HP NC310F PCI-X Gigabit Server Adapter User Guide June 2007 (Third Edition) Part Number 367258-00C
©2004, 2007 Hewlett-Packard Development Company, L.P. Intel® is a trademark of Intel Corporation in the U.S. and other countries. Hewlett-Packard Development Company, L.P. shall not be liable for technical or editorial errors or omissions contained herein. The information in this document is provided “as is” without warranty of any kind and is subject to change without notice. The warranties for HP products are set forth in the express limited warranty statements accompanying such products.
Contents About This Guide Technician Notes...........................................................................................................................................v Where to Go for Additional Help.................................................................................................................vi Telephone Numbers ...............................................................................................................................
About This Guide This guide can be used for reference when installing the NC 310F PCI-X Gigabit Server Adapter. WARNING: To reduce the risk of personal injury from electric shock and hazardous energy levels, only authorized service technicians should attempt to repair this equipment. Improper repairs can create conditions that are hazardous. Technician Notes WARNING: Only authorized technicians trained by HP should attempt to repair this equipment.
About This Guide NOTE: Any indications of component replacement or printed wiring board modifications may void any warranty. Where to Go for Additional Help HP updates networking software frequently to include new functionality and features. Complete the following steps to get the latest drivers, firmware, and documentation. 1. Go to the HP website (http://www.hp.com). 2. Click Support and Troubleshooting Information from the left menu bar. 3. Type the product name in the for product box and press Enter.
1 Introduction Overview The HP NC310F PCI-X Gigabit Server Adapter is a high performance, stand-alone Ethernet adapter with a controller chip that delivers 1000 Mb/s Ethernet over fiber cabling. For best performance, install the adapter in a 64-bit/133MHz, PCI-X slot. The adapter provides failover capabilities with other Gigabit and 10/100 adapters installed in the workstation or server. The HP NC310F PCI-X Gigabit Server Adapter supports current standards for IEEE 802.
Introduction LED Indicator The adapter has a single fiber LC port and LED indicator for activity/link. Figure 1-1: NC310F PCI-X Gigabit Server Adapter The HP NC310F PCI-X Gigabit Server Adapter LED indicator operates as described in the following table. Table 1-1: LED Operation for the HP NC310F PCI-X Gigabit Server Adapter 1-2 LED Status Description ACT/LNK On When green, link to the adapter is established. The adapter is receiving power and the cable connection is secure.
2 Installing the Adapter Overview This chapter describes installation precautions, how to install the adapter, and how to attach the fiber network cable. WARNING: To avoid the risk of personal injury or damage to the equipment, consult the safety information and user documentation provided with your equipment before attempting installation of the adapter. Many servers are capable of producing energy levels that are considered hazardous.
Installing the Adapter Installing the Adapter in a Server Refer to the HP ProLiant server documentation for additional information on how to safely install a PCI card in the server. Figure 2-1: Installing the adapter in a server WARNING: If the server is not PCI Hot Plug compliant, power it down and unplug the power cord from the power outlet before removing the server cover. Failure to do so may damage the adapter or server. 1. Remove the power cord and server cover.
A Regulatory Compliance Notice European Notice Products bearing the CE marking comply with the EMC Directive (89/336/EEC) and the Low Voltage Directive (73/23/EEC) issued by the Commission of the European Community, and if this product has telecommunication functionality, the R&TTE Directive (1999/5/EC).
Regulatory Compliance Notice Korean Notice Laser Compliance The fiber optic module contains a laser that is classified as a “Class 1 Laser Product” in accordance with US FDA regulations and the IEC 60825-1. The product does not emit hazardous laser radiation. WARNING: Use of controls or adjustments or performance of procedures other than those specified herein or in the laser product’s installation guide may result in hazardous radiation exposure.
B Electrostatic Discharge Overview To prevent damage to the system, be aware of the precautions you need to follow when setting up the system or handling parts. A discharge of static electricity from a finger or other conductor may damage system boards or other static-sensitive devices. This type of damage may reduce the life expectancy of the device. To prevent electrostatic damage, observe the following precautions: • Avoid hand contact by transporting and storing products in static-safe containers.
C Specifications HP NC310F PCI-X Gigabit Server Adapter Specifications Table C-1: NC310F PCI-X Gigabit Server Adapter Specifications Specification Description Network Controller Chipset Intel® 82545GM MAC/Phy/SERDES Bus Type PCI-X/PCI Bus Width 32- or 64-bit Bus Speed (MHz) 33/66/100/133 Data Transfer Method Bus Master DMA On-board Memory 64 KB Power Requirement 480 mA @ 5V max Data Transmission Rate 1000 Mb/s (Full-duplex) Standards Supported IEEE 802.3z, 802.3x, 802.1p, 802.1Q, 802.
Specifications Fiber Cable Specifications To connect to the network, the NC310F PCI-X Gigabit Server Adapter uses a 1000Base-SX fiber transeiver with an LC fiber connector. Table C-2 describes the mode, cable size, and maximum distance specifications for this adapter. Table C-2: Fiber Cable Maximum Distances for 1000Base-SX C-2 Mode Size Max Distance Multimode 62.
