G06.28 Software Installation and Upgrade Guide Abstract This manual provides detailed procedures for upgrading an HP NonStop™ S-series server to the G06.28 release version update (RVU) from any G06.06 or later RVU. Product Version N.A. Supported Release Version Updates (RVUs) This publication supports the G06.28 RVU only.
Document History Part Number Product Version 541688-001 N.A.
G06.28 Software Installation and Upgrade Guide Glossary Index What’s New in This Manual xiii Manual Information xiii New and Changed Information Figures Tables xiii About This Manual xv Who Should Use This Guide xv What This Guide Does Not Cover xv How This Guide Relates to Other Manuals Notation Conventions xvii xvi 1. Overview of Installing G06.
Contents 1. Overview of Installing G06.28 Falling Back to the Previous RVU (continued) DSM/SCM Client and Server Compatibility 1-25 Running ZPHIRNM Again Before a System Load 1-25 Resecuring and Licensing Requirements 1-26 NonStop TCP/IP FTP 1-26 Do Not Move or Relicense Pathway Files 1-26 Secure SCF Product Modules 1-26 Resecure Visual Inspect 1-27 G06.28 Installation and Fallback Alerts for Products 1-27 4619 Disk Drives 1-28 6780 ServerNet Switch (G06.21) 1-28 Backup and Restore 2 (BR2) (G06.
2. G06.28 Upgrade Checklists Contents G06.28 Installation and Fallback Alerts for Products X25AM 1-47 ServerNet Cluster 1-48 SMF 1-48 (continued) Part I. Upgrade Tasks 2. G06.28 Upgrade Checklists G06.28 Upgrade Checklist 2-1 G06.28 Required Information Checklist 2-4 3. Installing SPRs Before Upgrading to the G06.
5. Installing the G06.28 RVU Contents Verify System Operations (continued) Check Disk Subsystem Status 4-13 Check the Swap File Configuration 4-14 Check the Status of the Spooler Collector 4-15 Check the Tape Drive Status 4-16 Check Products With Possible Regressions 4-16 Record the Current SYSnn 4-17 Back Up Important Files 4-17 5. Installing the G06.
8.
10. Running ZPHIRNM (continued) Contents 10. Running ZPHIRNM (continued) Drain the Spooler 10-3 Back Up the Spooler Control Files 10-4 ZPHIRNM 10-4 Using ZPHIRNM PREVIEW Mode 10-4 Steps for Running ZPHIRNM 10-5 Verify That ZPHIRNM Ran Successfully 10-9 11. Loading the G06.
12. Resuming Normal Operations (continued) Contents 12.
16.
Contents B.
Contents C. Updating SWAN Concentrator CLIP Firmware Install the DSM/SCM Client From ZDSMSCM (continued) Create an ERD or ASR Disk B-22 C.
Tables (continued) Contents Tables (continued) Table 1-3. Table 1-4. Table 1-5. Table 1-6. Table 1-7. Table 1-8. Table 1-9. Table 2-1. Table 2-2. Table 3-1. Table 3-2. Table 3-3. Table 3-4. Table 3-5. Table 4-1. Table 7-1. Table 8-1. Table B-1. G06.28 Updateable Firmware for ServerNet WAN (SWAN and SWAN 2) Concentrators 1-15 G06.28 Updateable Firmware for the NonStop ServerNet Switch 1-16 G06.28 IOAM Firmware 1-16 Tasks and Tools for Installing the G06.
Contents G06.
What’s New in This Manual Manual Information G06.28 Software Installation and Upgrade Guide Abstract This manual provides detailed procedures for upgrading an HP NonStop™ S-series server to the G06.28 release version update (RVU) from any G06.06 or later RVU. Product Version N.A. Supported Release Version Updates (RVUs) This publication supports the G06.28 RVU only. Part Number Published 541688-001 February 2006 Document History Part Number Product Version Published 541688-001 N.A.
What’s New in This Manual New and Changed Information G06.
About This Manual This guide describes: • • Upgrading a single NonStop S-series server to the G06.28 release version update (RVU) of the HP NonStop operating system from any G06.06 or later G-series RVU, including installing DSM/SCM client software. Falling back from the G06.28 RVU to a previous (G06.06 or later) G-series RVU. If you are migrating from an RVU prior to G06.06, contact your service provider trained by HP.
