HP Netserver E 30 Installation Roadmap

1
Verify Contents
To obtain drivers and utilities for non-HP components of your system, follow the appropriate Internet, BBS, or CompuServe procedure specified by the
component and network operating system manufacturers.
1. Press the power-on button. Open the NetServer front door and press the CD-ROM drive eject button. Place the HP NetServer Navigator CD-ROM in
the drive and press the eject button again to close the drive. If the NetServer doesn't boot from the Navigator CD-ROM, turn the power off, wait 10
seconds and turn the power on again. If the system fails to boot, follow the diagnostic instructions on the screen.
2. Go to the HP NetServer Navigator Main Menu. If the language needs to be changed, select "Set Preferences."
3. Select "Readme File."
You can run Diagnostic Assistant now from the Navigator CD-ROM if you want to verify system operation as shipped.
4. If you are installing additional hardware, such as memory, accessory boards, or mass storage devices, you will need to remove the cover.
Go to Step 4: "Remove the Cover."
If you are not installing additional hardware, go to Step 8: "Configure the HP NetServer."
The Readme file contains the latest information to help you install your HP NetServer. Read it carefully before
beginning your installation.
1. Check that the correct voltage is set for your country. (The voltage
is set during manufacturing and should already be correct.)
2. Connect the monitor, keyboard and mouse to the HP NetServer
and plug in the power cords to the NetServer and to the monitor.
3. If you have a UPS (Uninterruptible Power Supply), install and turn
on the UPS. Use the supplied serial cable to connect the UPS to
the HP NetServer. Refer to the user’s guide included with the
UPS for additional information.
4. Plug in both the NetServer and monitor power cords to the power
supply.
3
2
View the Readme File
Set Voltage Switch, Connect Monitor, Keyboard, and Mouse
4
Remove the Cover
If you are installing options, you will need to remove the cover. To install options, you
will need a flat 1/4-inch screwdriver and T15 TORX® driver; you do not need tools to
remove the cover.
1. Turn off the NetServer and disconnect the power cord.
2. Check if the NetServer is locked (see figure). If locked, unlock the
cover using the key in the key bag located on the rear of the
NetServer.
3. Lift up the two release latches on the sides of the front bezel.
WARNING Before removing the cover, always disconnect the
power cord and unplug telephone cables. Disconnect
telephone cables to avoid exposure to shock hazard
from telephone ringing voltages. Disconnect the
power cord to avoid exposure to high energy levels
that may cause burns when parts are short-circuited
by metal objects such as tools or jewelry.
CAUTION Wear a wrist strap and use a static-dissipative work
surface connected to the chassis when handling
components.
Unpack and verify the contents of the shipping box against the Contents Checklist included with your NetServer. If anything is missing or damaged,
call your reseller.
To ensure that you have the latest versions of the software, obtain the current Release History. This report describes m
Obtain the Release History in one of these ways:
HP NetServer Navigator CD Release History
ajor software updates to each
release of the HP Navigator CD-ROM and instructions for obtaining a current release.
!
!
!
!
!
Fax:
Internet WWW:
Internet FTP:
BBS:
CompuServe:
Call HP’s fax system at 1-800-333-1917(or 1-208-344-4809 from your fax machine) and request Document Number 6005
http://www.hp.com/go/netserver
ftp.netserver.hp.com;logon:anonymous; password: <your e-mail address> cd NSNAVCD; get 6005.txt
Call 1-408-553-3500; download 6005.txt from NSNAVCD library
GO HPPC; download 6005.txt from the NetServer library
Power cord from
HP NetServer
Power cord
from Monitor
To Serial Port of
HP NetServer
UPS
Key
Lock
Release
Latches
When replacing the
cover, ensure that the
bottom rear corners of
the cover mate with the
grooves on the chassis
Voltage
Setting
Monitor
Mouse
Serial
Ports
Parallel
Port
Network
Connection
Power
Keyboard
On/Off
Switch and
Power/
ActivityLED
CD-ROM
Drive
Flexible
Disk Drive
Door
Chassis
Cover