HP MSR2000/3000/4000 Router Series Layer 2 - LAN Switching Command Reference
Table Of Contents
- Title Page
- Contents
- MAC address table commands
- Port isolation commands
- Spanning tree commands
- active region-configuration
- check region-configuration
- display stp
- display stp abnormal-port
- display stp bpdu-statistics
- display stp down-port
- display stp history
- display stp region-configuration
- display stp root
- display stp tc
- instance
- region-name
- reset stp
- revision-level
- stp bpdu-protection
- stp bridge-diameter
- stp compliance
- stp config-digest-snooping
- stp cost
- stp edged-port
- stp enable
- stp global config-digest-snooping
- stp global enable
- stp global mcheck
- stp loop-protection
- stp max-hops
- stp mcheck
- stp mode
- stp no-agreement-check
- stp pathcost-standard
- stp point-to-point
- stp port priority
- stp port-log
- stp priority
- stp region-configuration
- stp role-restriction
- stp root primary
- stp root secondary
- stp root-protection
- stp tc-protection
- stp tc-protection threshold
- stp tc-restriction
- stp timer forward-delay
- stp timer hello
- stp timer max-age
- stp timer-factor
- stp transmit-limit
- vlan-mapping modulo
- Loop detection commands
- VLAN commands
- LLDP commands
- display lldp local-information
- display lldp neighbor-information
- display lldp statistics
- display lldp status
- display lldp tlv-config
- lldp admin-status
- lldp check-change-interval
- lldp enable
- lldp encapsulation snap
- lldp fast-count
- lldp global enable
- lldp hold-multiplier
- lldp management-address-format string
- lldp max-credit
- lldp mode
- lldp notification med-topology-change enable
- lldp notification remote-change enable
- lldp timer fast-interval
- lldp timer notification-interval
- lldp timer reinit-delay
- lldp timer tx-interval
- lldp tlv-enable
- Support and other resources
- Index
63
description: Displays the full description of the specified interface. If the keyword is not specified, the
command displays at most the first 27 characters of the interface description. If the keyword is specified,
the command displays all characters of the interface description.
Examples
# Display information for VLAN-interface 10.
<Sysname> display interface vlan-interface 10
Vlan-interface10
Current state: UP
Line protocol state: UP
Description: Vlan-interface10 Interface
Bandwidth: 100000kbps
Maximum Transmit Unit: 1500
Internet Address is 192.168.1.54/24 Primary
IP Packet Frame Type:PKTFMT_ETHNT_2, Hardware Address: 0023-89b6-d613
IPv6 Packet Frame Type:PKTFMT_ETHNT_2, Hardware Address: 0023-89b6-d613
Last clearing of counters: Never
# Display brief information for VLAN-interface 2.
<Sysname> display interface vlan-interface 2 brief
Brief information on interface(s) under route mode:
Link: ADM - administratively down; Stby - standby
Protocol: (s) - spoofing
Interface Link Protocol Main IP Description
Vlan2 DOWN DOWN --
Table 15 Command output
Field Description
Vlan-interface2 VLAN interface name.
Current state
Physical state of a VLAN interface:
• DOWN ( Administratively )—The administrative state of the
VLAN interface is down, because it has been shut down with the
shutdown command.
• DOWN—The administrative state of the VLAN interface is up,
but its physical state is down. The VLAN that corresponds to this
interface does not contain any physical port in the UP state
(possibly because the ports are not well connected or the lines
have failed).
• UP—Both the administrative state and the physical state of the
VLAN interface are up.
Line protocol state
Link layer protocol state of a VLAN interface:
• DOWN—The protocol state of the VLAN interface is down.
• UP—The protocol state of the VLAN interface is up.
Description Description string of a VLAN interface.
Bandwidth Expected bandwidth of a VLAN interface.
Maximum Transmit Unit MTU of a VLAN interface.