HP MSR2000/3000/4000 Router Series Layer 2 - LAN Switching Command Reference
Table Of Contents
- Title Page
- Contents
- MAC address table commands
- Port isolation commands
- Spanning tree commands
- active region-configuration
- check region-configuration
- display stp
- display stp abnormal-port
- display stp bpdu-statistics
- display stp down-port
- display stp history
- display stp region-configuration
- display stp root
- display stp tc
- instance
- region-name
- reset stp
- revision-level
- stp bpdu-protection
- stp bridge-diameter
- stp compliance
- stp config-digest-snooping
- stp cost
- stp edged-port
- stp enable
- stp global config-digest-snooping
- stp global enable
- stp global mcheck
- stp loop-protection
- stp max-hops
- stp mcheck
- stp mode
- stp no-agreement-check
- stp pathcost-standard
- stp point-to-point
- stp port priority
- stp port-log
- stp priority
- stp region-configuration
- stp role-restriction
- stp root primary
- stp root secondary
- stp root-protection
- stp tc-protection
- stp tc-protection threshold
- stp tc-restriction
- stp timer forward-delay
- stp timer hello
- stp timer max-age
- stp timer-factor
- stp transmit-limit
- vlan-mapping modulo
- Loop detection commands
- VLAN commands
- LLDP commands
- display lldp local-information
- display lldp neighbor-information
- display lldp statistics
- display lldp status
- display lldp tlv-config
- lldp admin-status
- lldp check-change-interval
- lldp enable
- lldp encapsulation snap
- lldp fast-count
- lldp global enable
- lldp hold-multiplier
- lldp management-address-format string
- lldp max-credit
- lldp mode
- lldp notification med-topology-change enable
- lldp notification remote-change enable
- lldp timer fast-interval
- lldp timer notification-interval
- lldp timer reinit-delay
- lldp timer tx-interval
- lldp tlv-enable
- Support and other resources
- Index
61
Syntax
default
Views
VLAN interface view
Predefined user roles
network-admin
Usage guidelines
CAUTION:
The default command might interrupt ongoing network services. Make sure you are fully aware of the
impacts of this command when you use it in a live network.
This command might fail to restore the default settings for some commands for reasons such as command
dependencies and system restrictions. Use the display this command in interface view to identify these
commands, and then use their undo forms or follow the command reference to individually restore their
default settings. If your restoration attempt still fails, follow the error message instructions to resolve the
problem.
Examples
# Restore the default settings for VLAN-interface 1.
<Sysname> system-view
[Sysname] interface vlan-interface 1
[Sysname-Vlan-interface1] default
description
Use description to change the description of the VLAN or VLAN interface.
Use undo description to restore the default.
Syntax
description text
undo description
Default
For a VLAN, the description is VLAN vlan-id, which specifies the ID of the VLAN. For example, the default
description of VLAN 100 is VLAN 0100.
For a VLAN interface, the description is the name of the interface. For example, Vlan-interface1
Interface.
Views
VLAN view, VLAN interface view
Predefined user roles
network-admin
Parameters
text: Specifies a description for a VLAN or VLAN interface. The string can include case-sensitive letters,
digits, special characters such as tilde (~), exclamation point (!), at sign (@), pound sign (#), dollar sign