HP MSR2000/3000/4000 Router Series Layer 2 - LAN Switching Command Reference
Table Of Contents
- Title Page
- Contents
- MAC address table commands
- Port isolation commands
- Spanning tree commands
- active region-configuration
- check region-configuration
- display stp
- display stp abnormal-port
- display stp bpdu-statistics
- display stp down-port
- display stp history
- display stp region-configuration
- display stp root
- display stp tc
- instance
- region-name
- reset stp
- revision-level
- stp bpdu-protection
- stp bridge-diameter
- stp compliance
- stp config-digest-snooping
- stp cost
- stp edged-port
- stp enable
- stp global config-digest-snooping
- stp global enable
- stp global mcheck
- stp loop-protection
- stp max-hops
- stp mcheck
- stp mode
- stp no-agreement-check
- stp pathcost-standard
- stp point-to-point
- stp port priority
- stp port-log
- stp priority
- stp region-configuration
- stp role-restriction
- stp root primary
- stp root secondary
- stp root-protection
- stp tc-protection
- stp tc-protection threshold
- stp tc-restriction
- stp timer forward-delay
- stp timer hello
- stp timer max-age
- stp timer-factor
- stp transmit-limit
- vlan-mapping modulo
- Loop detection commands
- VLAN commands
- LLDP commands
- display lldp local-information
- display lldp neighbor-information
- display lldp statistics
- display lldp status
- display lldp tlv-config
- lldp admin-status
- lldp check-change-interval
- lldp enable
- lldp encapsulation snap
- lldp fast-count
- lldp global enable
- lldp hold-multiplier
- lldp management-address-format string
- lldp max-credit
- lldp mode
- lldp notification med-topology-change enable
- lldp notification remote-change enable
- lldp timer fast-interval
- lldp timer notification-interval
- lldp timer reinit-delay
- lldp timer tx-interval
- lldp tlv-enable
- Support and other resources
- Index
81
Field Descri
p
tion
System capabilities supported
Supported capabilities:
• Bridge—Switching is supported.
• Router—Routing is supported.
• Customer Bridge—The customer bridge function is supported.
• Service Bridge—The service bridge function is supported.
System capabilities enabled
Enabled capabilities:
• Bridge—Switching is enabled.
• Router—Routing is enabled.
• Customer Bridge—The customer bridge function is enabled.
• Service Bridge—The service bridge function is enabled.
Device class
MED device class:
• Connectivity device—Network device.
• Class I—Normal terminal device. It requires the basic LLDP discovery
services.
• Class II—Media terminal device. It supports media streams, and can
also function as a normal terminal device.
• Class III—Communication terminal device. It supports the IP
communication systems of end users, and can also function as a normal
terminal device or media terminal device.
HardwareRev Hardware version.
FirmwareRev Firmware version.
SoftwareRev Software version.
SerialNum Serial number.
Manufacturer name Device manufacturer.
Model name Device model.
Port ID type
Port ID type:
• MAC address.
• Interface name.
Port ID Port ID, the value of which depends on the port ID type.
Management address interface
type
Numbering type of the interface identified by the management address.
Management address interface
ID
Index of the interface identified by the management address.
Management address OID Management address object ID.
DCBX control info Displayed as version information in IEEE Std 802.1Qaz™-2011.
Oper version DCBX version number.
Sequence number Number of DCBX TLV content changes.
Acknowledge number Times of synchronizing configurations by the peer device.
DCBX ETS info CoS-to-local priority mapping and bandwidth allocation.
Percentage Percentage of bandwidth allocated.