HP MSR2000/3000/4000 Router Series Layer 2 - LAN Switching Command Reference
Table Of Contents
- Title Page
- Contents
- MAC address table commands
- Port isolation commands
- Spanning tree commands
- active region-configuration
- check region-configuration
- display stp
- display stp abnormal-port
- display stp bpdu-statistics
- display stp down-port
- display stp history
- display stp region-configuration
- display stp root
- display stp tc
- instance
- region-name
- reset stp
- revision-level
- stp bpdu-protection
- stp bridge-diameter
- stp compliance
- stp config-digest-snooping
- stp cost
- stp edged-port
- stp enable
- stp global config-digest-snooping
- stp global enable
- stp global mcheck
- stp loop-protection
- stp max-hops
- stp mcheck
- stp mode
- stp no-agreement-check
- stp pathcost-standard
- stp point-to-point
- stp port priority
- stp port-log
- stp priority
- stp region-configuration
- stp role-restriction
- stp root primary
- stp root secondary
- stp root-protection
- stp tc-protection
- stp tc-protection threshold
- stp tc-restriction
- stp timer forward-delay
- stp timer hello
- stp timer max-age
- stp timer-factor
- stp transmit-limit
- vlan-mapping modulo
- Loop detection commands
- VLAN commands
- LLDP commands
- display lldp local-information
- display lldp neighbor-information
- display lldp statistics
- display lldp status
- display lldp tlv-config
- lldp admin-status
- lldp check-change-interval
- lldp enable
- lldp encapsulation snap
- lldp fast-count
- lldp global enable
- lldp hold-multiplier
- lldp management-address-format string
- lldp max-credit
- lldp mode
- lldp notification med-topology-change enable
- lldp notification remote-change enable
- lldp timer fast-interval
- lldp timer notification-interval
- lldp timer reinit-delay
- lldp timer tx-interval
- lldp tlv-enable
- Support and other resources
- Index
65
Syntax
display vlan [ vlan-id1 [ to vlan-id2 ] | all | dynamic | reserved | static ]
Views
Any view
Predefined user roles
network-admin
network-operator
Parameters
vlan-id1: Displays information about a VLAN specified by its VLAN ID. The value range for this argument
is 1 to 4094.
vlan-id1 to vlan-id2: Displays information about VLANs that are specified by a VLAN ID range. The
vlan-id1 and vlan-id2 arguments specify VLAN IDs. The value range for each of the two arguments is 1
to 4094. The vlan-id1 argument cannot be greater than the vlan-id2 argument.
all: Displays all VLAN information except for the reserved VLANs.
dynamic: Displays the number of dynamic VLANs and the ID for each dynamic VLAN. The dynamic
VLANs are distributed by a RADIUS server.
reserved: Displays information about the reserved VLANs. Protocol modules determine which VLANs are
reserved VLANs according to function implementation, and reserved VLANs serve protocol modules.
You cannot configure reserved VLANs.
static: Displays the number of static VLANs and the ID for each static VLAN. The static VLANs are
manually created.
Examples
# Display VLAN 2 information.
<Sysname> display vlan 2
VLAN ID: 2
VLAN type: Static
Route interface: Not configured
Description: VLAN 0002
Name: VLAN 0002
Tagged ports: None
Untagged ports:
Ethernet2/1 Ethernet2/2 Ethernet2/3
# Display VLAN 3 information.
<Sysname> display vlan 3
VLAN ID: 3
VLAN type: static
Route interface: Configured
IP address: 1.1.1.1
Subnet mask: 255.255.255.0
Description: VLAN 0003
Name: VLAN 0003
Tagged ports: None
Untagged ports: None