5525B/31/32 Line Matrix Printer User's Manual
Table Of Contents
- 1 Introduction
- 2 Setting Up the Printer
- 3 Operating the Printer
- 4 The Configuration Menus
- Configuration Overview
- CONFIG. CONTROL
- ACTIVE EMULATION
- EMULATION
- PCL-II Emulation
- LinePrinter Plus Emulations
- Optional Emulations
- PCL-II Emulation
- LinePrinter Plus Emulation
- P-Series Emulation
- Proprinter XL Emulation
- Epson FX Emulation
- IGP/PGL Submenu
- Features
- Configuring the Emulation with the Control Panel
- Define CR Code (Carriage Return)
- Define LF Code (Line Feed)
- Autowrap
- Select SFCC
- PI Slew Range
- CR Edit
- Select Font
- Select LPI
- Auto Uppercase
- Skip Command Prefix
- Power On IGP/PGL
- Extended Execute Copy
- UPC Descenders
- Compressed CPI
- Ignore Character
- IGP100 Compatbl.
- Optimized Ratio
- IGP/VGL Emulation
- MAINT / MISC
- HOST INTERFACE
- ETHERNET PARAMETERS
- PRINTER CONTROL
- DIAGNOSTICS
- RIBBONMINDER
- 5 Interfaces
- Overview
- Dataproducts Long Line Interface
- IEEE 1284 Parallel Interface
- RS-232 and RS-422 Serial Interfaces
- Host System Configuration
- Internal Ethernet Adapter Configuration
- Configuring the Internal Ethernet Adapter for TCP/IP
- Host Software
- Compiling Host Software
- Computer-aided Configuration with ezsetup or npconfig
- Configuration Through the Network with ARP
- Configuration Through the Network with RARP
- Configuration Through the Network with BOOTP
- Restoring Factory Defaults
- Host Configuration
- Direct Printing Without Spooler
- Printing Via the Spooler
- Custom Interface Scripts
- BSD UNIX
- System V UNIX
- npd Pseudo-device Interface
- Other TCP/IP Methods
- Configuring The Internal Ethernet Adapter For Novell
- Configuring the Internal Ethernet Adapter for Windows
- 6 Troubleshooting
- A Printer Specifications
- B Downloading Firmware
- C ASCII Character Set
- D Communication and Trademark Information
Chapter 6 Diagnosing Problems
204
PAP ILLGL ST* No Fatal firmware error on
controller board.
Contact your authorized service
representative.
1
PAP INCMPL ENER* No Fatal firmware error on
controller board.
Contact your authorized service
representative.
1
PAP INVLD CMD* No Fatal firmware error on
controller board.
Contact your authorized service
representative.
1
PAP INVLD PARM* No Fatal firmware error on
controller board.
Contact your authorized service
representative.
1
PAP NOT SCHED* No Fatal firmware error on
controller board.
Contact your authorized service
representative.
1
PAP NT AT SPEED* No Fatal firmware error on
controller board.
Contact your authorized service
representative.
1
PAP UNEXP INT* No Fatal firmware error on
controller board.
Contact your authorized service
representative.
1
PARITY ERROR Yes Parity error
(serial interface)
Check your serial host interface
parameter settings; if necessary,
adjust them so that they match
the settings of the attached host.
POWER SUPPLY HOT Yes Power supply sensors report
high temperatures.
Check printer environment. If hot
or dusty, relocate printer. Contact
your authorized service
representative if this occurs
frequently.
1
PROTECTED INSTR* No Fatal firmware error on
controller board.
Contact your authorized service
representative.
1
PLAT INV PARM* No Fatal firmware error on
controller board.
Contact your authorized service
representative.
1
PLAT INV CMD* No Fatal firmware error on
controller board.
Contact your authorized service
representative.
1
PLAT INV STATE* No Fatal firmware error on
controller board.
Contact your authorized service
representative.
1
Table 15. LCD Message Troubleshooting Table (continued)