Manualshelf

R0106-HP MSR Router Series Layer 3 - IP Routing Configuration Guide(V7)

ManualsBrandsHP ManualsNetwork HardwareHP MSR3024 TAA-compliant AC Router
51525354555657585960
47
12.3.1.0/24 Direct 0 0 12.3.1.2 GE2/1/1
12.3.1.0/32 Direct 0 0 12.3.1.2 GE2/1/1
12.3.1.2/32 Direct 0 0 127.0.0.1 InLoop0
12.3.1.255/32 Direct 0 0 12.3.1.2 GE2/1/1
16.4.1.0/24 Direct 0 0 16.4.1.1 GE2/1/2
16.4.1.0/32 Direct 0 0 16.4.1.1 GE2/1/2
16.4.1.1/32 Direct 0 0 127.0.0.1 InLoop0
16.4.1.255/32 Direct 0 0 16.4.1.1 GE2/1/2
127.0.0.0/8 Direct 0 0 127.0.0.1 InLoop0
127.0.0.0/32 Direct 0 0 127.0.0.1 InLoop0
127.0.0.1/32 Direct 0 0 127.0.0.1 InLoop0
127.255.255.255/32 Direct 0 0 127.0.0.1 InLoop0
3. Configure RIP route redistribution:
# Configure RIP 200 to redistribute direct routes and routes from RIP 100 on Router B.
[RouterB] rip 200
[RouterB-rip-200] import-route rip 100
[RouterB-rip-200] import-route direct
[RouterB-rip-200] quit
# Display the IP routing table on Router C.
[RouterC] display ip routing-table
Destinations : 15 Routes : 15
Destination/Mask Proto Pre Cost NextHop Interface
0.0.0.0/32 Direct 0 0 127.0.0.1 InLoop0
10.2.1.0/24 RIP 100 1 12.3.1.1 GE2/1/1
11.1.1.0/24 RIP 100 1 12.3.1.1 GE2/1/1
12.3.1.0/24 Direct 0 0 12.3.1.2 GE2/1/1
12.3.1.0/32 Direct 0 0 12.3.1.2 GE2/1/1
12.3.1.2/32 Direct 0 0 127.0.0.1 InLoop0
12.3.1.255/32 Direct 0 0 12.3.1.2 GE2/1/1
16.4.1.0/24 Direct 0 0 16.4.1.1 GE2/1/2
16.4.1.0/32 Direct 0 0 16.4.1.1 GE2/1/2
16.4.1.1/32 Direct 0 0 127.0.0.1 InLoop0
16.4.1.255/32 Direct 0 0 16.4.1.1 GE2/1/2
127.0.0.0/8 Direct 0 0 127.0.0.1 InLoop0
127.0.0.0/32 Direct 0 0 127.0.0.1 InLoop0
127.0.0.1/32 Direct 0 0 127.0.0.1 InLoop0
127.255.255.255/32 Direct 0 0 127.0.0.1 InLoop0
127.0.0.1/32 Direct 0 0 127.0.0.1 InLoop0
Configuring an additional metric for a RIP interface
Network requirements
As shown in Figure 9, run RIPv2 on all the interfaces of Router A, Router B, Router C, Router D, and Router
E.