HP MSR2000/3000/4000 Router Series Layer 2 - LAN Switching Command Reference
Table Of Contents
- Title Page
- Contents
- MAC address table commands
- Port isolation commands
- Spanning tree commands
- active region-configuration
- check region-configuration
- display stp
- display stp abnormal-port
- display stp bpdu-statistics
- display stp down-port
- display stp history
- display stp region-configuration
- display stp root
- display stp tc
- instance
- region-name
- reset stp
- revision-level
- stp bpdu-protection
- stp bridge-diameter
- stp compliance
- stp config-digest-snooping
- stp cost
- stp edged-port
- stp enable
- stp global config-digest-snooping
- stp global enable
- stp global mcheck
- stp loop-protection
- stp max-hops
- stp mcheck
- stp mode
- stp no-agreement-check
- stp pathcost-standard
- stp point-to-point
- stp port priority
- stp port-log
- stp priority
- stp region-configuration
- stp role-restriction
- stp root primary
- stp root secondary
- stp root-protection
- stp tc-protection
- stp tc-protection threshold
- stp tc-restriction
- stp timer forward-delay
- stp timer hello
- stp timer max-age
- stp timer-factor
- stp transmit-limit
- vlan-mapping modulo
- Loop detection commands
- VLAN commands
- LLDP commands
- display lldp local-information
- display lldp neighbor-information
- display lldp statistics
- display lldp status
- display lldp tlv-config
- lldp admin-status
- lldp check-change-interval
- lldp enable
- lldp encapsulation snap
- lldp fast-count
- lldp global enable
- lldp hold-multiplier
- lldp management-address-format string
- lldp max-credit
- lldp mode
- lldp notification med-topology-change enable
- lldp notification remote-change enable
- lldp timer fast-interval
- lldp timer notification-interval
- lldp timer reinit-delay
- lldp timer tx-interval
- lldp tlv-enable
- Support and other resources
- Index
71
Views
System view
Predefined user roles
network-admin
Parameters
vlan-id1, vlan-id2: Specifies a VLAN ID. The value range is 1 to 4094.
vlan-id1 to vlan-id2: Specifies a VLAN range. The vlan-id1 and vlan-id2 arguments specify VLAN IDs.
The value range for each of the two arguments is 1 to 4094. The vlan-id1 argument cannot be greater
than vlan-id2.
all: Creates or removes all VLANs except reserved VLANs. The keyword is not supported when the
maximum number of VLANs that can be created on a device is less than 4094.
Usage guidelines
You cannot create or remove the default VLAN (VLAN 1).
You cannot create or remove VLANs that are reserved for specific functions.
You cannot use the undo vlan command to delete a dynamic VLAN, a VLAN with a QoS policy applied,
or a VLAN locked by an application. To delete such a VLAN, first remove the configuration from the
VLAN.
Examples
# Create VLAN 2 and enter its view.
<Sysname> system-view
[Sysname] vlan 2
[Sysname-vlan2]
# Create VLAN 4 through VLAN 100.
<Sysname> system-view
[Sysname] vlan 4 to 100
Related commands
display vlan
Port-based VLAN commands
display port
Use display port to display information about the hybrid or trunk ports on the device, including the port
names, PVIDs, and allowed VLAN IDs.
Syntax
display port { hybrid | trunk }
Views
Any view
Predefined user roles
network-admin