About This Manual • • How This Guide Relates to Other Manuals Installing, configuring, and migrating to HP NonStop SQL/MX. The SQL/MX Installation and Management Guide for SQL/MX Release 2.0 describes step-bystep instructions for installing NonStop SQL/MX for Release 2.0, including fallback procedures. Installing and configuring the I/O adapter module (IOAM) enclosure and its components. See your HP service provider.
Notation Conventions About This Manual • • • The NonStop S-Series Planning and Configuration Guide provides information for planning and configuring the installation of a NonStop S-series server. The NonStop S-Series Hardware Installation and FastPath Guide provides detailed instructions and checklists for installing NonStop S-series servers. The SQL/MX Installation and Management Guide for NonStop SQL/MX Release 2.0 describes step-by-step instructions for installing NonStop SQL/MX for Release 2.0.
General Syntax Notation About This Manual [ ] Brackets. Brackets enclose optional syntax items. For example: TERM [\system-name.]$terminal-name INT[ERRUPTS] A group of items enclosed in brackets is a list from which you can choose one item or none. The items in the list may be arranged either vertically, with aligned brackets on each side of the list, or horizontally, enclosed in a pair of brackets and separated by vertical lines. For example: FC [ [ [ K [ num ] -num ] text ] X | D ] address { } Braces.
Notation for Messages About This Manual Item Spacing. Spaces shown between items are required unless one of the items is a punctuation symbol such as a parenthesis or a comma. For example: CALL STEPMOM ( process-id ) ; If there is no space between two items, spaces are not permitted. In the following example, there are no spaces permitted between the period and any other items: $process-name.#su-name Line Spacing.
Notation for Messages About This Manual be arranged either vertically, with aligned brackets on each side of the list, or horizontally, enclosed in a pair of brackets and separated by vertical lines. For example: proc-name trapped [ in SQL | in SQL file system ] { } Braces. A group of items enclosed in braces is a list of all possible items that can be displayed, of which one is actually displayed.
1 Overview of Installing G06.28 This section introduces the tools and requirements for: • • Upgrading a single NonStop S-series server to the G06.28 RVU from a G06.06 or later G-series RVU Falling back from G06.28 to a previous (G06.06 or later) G-series RVU Disk Space Requirements The maximum site update tape (SUT) with all standard products, plus all optional products available to customers, contains approximately 2 or 3 gigabytes (GB) of data, depending on optional products.
Overview of Installing G06.28 TSM and OSM Client Applications You can have both the TSM client and the OSM client-based components on your system consoles. However, to avoid duplicate dial-outs, use either the OSM Notification Director (ND) or TSM Notification Director, but not both. HP Systems Insight Manager (SIM) HP Systems Insight Manager (SIM) can now be used in conjunction with OSM software to help manage your NonStop servers.
Overview of Installing G06.28 • • • • OSM Client-Based Components (S7X-SWV1/HNSCSWV1, Update 7 and Update 8) The OSM Low-Level Link has a direct link to the SP tool. (Select Advanced Service Processor Tool from the Tools menu). The OSM Low-Level Link does not have a direct link to the TSM Event Viewer (Instead, select Start > Programs > Compaq TSM > TSM Event Viewer.) The Action Status Summary is not available in the OSM Low-Level Link. The Single SP Firmware update is also not available on the menu bar.
Overview of Installing G06.28 OSM Client-Based Components (S7X-SWV1/HNSCSWV1, Update 7 and Update 8) Figure 1-1. OSM Low-Level Link Application VST003.vsd • OSM Notification Director. Installer S7X-SWV1/HNSC-SWV1, Update 7, includes the T6032AAO SPR; T6032AAP will be available on Update 8. Starting with Installer S7X-SWV1/HNSC-SWV1, Update 7, installing OSM Notification Director also installs the RemoteProxy Service.
Overview of Installing G06.28 • Server Software Requirements OSM Console Tools. Installer S7X-SWV1/HNSC-SWV1, Update 7, includes SPR T6034AAJ; T6034AAK will be available on Update. OSM Console Tools consists of: ° Windows Start menu shortcuts for launching the OSM Service Connection and OSM Event Viewer. (These applications are part of the OSM server-based component (T0682), and are accessed through Internet Explorer browser sessions from your system console).
