HP Netserver LH 4 Installation Road Map

NOTE If you install an ISA non-Plug-and-Play board,
you must reserve system resources (some or
all of: memory addresses, I/O addresses,
IRQs, and DMA channels) for it. Write down
that information now for reference when you
reserve system resouces in Panel 12:
"Configure the HP NetServer."
5
1. Boot the :
2. Read the Readme File
3. Run DiagTools (Optional):
HP NetServer Navigator CD-ROM Turn on
the monitor. Press the power-on button on the HP NetServer,
and press the eject button on the CD-ROM drive. Place the
in the drive, and close the drive.
Press the Reset button. If the system fails to restart, follow the
instructions on the screen.
When HP Navigator starts, you can set the time and date, and
change the display language.
Select "Readme File" from the HP
Navigator Main Menu. The Readme file contains the latest
information to help you install your HP NetServer.
To verify the HP NetServer
hardware as shipped, copy Diag Tools from the
to diskette. Refer to the online
HP
NetServer Navigator CD-ROM
HP NetServer
Navigator CD-ROM
:
Preparation
documentation
for more information.
Information Assistant will help you
install your HP NetServer. It is easier to use from a stand-alone system,
rather than from the HP NetServer you are installing. Install Information
Assistant from the onto
the client system that you will be using to manage your HP NetServer.
on the Internet at
http://www.hp.com/go/netserver
Order Assistant lists HP accessories, cables, and connectors for your
HP NetServer.
HP NetServer DiagTools Error Reference and User
Guide
HP NetServer Online Documentation CD-ROM
4. Install Information Assistant:
5. Visit Order Assistant (optional)
6
If you are installing accessory cards or mass storage devices,
remove the front bezel and cover 1. If you are installing memory,
remove the front bezel and cover 3.
To install some options, you will need a flat 1/4-inch screwdriver
and a T15 TORX driver.
®
Removing and Replacing the Covers
To remove a cover:
and disconnect the power cord
and telephone cord.
with the key from the key bag
located on the rear of the HP NetServer.
pull the top of the bezel away
from the chassis, and then lift the bezel up and off of the chassis.
at the front of the cover and pull
the cover forward, using the handle on the cover, and then lift it
off the chassis.
1. Turn off the HP NetServer
2. Unlock the bezel lock
3. To remove the front bezel,
4. Loosen the thumbscrew
WARNING Before removing cover(s), always disconnect the
power cord and unplug telephone cables.
Note that the power switch does not turn off the
standby power. Disconnect the power cord to turn
off standby power. If the backlight on the LCD
display is on, standby power is on.
CAUTION Wear a wrist strap and use a static-dissipating work
surface connected to the chassis at all times.
To replace a cover:
insert the tabs inside the rear of the cover
into the slots at rear of the chassis and slide the side cover toward the
rear. Tighten the thumbscrew at the front of the cover.
insert the tabs at the bottom of the bezel
into the slots at the bottom of the chassis front and press the top of
the bezel to the chassis until it snaps into place. Lock the bezel lock
with the key provided.
1. To replace a cover,
2. To replace the bezel,
3. Replace all power, telephone, and I/O cables.
Tabs and Slots
Bezel Lock
Unlocked Position
Thumbscrews
Cover 1
Cover 2
Cover 3
Install All Accessory Boards
7
1. Remove cover 1
2. Read the documentation
3. Remove the slot cover
4. Install the boards:
as described in panel 6: "Removing and
Replacing the Covers."
included with each accessory board.
Follow any special instructions and installation recommendations.
Some boards have preferred slot locations. If not, consider the boot
order (see below) when choosing the accessory board socket in
which to install the board.
for each slot to be used, and store it for
future use. If you are installing any full-length PCI boards, also
remove the accessory board retainer. Push on the button on the
retainer to release it, and then slide it out of the board guide.
Insert each board in the desired slot and
fasten the board's mounting screw at the slot opening at the rear of
the chassis. Connect any required cables to the boards. If you
removed the board retainer, reinstall it.
Boot order for PCI controllers is determined by slot location. The
system searches for a bootable device in the following order:
1. IDE CD-ROM drive with a bootable CD-ROM.
2. Flexible disk drive with a bootable flexible disk.
3. Embedded SCSI controller or embedded DAC.
4. PCI boards in slots in the following order: 8, 7, 6, 5, 4, 3, 2, 1.
This boot order can be changed using the SETUP utility
(press [F2] during the boot process).
Boot Device Priority
PCI Board- Left-Side Offset
ISA Board- Right-Side Offset
NOTE For a list of boards HP has tested, see Help
topic "Tested Parts List" on the HP Navigator
CD-ROM.
Accessory
Board
Retainer
Accessory Board
Guide
Release Tab
Slot 1 16-bit ISA or 32-bit PCI
Slot 2 32-bit PCI
Slot 3 32-bit PCI
Slot 4 32-bit PCI
Slot 5 32-bit PCI
Slot 6 32-bit PCI
Slot 7 64-bit PCI
Slot 8 64-bit PCI
Front
Bezel