HP Netserver LH 4r Installation Road Map

ManualsBrandsHP ManualsServerHP NetServer LS

Notice

The information contained in this document is subject to change

without notice.

Hewlett-Packard makes no warranty of any kind with

regard to this material, including, but not limited to, the

implied warranties of merchantability and fitness for a

particular purpose. Hewlett-Packard shall not be liable for

errors contained herein or for incidental or consequential

damages in connection with the furnishing, performance, or use

of this material.

Hewlett-Packard assumes no responsibility for the use or

reliability of its software on equipment that is not furnished by

Hewlett-Packard.

This document contains proprietary information that is protected

by copyright. All rights are reserved. No part of this document

may be photocopied, reproduced, or translated to another

language without the prior written consent of Hewlett-Packard

Company.

Hewlett-Packard Company

Network Server Division

P.O. Box 58059, Technical Marketing

Santa Clara, CA 95052-8059 USA

LH 4r

Installation

Road Map

HP NetServer

5967-6608

Printed on recycled paper.

Printed in November 1998

Audience Assumptions

This road map is intended for the person who installs, administers,

and troubleshoots LAN servers. Hewlett-Packard Company assumes

that you are qualified in the servicing of computer equipment and

trained in recognizing hazards in products with hazardous energy

levels.

ESD Warning

Tools Required

This HP NetServer contains sensitive electronic devices that can be

damaged by electrostatic discharge (ESD). ESD hazards are a result

of installation or service personnel failing to ground themselves

properly. To be properly grounded, use a proper ESD wrist strap and

work surface grounded to the HP NetServer chassis.

Installation of some accessories require a and a T15

TORX or a 1/4-inch flat blade screwdriver, depending on the

T25 TORX

1. Verify Contents

2. Overview of NetServer Features

3. Obtain

Release History

4. Removing and Replacing the Covers

5. Install Additional Memory

6. Install All Accessory Boards

7. Replace Covers

8. Install the NetServer in the Rack

9. Install Additional Mass Storage Devices

10. Make External Connections

11. Configure the HP NetServer

HP NetServer Navigator CD-ROM

NetServer LH 4r Installation Road Map

Unpack and verify the contents of the shipping box against the Contents Checklist included with your HP NetServer. If anything is missing or

damaged, contact your reseller.

Verify Contents

Summary of content (6 pages)

PAGE 1
Printed in November 1998 Printed on recycled paper. 5967-6608 Hewlett-Packard Company Network Server Division P.O. Box 58059, Technical Marketing Santa Clara, CA 95052-8059 USA © Copyright 1998, Hewlett-Packard Company Hewlett-Packard makes no warranty of any kind with regard to this material, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose.
PAGE 2
Overview of NetServer Features NOTE Shelf 1 (Flexible Disk Drive) Power redundancy requires four power supply modules. No redundancy is available with three modules.
PAGE 3
4 Removing and Replacing the Covers If you are installing accessory cards or mass storage, remove cover 1. If you are installing memory, remove cover 3. To install some options, you will need a flat 1/4-inch screwdriver or a T15 TORX driver, depending on the accessory. WARNING 2. Loosen the thumbscrew at the front of the cover and pull the cover forward, using the handle on the cover, and then lift it off the chassis.
PAGE 4
6 Install All Accessory Boards NOTE Accessory Board Retainer For a list of boards HP has tested, see Help topic "Tested Parts List" on the HP NetServer Navigator CD-ROM. Release Tab 1. Remove cover 1 as described in panel 4, "Removing and Accessory Board Guide Replacing the Covers." 2. Read the documentation included with each accessory board. Follow any special instructions and installation recommendations. Some boards have preferred slot locations.
PAGE 5
9 Install Additional Mass Storage Devices This HP NetServer supports both hot-swap SCSI devices, installed in the hot-swap mass storage cage, and non-hot swap SCSI devices, installed in shelves 3 and 4 (located below the CD-ROM drive). Removing a Hot-Swap Disk Drive Module 1. Let the drive spin down completely before removing it (about 1 minute). 2. Press in on the locking latch at the end of the drive ejector handle and gently open the handle.
PAGE 6
Mouse 10 Keyboard Make External Connections AC Power Connector Make external connections, such as the monitor, keyboard, and mouse cables, UPS, and the AC power cord to the appropriate connectors on the rear of the chassis as instructed in the Rack Cabling Guide Reference for the HP NetServer LH 4r. Note that four power supplies are shown here. Monitor Rear View 11 AC Power Connector Configure the HP NetServer 1. Boot the HP Navigator CD-ROM: Turn on the monitor.