Overview of Installing G06.28 • • NonStop SQL/MX Install the desired OSM server SPRs (see Caution above) if you decide that you want to use OSM. The latest OSM SPR, T0682AAI, is available on the G06.28 SUT and on Scout. For new features, see the Interactive Upgrade Guide 2. For installation and configuration information, see the OSM Migration Guide. You must use OSM (instead of TSM) to: ° Manage and configure ServerNet Clusters using layered topology with ServerNet Switch model 6780.
Overview of Installing G06.28 SWID DSM/SCM. The DSM/SCM client and server product version enables you to manage OSS files and is compatible with systems running H-series RVUs. Note. All OSS SUT-based products with pax files must have the A7CINFO file in their distributed subvolumes (DSVs) to be installed by DSM/SCM. Check the appropriate product softdocs and the Interactive Upgrade Guide 2 to ensure that DSM/SCM installation is possible.
Overview of Installing G06.28 Installing Required or Recommended SPRs Before Installing a New RVU HP recommends that the target systems be upgraded to at least the T6031ABR version of DSM/SCM before the host system is upgraded to this SPR. Installing Required or Recommended SPRs Before Installing a New RVU Before installing G06.28, install required or recommended SPRs.
Overview of Installing G06.28 • • Managing Microcode and Firmware Rename the files that currently have actual file names to fabricated names. These files become obsolete when the new files are renamed. Rename the new files, which have fabricated names, to their actual names.
Overview of Installing G06.28 Updating Firmware Bootstrap Microcode Update Requirements for the G06.28 RVU The disk and tape bootstrap programs (T8494) are unchanged in G06.28. A new disk bootstrap program (T8494AAA) became available in G06.06. Revive your mirrored disk as soon as possible after performing a system load.
Overview of Installing G06.28 Updating Firmware NonStop Cluster Switch Firmware To monitor and manage a ServerNet Cluster product configured with 6780 switches, you can use either the OSM Service Connection or SCF commands. See the ServerNet Cluster 6780 Operations Guide for more information. For information on required software, installation, migration, and fallback procedures, see the ServerNet Cluster 6780 Planning and Installation Guide.
Overview of Installing G06.28 Updating Firmware Firmware Updates Using OSM or TSM Use the TSM Service Application or the OSM Service Connection (if OSM is already installed) to update service processor (SP) firmware and processor boot code before system load and to update SCSI boot code (pre-G06.08), SWAN concentrator CLIP, and other firmware after system load. Adapter firmware is generally automatically downloaded when a ServerNet adapter is started during system load.
Updating Firmware Overview of Installing G06.28 Table 1-1. G06.
Updating Firmware Overview of Installing G06.28 Table 1-2. G06.
Updating Firmware Overview of Installing G06.28 Table 1-2. G06.
Updating Firmware Overview of Installing G06.28 Table 1-4. G06.
Overview of Installing G06.28 Updating Firmware Updating Firmware Before System Load Caution. Before upgrading boot millicode using the online update function to T7892ABD, you must have the G06.24 or later version of either the TSM server (T7945ABN) or all OSM serverbased SPRs (along with their prerequisites) configured and running. Otherwise, a processor halt will result. Use the TSM Service Application to update SP firmware and processor boot code before you perform a system load with the new RVU.
Overview of Installing G06.28 Investigating a New RVU Investigating a New RVU Several resources are available to help you plan for installing a new RVU: • • • • • The Release Version Update Compendium provides highlights of the new products and features for each G-series RVU. It also discusses the effect these changes have on installation and configuration, operations and management, data files, applications, and networks.
Installing a New RVU Overview of Installing G06.28 Table 1-6. Tasks and Tools for Installing the G06.28 RVU (page 1 of 2) To Perform This Task... Use This Tool... Documented in... 1. Install the T6031G02 product version of DSM/SCM and fallback/interoperability SPRs. HP recommends that you install the T6031G02 SPR on the host and on the client. You must also install the SWID product T9298G02 if you are installing the T6031ABR SPR available on the SUT.
