HP Netserver LC 2000 Technical Reference Card

HP NetServer LC 2000 & LC 2000r Technical Reference Card
Audience Assumptions
This Technical Reference Card is for
trained service personnel. Hewlett-Packard
Company assumes you are qualified in the
servicing of computer equipment and trained
in recognizing hazards in products with
hazardous energy levels.
Electrostatic Discharge
To avoid catastrophic or hidden damage to
components, wear a wrist strap and use a
static-dissipative work surface connected to
the chassis when handling components. Use
an antistatic service kit, such as 3M
8501/8502/8505 or equivalent.
This information is subject to change without
notice and is provided without warranty.
© copyright 1999, Hewlett-Packard
For additional information, see other side.
SCSI Hot-Swap HDD Configurations
Key
D
1.6˝ Half-Height (HH) drive
1˝ Low Profile (LP) drive
.5˝ Drive Spacer
2 LP-HH-2LP
9
8
1
0
2
9
8
3
2
1HH-4LP
0
3 HH
0
2
8
9
8
2HH-2LP
0
2
6 LP
9
8
3
2
1
0
HDD Slot
6
5
4
3
2
1
SCSI ID
HDD Slot
6
5
4
3
2
1
Alternating
HH-LP
9
3
0
2
Hot-Swap Mass Storage
Configurations
• Ensure hot-swap drives are
installed in lowest (pedestal)
or left-most (rack) slot first.
• Use only HP Ultra-2 (LVD)
SCSI 3.5-inch HDDs.
• You may mix or match Low
Profile (LP–1-inch) and Half-
Height (HH–1.6-inch) HHD.
• For rack-mounted models,
rotate diagrams 90˚ clockwise
SCSI ID
Shown Here
Power Supply Cabling
F
Fan Module (Removed)
System Board
Fan Module
Power Connector
C
P
4
P
5
P
4
P
5
P4
P4
P3
Mass Storage
Power Connector
Optional
Redundant Power
Supply Connectors
P1
P2
P5
P6
P1
P5
P2
P3
P1, P2, and P3 are
connected to power
supplies below/behind
P4 and P5
IDE CD-ROM Drive
Flexible Disk Drive
Front Panel
Display
Hot-Swap Mass
Storage Drives
Non-Hot-Swap Mass
Storage Units
Mass Storage Cabling
E
IDE CD-ROM
Connector
Fan Module
(Removed)
System Board
Front Panel
Connector
1
2
3 4
5
5
SCSI B
Connector
SCSI A
Connector
Flexible
Disk Drive
Connector
C
1
2
6
6
3
3
4
Mass Storage
Cage
IDE CD-ROM Drive
Flexible Disk
Drive
Front Panel
Display
Hot-Swap
Mass Storage
Drives
Optional
Non-Hot-
Swap Mass
Storage Units
1
2
3
4
5
6
Cables
FDD Cable
Unterminated SCSI Cable from
System Board to Hot-Swap Bay
(See Notes 1 & 2).
Terminated SCSI Cable from System
Board to Common Tray Devices.
DO NOT CONNECT TO HOT-SWAP
BAY. (See Notes 1 & 2)
IDE CD-ROM Cable
Control Panel Cable
SCSI Cable for Hot-Swap
Note 1: Connectors on cables and
must be plugged into the
correct connector, as shown
on labeled cable-ends.
Note 2: Cables and are not
interchangeable. Cable is
unterminated, cable is
terminated. Data corruption
will occur unless cables are
connected as shown.
Note 3: Further details in the
Installation Guide.
3
2
3
2
3
2
Built-in SCSI Terminator
Service Information
Electronic Support Services
• Internet Web Pages http://www.hp.com/netserver
• Internet FTP ftp://ftp.netserver.hp.com
• CompuServe Library GO HPPC
• HP Navigator CD
Support Questions
• HP-Authorized Reseller
• CompuServe Discussion Forum GO HPPC
• US / Canada Phone Support 1-208-331-2767
• Europe Phone Support ([phone]
(Netherlands)
HP has offices in over 100 countries.
Check your local telephone directory.
G
HP Product No. D8514-80201, REV B, Sept. 1999