Debug Manual
Table Of Contents
- What’s New in This Manual
- About This Manual
- 1 Introduction
- Execution Modes on TNS/R Systems
- What User Access Is Required for Debugging
- How to Make a Process Enter Debug
- How to Select Debug as the Debugger
- Why a Process Enters Debug
- How to Determine Process State on a Trap or Signal
- Ending a Debug Session
- What Appears in the Debug Header Message
- How to Use Debug
- How Debug Breakpoints Work
- 2 Using Debug on TNS/R Processors
- 3 Debug Command Overview
- 4 Debug Commands
- Command Summary
- A Command
- AMAP Command
- B Command
- BASE Command
- BM Command
- C Command
- CM Command
- D Command
- DJ Command
- DN Command
- EX[IT] Command
- F[ILES] Command
- FC Command
- FN Command
- FNL Command
- FREEZE Command
- HALT Command
- H[ELP] Command
- I Command
- IH Command (TNS/R Native and OSS Processes)
- INSPECT Command
- LMAP Command
- M Command
- MH Command (TNS/R Native and OSS Processes)
- P[AUSE] Command
- PMAP Command (Accelerated Programs)
- PRV Command
- R Command
- S[TOP] Command
- T Command
- V Command
- VQ Command
- VQA Command
- = Command
- ? Command
- A Error Messages
- B ASCII Character Set
- C Command Syntax Summary
- Register Syntax
- Expression Syntax
- Address Syntax
- A Command
- AMAP Command
- B Command
- BASE Command
- BM Command
- C Command
- CM Command
- D Command
- DJ Command
- DN Command
- EX[IT] Command
- F[ILES] Command
- FC Command
- FN Command
- FNL Command
- FREEZE Command
- HALT Command
- H[ELP] Command
- I Command
- IH Command
- INSPECT Command
- LMAP Command
- M Command
- MH Command
- Output-Device Syntax
- P[AUSE] Command
- PMAP Command
- PRV Command
- R Command
- S[TOP] Command
- T Command
- V Command
- VQ Command
- VQA Command
- = Command
- ? Command
- D Session Boundaries
- E Correspondence Between Debug and Inspect Commands
- F Sample Debug Sessions
- Glossary
- Index
Debug Commands
Debug Manual—421921-003
4-21
Display Breakpoints
Example
For conditional breakpoint examples, see Appendix F, Sample Debug Sessions.
Format of the Trace Breakpoint Display
For a trace breakpoint (code or memory-access), displays the trace information under
the normal breakpoint information. The trace parameter is displayed in one of these
two forms:
The 32-bit display form:
The 16-bit display form:
index is an offset from the base address. This can be used with 16-bit
addresses only.
mask is an expression as defined under Set Conditional Code
Breakpoint on page 4-11.
constant is an expression as defined under Set Conditional Code
Breakpoint on page 4-11..
{register | start-address } ? count
register is one of the TNS/R registers.
start-address is a 32-bit address.
? is the trace indicator.
count is the number of 16-bit words to be displayed. The value of
count can be either 16 bits or 32 bits. If it is 32 bits, only the
lower 16 bits are used for the number of 16-bit words to display.
{ register | start-address }[ { I } [index] ] ? count
{ IX }
{ GX }
register is one of the TNS/R stack registers (R0 through R7) as
described under Register Syntax on page 3-7.
start-address is a 16-bit address or a 32-bit address.
I, IX, GX is integer indirect, integer extended indirect, and integer
indirect global. These indirect types can be used with 16-bit
addresses only.