Upgrading NonStop S-Series Servers Overview of Installing G06.28 Table 1-6. Tasks and Tools for Installing the G06.28 RVU (page 2 of 2) To Perform This Task... Use This Tool... Documented in... 10. Activate the new software revision. DSM/SCM ZPHIRNM program Section 10, Running ZPHIRNM 11. Halt the processors. TSM Low-Level Link Application or OSM LowLevel Link Halt the Processors on page 11-2 12. Load the new operating system from disk into the memory of one processor (system load).
Overview of Installing G06.28 Installing an IOAM Enclosure and Other Components which means that a query performed on the system returns NSR-G if the PMF is a model 1951 PMF CRU (S70000). After you change the CONFTEXT file, you must perform all required DSM/SCM requests to create a new SYSnn, including the new processor type. Perform a system load of the new SYSnn after the new hardware is installed. Caution. Never load the new SYSnn that contains the new processor type into your current processors.
Overview of Installing G06.28 • Installing an IOAM Enclosure and Other Components You must isolate SWAN adapters on your system before you install an IOAM enclosure. For more information, contact your service provider. To connect an IOAM enclosure to a NonStop S-series system in a group other than group 01, you must ensure that: • • The Maintenance Entity firmware version on the ServerNet switch board is at least T2805AAD. The SP firmware version on the NonStop S-series system is T1089ABR.
Falling Back to the Previous RVU Overview of Installing G06.28 Falling Back to the Previous RVU If you encounter a problem that cannot be resolved while running G06.28, you can fall back to a previous G-series RVU, provided you have already installed the appropriate fallback SPRs for your system. Note. In most instances, it is not necessary to return SP firmware or SCSI boot code back to the previous firmware versions when falling back to an earlier RVU. Check with Scout for SPR backward compatibility.
Overview of Installing G06.28 Using DSM/SCM FALLBACK and CLEANOSS Macros Using DSM/SCM FALLBACK and CLEANOSS Macros If you did not migrate to G06.25 and install DSM/SCM T6031D46^ABK SPR, you must run the FALLBACK macro even if you have installed a T6031D46 SPR. The interactive macro must be run by the DSM/SCM owner or by the super ID (255,255). The FALLBACK macro reverts the DSM/SCM Host or Target, or both, database back to a pre-T6031D46^ABK, ABN, or ABP state.
Overview of Installing G06.28 DSM/SCM Client and Server Compatibility Notes on the CLEANOSS Macro If you fall back and then migrate to G06.28 RVU, DSM/SCM might notify you during the Apply that the CLEANOSS macro must be run. The current OSS environment is being managed by a logical target other than the one trying to manage OSS files with the current DSM/SCM Build/Apply. You must cancel the Apply, and run the CLEANOSS macro.
Overview of Installing G06.28 Resecuring and Licensing Requirements Resecuring and Licensing Requirements Important resecuring and licensing requirements follow. NonStop TCP/IP FTP Beginning with G06.08, all files in the CSSnn subvolume must be secured “NUNU” to work properly. For details, see the T6022AAG or later softdoc.
Overview of Installing G06.28 Resecure Visual Inspect Resecure Visual Inspect Visual Inspect consists of a server component (T9756), a standard product distributed on all SUTs, and a client component (T7877), which is an independent product (IP). If necessary, resecure the server INSPECT files (INSPBRKR, INSPRULE, INSPSVR, and INSPSMSG) in the SYSnn subvolumes with network read and execute access, NxNx. For other migration issues, see Visual Inspect on page 1-47. G06.
Overview of Installing G06.28 • • • • • • • 4619 Disk Drives NonStop TCP/IPv6 on page 1-43 TMF on page 1-44 TNOS Server and TNOS Utility on page 1-46 Visual Inspect on page 1-47 WAN Wizard Pro on page 1-47 X25AM on page 1-47 Visual Inspect on page 1-47 4619 Disk Drives You can install the 4619 disk drive in the same system enclosure as disk drives of different model numbers. However, disk drives in a mirrored volume must always be the same model number, even if they are of the same capacity.
Overview of Installing G06.28 C++ C++ The G06.20 RVU introduced a fully ANSI 98-compliant C++ run-time library, designated as the C++ v3 run-time library (v3 RTL). Starting in G06.20, you have a choice of three different C++ language dialects: v1, v2, and v3. The default compiler dialect setting is changed from v1 to v3. The build file for any product that invokes a TNS/R native C++ must be examined and changed according to certain rules that are documented in the Interactive Upgrade Guide 2.
