5525B/31/32 Line Matrix Printer User's Manual
Table Of Contents
- 1 Introduction
- 2 Setting Up the Printer
- 3 Operating the Printer
- 4 The Configuration Menus
- Configuration Overview
- CONFIG. CONTROL
- ACTIVE EMULATION
- EMULATION
- PCL-II Emulation
- LinePrinter Plus Emulations
- Optional Emulations
- PCL-II Emulation
- LinePrinter Plus Emulation
- P-Series Emulation
- Proprinter XL Emulation
- Epson FX Emulation
- IGP/PGL Submenu
- Features
- Configuring the Emulation with the Control Panel
- Define CR Code (Carriage Return)
- Define LF Code (Line Feed)
- Autowrap
- Select SFCC
- PI Slew Range
- CR Edit
- Select Font
- Select LPI
- Auto Uppercase
- Skip Command Prefix
- Power On IGP/PGL
- Extended Execute Copy
- UPC Descenders
- Compressed CPI
- Ignore Character
- IGP100 Compatbl.
- Optimized Ratio
- IGP/VGL Emulation
- MAINT / MISC
- HOST INTERFACE
- ETHERNET PARAMETERS
- PRINTER CONTROL
- DIAGNOSTICS
- RIBBONMINDER
- 5 Interfaces
- Overview
- Dataproducts Long Line Interface
- IEEE 1284 Parallel Interface
- RS-232 and RS-422 Serial Interfaces
- Host System Configuration
- Internal Ethernet Adapter Configuration
- Configuring the Internal Ethernet Adapter for TCP/IP
- Host Software
- Compiling Host Software
- Computer-aided Configuration with ezsetup or npconfig
- Configuration Through the Network with ARP
- Configuration Through the Network with RARP
- Configuration Through the Network with BOOTP
- Restoring Factory Defaults
- Host Configuration
- Direct Printing Without Spooler
- Printing Via the Spooler
- Custom Interface Scripts
- BSD UNIX
- System V UNIX
- npd Pseudo-device Interface
- Other TCP/IP Methods
- Configuring The Internal Ethernet Adapter For Novell
- Configuring the Internal Ethernet Adapter for Windows
- 6 Troubleshooting
- A Printer Specifications
- B Downloading Firmware
- C ASCII Character Set
- D Communication and Trademark Information
Index
233
specifications, 207
temperature requirements, 16
PRINTER CONTROL Menu, 123
Printer Dimensions
Setting Up the Printer, 17
PRINTER HOT * message, 205
Printer Protocol, 80
Printer Select, 91
Printer Tests, 125
printing conventions
manual, 12
Printouts
hex code, 198
Proprinter XL Emulation, 87
Protect Configs, 72
PROTECTED INSTR * message, 204
Protocol, 14
P-Series Emulation, 83
PSERVER Bootup See Configuring the
Internal Ethernet Adapter, 174
PSERVER Setup See Configuring the
Internal Ethernet Adapter, 175
PTX Linefeed, 78
PWRSUPP VOLT * message, 205
R
Ready signal
Dataproducts Long Lines interface,
133
Received Data (RD) signal
RS-232 serial interface, 141
Received data (RD) signal
RS-422 serial interface, 141
Reloading Paper, 47
Replacing the Ribbon, 57
Request to Send, 119
Request To Send (RTS) signal
RS-232 serial interface, 141
Requirements
printer, power, 15
RESETTING . . . / PLEASE WAIT, 218
Resistors
configuration, 138
installation, 139
removal, 139
Response Polarity, 115
RESTORING BOOT CODE, 218
RIB INVLD CMD * message, 205
RIB INVLD STATE * message, 205
Ribbon
installing, 32
specifications, 207
Ribbon Action, 129
Ribbon Adjust, 130
RIBBON DRIVE message, 205
RIBBON INK OUT, CHANGE RIBBON,
205
Ribbon Size, 130
RibbonMinder Fault, 130
RIBBONMINDER Menu, 128
Rot. Char Size, 107
RPRINTER Bootup See Configuring the
Internal Ethernet Adapter, 174
RPRINTER Setup See Configuring the
Internal Ethernet Adapter, 177