5525B/31/32 Line Matrix Printer User's Manual
Table Of Contents
- 1 Introduction
- 2 Setting Up the Printer
- 3 Operating the Printer
- 4 The Configuration Menus
- Configuration Overview
- CONFIG. CONTROL
- ACTIVE EMULATION
- EMULATION
- PCL-II Emulation
- LinePrinter Plus Emulations
- Optional Emulations
- PCL-II Emulation
- LinePrinter Plus Emulation
- P-Series Emulation
- Proprinter XL Emulation
- Epson FX Emulation
- IGP/PGL Submenu
- Features
- Configuring the Emulation with the Control Panel
- Define CR Code (Carriage Return)
- Define LF Code (Line Feed)
- Autowrap
- Select SFCC
- PI Slew Range
- CR Edit
- Select Font
- Select LPI
- Auto Uppercase
- Skip Command Prefix
- Power On IGP/PGL
- Extended Execute Copy
- UPC Descenders
- Compressed CPI
- Ignore Character
- IGP100 Compatbl.
- Optimized Ratio
- IGP/VGL Emulation
- MAINT / MISC
- HOST INTERFACE
- ETHERNET PARAMETERS
- PRINTER CONTROL
- DIAGNOSTICS
- RIBBONMINDER
- 5 Interfaces
- Overview
- Dataproducts Long Line Interface
- IEEE 1284 Parallel Interface
- RS-232 and RS-422 Serial Interfaces
- Host System Configuration
- Internal Ethernet Adapter Configuration
- Configuring the Internal Ethernet Adapter for TCP/IP
- Host Software
- Compiling Host Software
- Computer-aided Configuration with ezsetup or npconfig
- Configuration Through the Network with ARP
- Configuration Through the Network with RARP
- Configuration Through the Network with BOOTP
- Restoring Factory Defaults
- Host Configuration
- Direct Printing Without Spooler
- Printing Via the Spooler
- Custom Interface Scripts
- BSD UNIX
- System V UNIX
- npd Pseudo-device Interface
- Other TCP/IP Methods
- Configuring The Internal Ethernet Adapter For Novell
- Configuring the Internal Ethernet Adapter for Windows
- 6 Troubleshooting
- A Printer Specifications
- B Downloading Firmware
- C ASCII Character Set
- D Communication and Trademark Information
Index
229
ONLINE 8344 FAILED, 203
PAP BAD TABLE *, 203
PAP BSY TOO LNG *, 203
PAP FIFO OVERFL *, 203
PAP FIFO UNDRFL *, 203
PAP ILLGL ST *, 204
PAP INCMPL ENER *, 204
PAP INVLD CMD *, 204
PAP INVLD PARM *, 204
PAP NOT SCHED *, 204
PAP NT AT SPEED *, 204
PAP UNEXP INT *, 204
PARITY ERROR, 204
PLAT INV CMD *, 204
PLAT INV PARM *, 204
PLAT INV STATE *, 204
POWER SAVER MODE, 205
POWERSUPPLY HOT *, 204
PRINTER HOT *, 205
PROTECTED INSTR *, 204
PWRSUPP VOLT *, 205
RIB INVLD CMD *, 205
RIB INVLD STAT *, 205
RIBBON DRIVE, 205
RIBBON INK OUT, CHANGE
RIBBON, 205
SECURITY VIOLATION, 205
SHUTL INV CMD *, 205
SHUTL INV PARM *, 205
SHUTTLE JAM, 205
SOFTWARE ERROR *, 206
STACK OVERFLOW *, 206
FF key, 43
FF Valid at TOF, 88
FIRMWARE ERROR message, 202
Flash memory, loading, 213
Flash messages
CLEARING PROGRAM FROM
FLASH, 216, 218
DIAGNOSTICS PASSED, 216
ERROR DC PROGRAM NOT VALID,
216
ERROR DRAM AT ADDRESS
XXXXXXXX, 216
ERROR EC PROGRAM NOT VALID,
216
ERROR EC STOPPED AT STATE
XXXX, 216
ERROR FLASH NOT DETECTED,
217
ERROR NO DRAM DETECTED, 216
ERROR NVRAM FAILURE, 217
ERROR PROGRAM NEEDS MORE
DRAM, 217
ERROR PROGRAM NEEDS MORE
FLASH, 217
ERROR PROGRAM NOT
COMPATIBLE, 217
ERROR PROGRAM NOT VALID, 217
ERROR SECURITY PAL NOT
DETECTED, 217
ERROR SHORT AT ADDRESS XXXX,
217
ERROR WRITING TO FLASH, 216,