Overview of Installing G06.28 GESA If you are planning on using the new TMF format 2 audit trail format, migration issues might apply for DP2. The T9053G11 PVU provides support for TMF large audit trails and two new disk attributes for REVIVE. See the T9053G11 softdoc. GESA Any Gigabit Ethernet ServerNet adapters (GESAs) installed while migrating to G06.28 must be removed from the system during any fallback to an RVU prior to G06.16.
Overview of Installing G06.28 OSM Configuration and Fallback OSM Configuration and Fallback Note that if you are installing and using OSM, HP recommends that the NSK CRE/RTL (T1269) product be installed on the system, as opposed to the Native CRE/RTL (T8431), which is the default. For migration considerations for T1269, see S02001. For more information on configuring OSM, see S03133B. Caution. You cannot simultaneously use both heap managers (T8431 and T1269) on the same system.
Overview of Installing G06.28 • Beginning with the G06.23 RVU, you can use SCF to configure an OSS process as a persistent process under the persistence manager ($ZKRN). These SPRs (or later) are required to support SCF: ° ° ° ° ° ° ° • • OSS T1084G06^AAJ T1085G06^AAN T6586G07^AAZ T5800G06^AAR T9082G02 ^ADA T8624G10 ^AAN T8397G00 ^AAB For more information about the new attribute and considerations for its use, see the SCF Reference Manual for the Kernel Subsystem. Beginning with the G06.
Overview of Installing G06.28 OSS OSS and DSM/SCM (T6031D46 and T6031G02 PVUs) Starting with the G06.18 RVU, all OSS SUT-based products with pax files must have the A7CINFO file in their DSVs to be installed by DSM/SCM. Check the Interactive Upgrade Guide 2 or the softdoc corresponding to the OSS products to ensure that the A7CINFO file is present. If the OSS product is released without the A7CINFO file, you can still install the product by using PINSTALL or COPYOSS.
Overview of Installing G06.28 NonStop SQL/MP OSS EasySetup (T0585) The OSS EasySetup product (T0585) is available for automated setup, as described in the Open System Services Installation Guide. OSS EasySetup is a series of TACL scripts that assist a site when configuring and installing a minimal OSS subsystem for the first time or when starting, stopping, or removing an OSS subsystem. The product NULL (T6025) is still included on each SUT. Starting with G06.
Overview of Installing G06.28 NonStop SQL/MX Release 2.1.1 Migration Considerations for NonStop SQL/MX Release 2.1.1 Migration Notes for NonStop SQL/MX Release 2.1.1 Metadata tables created and used by NonStop SQL/MX Release 2.0 and later releases are different from those metadata tables used on prior NonStop SQL/MX releases, and the tables are very different from those used by NonStop SQL/MP. You must be on at least Release 1.8 to migrate to NonStop SQL/MX Release 2.1.1. Releases 2.1, 2.0, and 1.
NonStop SQL/MX Release 2.1.1 Overview of Installing G06.28 System: \MOLE *WARNING* *WARNING* PID: (0, 72) 8-Apr-2004 18:06:57 SQL Catalog will not be updated when SQL labels are deleted. Extents are lost when file/table labels are deleted. Note. When using DIRCHECK: • • • You must be the super ID (255,255). The DIRCHECK DELETE command deletes any internal labels associated with a specified file. Because of this, DIRCHECK indicates that multiple labels have been deleted after you delete one file.
NonStop SQL/MX Release 2.1.1 Overview of Installing G06.28 You install NonStop SQL/MX after performing a system load of the new RVU and performing other post-installation steps. (See Section 12, Resuming Normal Operations.) For more information about installing SQL/MX: For This Information: See: Summary of new SQL/MX features and characteristics Release 2.1.
Processor Multifunction (PMF) CRUs Overview of Installing G06.28 Processor Multifunction (PMF) CRUs If you upgrade to NonStop PMF CRUs while installing G06.28 and have to return to an RVU prior to G06.28, review the Interactive Upgrade Guide 2, the NonStop S-Series Central Office Server Installation and Service Guide, and Table 1-9 to see if you have to remove PMF CRUs. Table 1-9. Upgrading to NonStop S-Series CRUs and Falling Back (page 1 of 2) NonStop PMF CRU Introduced in this RVU S7400 G06.
