5525B/31/32 Line Matrix Printer User's Manual
Table Of Contents
- 1 Introduction
- 2 Setting Up the Printer
- 3 Operating the Printer
- 4 The Configuration Menus
- Configuration Overview
- CONFIG. CONTROL
- ACTIVE EMULATION
- EMULATION
- PCL-II Emulation
- LinePrinter Plus Emulations
- Optional Emulations
- PCL-II Emulation
- LinePrinter Plus Emulation
- P-Series Emulation
- Proprinter XL Emulation
- Epson FX Emulation
- IGP/PGL Submenu
- Features
- Configuring the Emulation with the Control Panel
- Define CR Code (Carriage Return)
- Define LF Code (Line Feed)
- Autowrap
- Select SFCC
- PI Slew Range
- CR Edit
- Select Font
- Select LPI
- Auto Uppercase
- Skip Command Prefix
- Power On IGP/PGL
- Extended Execute Copy
- UPC Descenders
- Compressed CPI
- Ignore Character
- IGP100 Compatbl.
- Optimized Ratio
- IGP/VGL Emulation
- MAINT / MISC
- HOST INTERFACE
- ETHERNET PARAMETERS
- PRINTER CONTROL
- DIAGNOSTICS
- RIBBONMINDER
- 5 Interfaces
- Overview
- Dataproducts Long Line Interface
- IEEE 1284 Parallel Interface
- RS-232 and RS-422 Serial Interfaces
- Host System Configuration
- Internal Ethernet Adapter Configuration
- Configuring the Internal Ethernet Adapter for TCP/IP
- Host Software
- Compiling Host Software
- Computer-aided Configuration with ezsetup or npconfig
- Configuration Through the Network with ARP
- Configuration Through the Network with RARP
- Configuration Through the Network with BOOTP
- Restoring Factory Defaults
- Host Configuration
- Direct Printing Without Spooler
- Printing Via the Spooler
- Custom Interface Scripts
- BSD UNIX
- System V UNIX
- npd Pseudo-device Interface
- Other TCP/IP Methods
- Configuring The Internal Ethernet Adapter For Novell
- Configuring the Internal Ethernet Adapter for Windows
- 6 Troubleshooting
- A Printer Specifications
- B Downloading Firmware
- C ASCII Character Set
- D Communication and Trademark Information
Index
228
ERROR DRAM AT ADDRESS
XXXXXXXX, 216
ERROR EC PROGRAM NOT VALID, 216
ERROR EC STOPPED AT STATE XXXX,
216
ERROR FLASH NOT DETECTED, 217
Error Handling, 108
Error markers, 108
Error messages See Fault messages, 200
ERROR NO DRAM DETECTED, 216
ERROR NVRAM FAILURE, 217
ERROR PROGRAM NEEDS MORE
DRAM, 217
ERROR PROGRAM NEEDS MORE
FLASH, 217
ERROR PROGRAM NOT COMPATIBLE,
217
ERROR PROGRAM NOT VALID, 217
ERROR SECURITY PAL NOT
DETECTED, 217
ERROR SHORT AT ADDRESS XXXX, 217
ERROR WRITING TO FLASH, 216, 217
ERROR WRONG CHECKSUM, 218
ETHERNET PARAMETERS Menu, 122
Ethernet Submenu, 121
EVFU Select, 86
EXHAUST FAN FLT message, 202
Extended Execute Copy, 99
ezsetup
installation program
setting up, 147
F
Fault Action, 130
Fault messages, 200
021 RECEIVE BUFFER OVERRUN
VERIFY CONFIGURATION,
201
15V PWR FAIL *, 201
23.5V PWR FAIL *, 201
48V PWR FAIL *, 201
8.5V PWR FAIL *, 201
A TO D OVERUN *, 201
ACCESS NULL PTR *, 201
BUFFER OVERFLOW, 201
CAUTION PPM HAS REMOTE
CONTROL, 201
CLEAR PAPER JAM, 201
CLOSE PLATEN, 201
COIL HOT, 202
CTL VOLT FAIL *, 202
DRVR CIR BAD *, 202
EXHAUST FAN FLT, 202
FIRMWARE ERROR, 202
FRAMING ERROR, 202
HAM. COIL OPEN *, 202
HAMMER COIL BAD, ###, 202
HB NOT INSTALLD *, 203
ILL EXT BUS ACC *, 203
ILL INST ACCSS *, 203
ILLGL OPR ACCSS *, 203
INTAKE FAN FAULT, 203
LO DRV. SHORT *, 203
LOAD PAPER, 203