HP MSR2000/3000/4000 Router Series Layer 2 - LAN Switching Command Reference
Table Of Contents
- Title Page
- Contents
- MAC address table commands
- Port isolation commands
- Spanning tree commands
- active region-configuration
- check region-configuration
- display stp
- display stp abnormal-port
- display stp bpdu-statistics
- display stp down-port
- display stp history
- display stp region-configuration
- display stp root
- display stp tc
- instance
- region-name
- reset stp
- revision-level
- stp bpdu-protection
- stp bridge-diameter
- stp compliance
- stp config-digest-snooping
- stp cost
- stp edged-port
- stp enable
- stp global config-digest-snooping
- stp global enable
- stp global mcheck
- stp loop-protection
- stp max-hops
- stp mcheck
- stp mode
- stp no-agreement-check
- stp pathcost-standard
- stp point-to-point
- stp port priority
- stp port-log
- stp priority
- stp region-configuration
- stp role-restriction
- stp root primary
- stp root secondary
- stp root-protection
- stp tc-protection
- stp tc-protection threshold
- stp tc-restriction
- stp timer forward-delay
- stp timer hello
- stp timer max-age
- stp timer-factor
- stp transmit-limit
- vlan-mapping modulo
- Loop detection commands
- VLAN commands
- LLDP commands
- display lldp local-information
- display lldp neighbor-information
- display lldp statistics
- display lldp status
- display lldp tlv-config
- lldp admin-status
- lldp check-change-interval
- lldp enable
- lldp encapsulation snap
- lldp fast-count
- lldp global enable
- lldp hold-multiplier
- lldp management-address-format string
- lldp max-credit
- lldp mode
- lldp notification med-topology-change enable
- lldp notification remote-change enable
- lldp timer fast-interval
- lldp timer notification-interval
- lldp timer reinit-delay
- lldp timer tx-interval
- lldp tlv-enable
- Support and other resources
- Index
74
[Sysname-vlan3] quit
[Sysname] interface ethernet 2/1
[Sysname-Ethernet2/1] port access vlan 3
port hybrid pvid
Use port hybrid pvid to configure the PVID of the hybrid port.
Use undo port hybrid pvid to restore the default.
Syntax
port hybrid pvid vlan vlan-id
undo port hybrid pvid
Default
The PVID of a hybrid port is VLAN 1.
Views
Layer 2 Ethernet interface view
Predefined user roles
network-admin
Parameters
vlan-id: Specifies a VLAN ID in the range of 1 to 4094.
Usage guidelines
You can use a nonexistent VLAN as the PVID for a hybrid port. If you remove the PVID of a hybrid port
with the undo vlan command, the setting of the PVID on the port is not affected.
HP recommends that you set the same PVID for the local and remote hybrid ports.
You must configure the hybrid port to allow and forward packets from the PVID by using the port hybrid
vlan command.
The configuration made in Layer 2 Ethernet interface view applies only to the port.
Examples
# Configure VLAN 100 as the PVID of the hybrid port Ethernet 2/1, and assign Ethernet 2/1 to VLAN
100.
<Sysname> system-view
[Sysname] vlan 100
[Sysname-vlan100] quit
[Sysname] interface ethernet 2/1
[Sysname-Ethernet2/1] port link-type hybrid
[Sysname-Ethernet2/1] port hybrid pvid vlan 100
[Sysname-Ethernet2/1] port hybrid vlan 100 untagged
Related commands
• port hybrid vlan
• port link-type