Safeguard Overview of Installing G06.28 Table 1-9. Upgrading to NonStop S-Series CRUs and Falling Back (page 2 of 2) NonStop PMF CRU Introduced in this RVU S78000 G06.24 S78000 CRUs must be removed. These PMF CRUs are supported for G06.16 and later RVUs only. See the Interactive Upgrade Guide 2 for details. S78000SE G06.25 S78000 CRUs must be removed. These PMF CRUs are supported for G06.16 and later RVUs only. See the Interactive Upgrade Guide 2 for details. S88000 G06.
Overview of Installing G06.28 Spooler Spooler If your current product version of spooler is T9101D41^ADM or later, you do not need to restore copies of both the control file and the collector data files if you must back out of the new RVU. All versions of T9101D41, starting with T9101D41^ADM, contain Version 5 of the spooler control file and are compatible with the T9101D46 and D48 product versions of spooler.
Overview of Installing G06.28 SCF Storage Subsystem (Online Disk Remirroring) For more information on proper shutdown of the spooler, see Support Notes S97057 (T9101D41 Spooler Collector Data Files Have Changed Format) and S99086 (NSK Spooler—Migration and Draining Instructions). CSPOOL Set at HIGHPIN Beginning with G06.19, a new spooler SPR, T9101D48^AEY, is introduced. This SPR is installed by DSM/SCM with CSPOOL at HIGHPIN.
Overview of Installing G06.28 TNS/R CRE Heap Manager TNS/R CRE Heap Manager The G06.15 RVU introduced a new heap manager, NSK CRE/RTL (T1269), an alternative to the Native CRE/RTL product (T8431). You can choose either heap manager during the creation of a system configuration revision. Consequently, the choice of which one to install is an independent decision for your system. For migration considerations, see Support Note S02001. For installation instructions, see Support Note S03104.
Overview of Installing G06.28 • • • SP Firmware Enterprise Storage System (ESS). The CT9841FC-x tape drive (introduced in G06.24), which is a replacement for CT9840FC-x tape products. New Fibre Channel disks available starting in G06.27. SP Firmware Before you update SP firmware, HP recommends that you download the SP firmware file to your system console. (See Download the SP Firmware File to the System Console (Optional) on page 7-6.
Overview of Installing G06.28 TMF upgrading from a pre-G06.20 RVU, back up your HP NonStop TCP/IP configuration files before running ZPHIRNM. (HP recommends backing up your TCP/IP configuration files before running ZPHIRNM even if you are on a G06.20 or later RVU.) If you have to restore information on network services and connections, you will need these files for the proper network information.
Overview of Installing G06.28 TMF softdoc for detailed migration information for TMF. See also the TMF Planning and Configuration Guide and the TMF Operations and Recovery Guide. If you have not run the Install SQL/MX script on your system while running the new RVU, and you have not created any native-format SQL/MX metadata tables (or their resource forks) or audit records for them, there are no TMF fallback considerations.
Overview of Installing G06.28 TNOS Server and TNOS Utility Falling Back from TMF 3.3 If you add one or more auxiliary audit trails while TMF is started, you can fall back only to G06.24 or a later RVU because the TMF audit reading facilities prior to the G06.24 RVU cannot handle auxiliary pointer (AUXPTR) records that specify a variable number of audit trails. (Once configured, the number of audit trails generally remains constant).
Overview of Installing G06.28 Visual Inspect Visual Inspect G06.20 and later RVUs include the Inspect subsystem (T9226G06 or later) and the Visual Inspect server (T9756AAH or later) that support PIC programs and DLLs. This product version of the server requires product version 2.4 of the Visual Inspect client (T7877AAD). If you run client product version 2.3 with a G06.
Overview of Installing G06.28 ServerNet Cluster ServerNet Cluster Starting in G06.28, the HP NonStop ServerNet Switch (model 6780) can support the long-distance option in a three-zone configuration of the layered topology. Prior to G06.28, the long-distance option was restricted to a two-zone configuration. To use the new ServerNet Cluster long-distance option in a three-zone configuration, you must install the G06.28 or later RVU or the T0502G08^AAQ or later SPR.
