HP MSR2000/3000/4000 Router Series Layer 2 - LAN Switching Command Reference
Table Of Contents
- Title Page
- Contents
- MAC address table commands
- Port isolation commands
- Spanning tree commands
- active region-configuration
- check region-configuration
- display stp
- display stp abnormal-port
- display stp bpdu-statistics
- display stp down-port
- display stp history
- display stp region-configuration
- display stp root
- display stp tc
- instance
- region-name
- reset stp
- revision-level
- stp bpdu-protection
- stp bridge-diameter
- stp compliance
- stp config-digest-snooping
- stp cost
- stp edged-port
- stp enable
- stp global config-digest-snooping
- stp global enable
- stp global mcheck
- stp loop-protection
- stp max-hops
- stp mcheck
- stp mode
- stp no-agreement-check
- stp pathcost-standard
- stp point-to-point
- stp port priority
- stp port-log
- stp priority
- stp region-configuration
- stp role-restriction
- stp root primary
- stp root secondary
- stp root-protection
- stp tc-protection
- stp tc-protection threshold
- stp tc-restriction
- stp timer forward-delay
- stp timer hello
- stp timer max-age
- stp timer-factor
- stp transmit-limit
- vlan-mapping modulo
- Loop detection commands
- VLAN commands
- LLDP commands
- display lldp local-information
- display lldp neighbor-information
- display lldp statistics
- display lldp status
- display lldp tlv-config
- lldp admin-status
- lldp check-change-interval
- lldp enable
- lldp encapsulation snap
- lldp fast-count
- lldp global enable
- lldp hold-multiplier
- lldp management-address-format string
- lldp max-credit
- lldp mode
- lldp notification med-topology-change enable
- lldp notification remote-change enable
- lldp timer fast-interval
- lldp timer notification-interval
- lldp timer reinit-delay
- lldp timer tx-interval
- lldp tlv-enable
- Support and other resources
- Index
73
Parameters
interface-list: Specifies an interface list, in the format of interface-list = { interface-type interface-number
[ to interface-type interface-number ] }&<1-10>, where interface-type interface-number represents the
interface type and interface number, and &<1-10> indicates that you can specify up to 10 interface-type
interface-number [ to interface-type interface-number ] parameters.
Usage guidelines
This command is applicable only on access ports.
By default, all ports are access ports. However, you can manually configure the port type. For more
information, see "port link-type."
Examples
# Assign Ethernet 2/1 through Ethernet 2/3 to VLAN 2.
<Sysname> system-view
[Sysname] vlan 2
[Sysname-vlan2] port ethernet 2/1 to ethernet 2/3
Related commands
display vlan
port access vlan
Use port access vlan to assign the access ports to the specified VLAN.
Use undo port access vlan to restore the default.
Syntax
port access vlan vlan-id
undo port access vlan
Default
All access ports belong to VLAN 1.
Views
Layer 2 Ethernet interface view
Predefined user roles
network-admin
Parameters
vlan-id: Specifies a VLAN ID in the range of 1 to 4094. Make sure the VLAN specified by the VLAN ID
already exists.
Usage guidelines
Before assigning an access port to a VLAN, make sure the VLAN has been created.
The configuration made in Layer 2 Ethernet interface view applies only to the port.
Examples
# Assign Ethernet 2/1 to VLAN 3.
<Sysname> system-view
[Sysname] vlan 3