu-statistics
- display stp down-port
- display stp history
- display stp region-configuration
- display stp root
- display stp tc
- instance
- region-name
- reset stp
- revision-level
- stp bpdu-protection
- stp bridge-diameter
- stp compliance
- stp config-digest-snooping
- stp cost
- stp edged-port
- stp enable
- stp global config-digest-snooping
- stp global enable
- stp global mcheck
- stp loop-protection
- stp max-hops
- stp mcheck
- stp mode
- stp no-agreement-check
- stp pathcost-standard
- stp point-to-point
- stp port priority
- stp port-log
- stp priority
- stp region-configuration
- stp role-restriction
- stp root primary
- stp root secondary
- stp root-protection
- stp tc-protection
- stp tc-protection threshold
- stp tc-restriction
- stp timer forward-delay
- stp timer hello
- stp timer max-age
- stp timer-factor
- stp transmit-limit
- vlan-mapping modulo
- Loop detection commands
- VLAN commands
- LLDP commands
- display lldp local-information
- display lldp neighbor-information
- display lldp statistics
- display lldp status
- display lldp tlv-config
- lldp admin-status
- lldp check-change-interval
- lldp enable
- lldp encapsulation snap
- lldp fast-count
- lldp global enable
- lldp hold-multiplier
- lldp management-address-format string
- lldp max-credit
- lldp mode
- lldp notification med-topology-change enable
- lldp notification remote-change enable
- lldp timer fast-interval
- lldp timer notification-interval
- lldp timer reinit-delay
- lldp timer tx-interval
- lldp tlv-enable
- Support and other resources
- Index
45
Usage guidelines
When port role restriction is enabled on a port, the port cannot become a root port.
When the setting is configured in Layer 2 Ethernet interface view, it takes effect on only that interface.
Examples
# Enable port role restriction on interface Ethernet 2/1.
<Sysname> system-view
[Sysname] interface ethernet 2/1
[Sysname-Ethernet2/1] stp role-restriction
stp root primary
Use stp root primary to configure the device as the root bridge.
Use undo stp root to restore the default.
Syntax
stp [ instance instance-list ] root primary
undo stp [ instance instance-list ] root
Default
A device is not a root bridge.
Views
System view
Predefined user roles
network-admin
Parameters
instance instance-list: Configures the device as the root bridge in the MSTIs that are specified by an
instance list, in the format of instance-list = { instance-id [ to instance-id ] }&<1-10>, where &<1-10>
indicates that you can specify up to 10 instances or instance ranges. The value range for the instance-id
argument is 0 to 4094, and the value 0 represents the CIST. If you do not specify this option, the
command configures the device as the primary root bridge in the MSTP CIST or as the primary root
bridge of STP or RSTP.
Usage guidelines
Once you specify the device as the root bridge, you cannot change the priority of the device.
Examples
# In MSTP mode, specify the device as the root bridge of MSTI 1.
<Sysname> system-view
[Sysname] stp instance 1 root primary
Related commands
• stp priority
• stp root secondary