Part I. Upgrade Tasks Part I describes the tasks for upgrading a single NonStop S-series server to the G06.28 RVU, as follows: • • • • • • • • • • • • Section 2, G06.28 Upgrade Checklists Section 3, Installing SPRs Before Upgrading to the G06.28 RVU Section 4, Preparing to Upgrade the Server Software Section 5, Installing the G06.28 RVU Section 6, Replacing the Disk Bootstrap Microcode (Pre-G06.
Part I. Upgrade Tasks G06.
2 G06.28 Upgrade Checklists Use the checklist in Table 2-1 as you perform the tasks required to upgrade to the G06.28 RVU and the checklist in Table 2-2 to record the information needed when performing these tasks. Task durations are included in Table 2-1. Most of these baseline durations were established on an NonStop S72002 server running the G06.12 RVU under minimal load (one user).
G06.28 Upgrade Checklist G06.28 Upgrade Checklists Table 2-1. G06.28 Upgrade Checklist (page 2 of 3) Task Description Minimum Duration Documentation 8. Receive G06.28 RVU SUT into the DSM/SCM software archive 33 minutes (Full SUT, all products) Receive New Software Into the Archive on page 5-3 and follow Alerts on page 5-1. 9. Install and configure TSM or OSM SPRs (optional)** 40 minutes*** See the OSM Migration Guide and TSM softdocs. 10. Create G06.
G06.28 Upgrade Checklist G06.28 Upgrade Checklists Table 2-1. G06.28 Upgrade Checklist (page 3 of 3) Task Description Minimum Duration 24. Check processor status <1 minute Check Processor Status (Using TSM or OSM) on page 12-4 25. Configure WANMGR (if necessary) 20 minutes Upgrade the WAN Manager (T8365) (Optional) on page 12-16 26. Update SWAN concentrator CLIP firmware (if necessary) 4 minutes per SWAN concentrato r Appendix C, Updating SWAN Concentrator CLIP Firmware 27.
G06.28 Required Information Checklist G06.28 Upgrade Checklists G06.28 Required Information Checklist Table 2-2. G06.28 Required Information Checklist Type of Information Value Volume where SYSnn subvolumes are located (usually $SYSTEM) Current SYSnn (before upgrading to G06.28) SYSnn created during G06.
3 Installing SPRs Before Upgrading to the G06.28 RVU This section describes the SPRs you should install on your current RVU before you upgrade to the G06.28 RVU. SPRs provide new features between RVUs or correct previous software problems. Alerts • • • • • • • Before installing an SPR: ° Do not apply any SPR unless you verify that you can apply it to your current G-series RVU.
Installing SPRs Before Upgrading to the G06.28 RVU • SPRs Required Before Upgrading Before connecting a NonStop S-series system to an Integrity NonStop NS-series system through an IOAMF2 CRU, you must first update the firmware for both the S-series Gigabit 4-port ServerNet adapter (G4SA) and Fibre Channel ServerNet adapter (FCSA). Firmware for both the G4SA and FCSA adapters used for S-series systems is not initially compatible with NS-series systems. See the H06.
Installing SPRs Before Upgrading to the G06.28 RVU Summary of the SPR Installation Procedure Summary of the SPR Installation Procedure 1. Use Scout to verify that you can apply the DSM/SCM SPR to your current G-series RVU. 2. Use DSM/SCM to install the required SPRs. For detailed instructions, see Appendix A, Using DSM/SCM to Install SPRs. 3. Update the firmware or boot code if needed. Update also any Maintenance Entity (ME) firmware. 4.
Installing SPRs Before Upgrading to the G06.28 RVU DSM/SCM Client and Server Compatibility $TDSV ZDSMSCM 8> vproc cbexe VPROC - T9617G03 - (07 AUG 2003) SYSTEM \TINY Date 18 AUG 2004, 13:36:49 Copyright 2003 Hewlett-Packard Development Company, L.P.$TDSV.ZDSMSCM.
