HP Netserver LH 6000 Technical Reference Card

HP NetServer LH 6000 / LH 6000r Technical Reference Card
HP Product No. D9103-80201, Feb. 2000
Cabling: Power
E
Cabling: Data
To Optional Mass Storage Device
SCSI A
SCSI B
Front Panel
Display
Flexible
Disk Drive
IDE
CD-ROM
Secondary (Optional) Hot-Swap
Mass Storage Cage
Primary Hot-Swap Mass
Storage Cage
I/O Board
Power Management/Interconnection Board
= on backside of Pwr Mgmnt/Intercnct
To Management Port
Connector (I/O Board)
To OLx Connector
(I/O board)
PCI Attention LEDs
(Hot-Swap)
Power Supply
Redundant Power Supply
To Non Hot-Swap
Mass Storage
Flexible Disk Drive
IDE CD-ROM
4W
4W
14W
14W
2W
To Secondary (Optional)
Hot-Swap Mass Storage Cage
To Primary Hot-Swap
Mass Storage Cage
Power Supply Control Cable
Power Management/Interconnection Board
Rear of Unit
3
4
2
1
PS1
PS2
PS3
PS4
To rear panel OLx board
Cable P/O Panel
To rear panel
Management Port
Cable P/O Display
I/O Board
F
PCI Slots 1-6: +5V, 33 MHz,
32- or 64 Bit
1
2
3
4
5
6
7
8
Card Retainer
and Lever
(1 of 8)
Remote
Management
PCI Slots 7, 8:
+3.3V or
Universal,*
33/66 MHz,
32- or 64-Bit
Attention LED
(Amber)
Power LED (Green)
PCI Slot
Separator
Hot-Plug Slots (5 - 8)
* A “Universal Card” accepts either 3.3V
or 5V and is keyed to fit slots 7 & 8.
Non-Hot-Plug Slots (1 - 4)
OLx Connector
Location of
OLx Board
I/O Memory (for NetRAID 32MB,
64MB or 128MB Cache)
SE SCSI
Connector
I/O Fan
(Removed)
Blind Mate
Fan
Connector
SCSI A
Connector
SCSI B
Connector
I/O Fan
PCI Slot
Separator
(1 of 4)
Hot-Swap Mass Storage Configurations
G
1.6˝ Half-Height (HH)
Drive
1˝ Low-Profile (LP)
Drive
.5˝ Drive Spacer
Key
3 HH
2
0
8
A
SCSI A
6 LP
8
3
2
1
0
9
6 LP
1
0
2
1
0
AB
2
2 LP, HH, 2 LP
8
1
0
2
A
9
HH, LP Alt.
2
2
0
A
9
HH, LP, HH, LP
2
0
0
AB
2
1 HH, 4 LP
8
3
2
0
A
9
1 HH, 4 LP
1
0
2
0
AB
2
2 HH, 2 LP
8
2
0
A
9
Simplex SCSI Addressing (One Cage)
Duplex SCSI Addressing (One Cage)
• Ensure Hot-Swap drives are installed in lowest
or left-most slot first.
• Use SCSI A only for Primary Cage, SCSI B only
for Secondary Cage.
• For duplex configurations, install duplex board
and reconfigure as shown in the 3 diagrams at
right.
• Pedestal configurations are shown here. For Rack
configurations, rotate diagrams 90º clockwise.
• All 1.6˝ Drives require the use of a .5˝ Drive Spacer.
For additional information, see other side.