Installing SPRs Before Upgrading to the G06.28 RVU DSM/SCM Client and Server Compatibility Table 3-1. DSM/SCM Client and Server Compatibility This version of the DSM/SCM Planner Interface... With this version of DSM/SCM server software... T6030D30^AAT T6030D30/T6031D30 (pre-AAO) T6030D30^AAT T6030D30/T6031D30 (AAO and later), T6031D31, or T6031D46 Results in... You can perform all DSM/SCM functions available with the DSM/SCM product version you are running.
Installing SPRs Before Upgrading to the G06.28 RVU Fallback SPRs Fallback SPRs You must install fallback SPRs on your system before upgrading to the G06.28 RVU, or fallback is not possible. NonStop SQL/MP Fallback SPRs As of G06.13, the SQL/MP Format 2 partitions program provides the ability to extend the existing 2 GB partition limit up to a maximum of 1 terabyte (TB). No fallback SPRs are available to fall back to pre-G06.03 RVUs. Fallback SPRs are available for G06.03 through G06.13.
Installing SPRs Before Upgrading to the G06.28 RVU Interoperability SPRs Table 3-3. SPRs Required for NonStop SQL/MX Release 2.0 Fallback Product DP2 SPR (or Superseding) Notes T9053APO, if the system uses the online disk remirror feature If applied, a system load is required before upgrading to the new RVU. The SPRs are applicable to the G06.13 through G06.22 RVUs. See DP2 on page 1-29.
Installing SPRs Before Upgrading to the G06.28 RVU RDF Interoperability SPRs Table 3-4. Interoperability SPRs for NonStop NS-Series and NonStop S-Series Systems Minimum SPR Product Name Description Introduced in this RVU T0294 AAP SNETMON Required for ServerNet clustering G06.26 T9205 ACF TACL Required for remote NEWPROCESS of OCA objects G06.26 T9621 ABB Binder Required to recognize OCA region G06.27 T9674 AAM PDTSHARE Required to recognize OCA region G06.
Installing SPRs Before Upgrading to the G06.28 RVU SQL AUDSERV Interoperability SPRs Table 3-5. RDF Interoperability SPRs If a primary or backup node within the RDF environment is running this RVU... And any other node in the RDF environment is upgraded to a G06.00 or later or D46.00 or later RVU, install this (or a superseding) SPR on the down-level node... D32.00 through D39.00 T5864ABD D42.00 through D45.00 T5864ABE G02.00 through G05.
Installing SPRs Before Upgrading to the G06.28 RVU Configuring OSM Server Settings VST937.vsd If you are running a version of OSM released with G06.25 or later, the versions reported in this dialog box for each OSM component should match, as all OSM serverbased components were bundled into T0682. The OSM server-based SPR for G06.28 is T0682G07^AAL. HP recommends always using the latest OSM SPR. To see whether an OSM upgrade is required for your situation, see OSM and TSM on page 1-5.
Installing SPRs Before Upgrading to the G06.28 RVU Determining the Current Version of TSM Server Software latest TSM client software even if you have to fall back to an earlier RVU. TSM client T8154ABI (2005A) is compatible with server versions T7945AAG and later. Follow the installation instructions outlined in the softdoc, including preinstallation and post-installation steps. Determining the Current Version of TSM Server Software 1. At the TACL prompt, enter: VPROC $SYSTEM.SYSnn.SRM 2.
Installing SPRs Before Upgrading to the G06.28 RVU Determining the Current Version of TSM Server Software G06.
4 Preparing to Upgrade the Server Software Use this section to perform these tasks before you upgrade your server software: 1. 2. 3. 4. 5. Save the Current Configuration File (CONFxxyy) Upgrade the System Console Software Verify System Operations Record the Current SYSnn Back Up Important Files Save the Current Configuration File (CONFxxyy) A saved system configuration file contains a copy of the current configuration database CONFIG file, saved for future use.
Preparing to Upgrade the Server Software Upgrade the System Console Software If you specify a configuration file that already exists, SCF asks if you want to replace it. If you specify that you do not want to replace the existing file, SCF does not overwrite the file. You must enter another SAVE command to save the current configuration file.
Preparing to Upgrade the Server Software Upgrade the System Console Software See the NonStop System Console Installer Guide for the current PVUs of these products. To install the DSM/SCM client software (T6031ABG), see Appendix B, Installing the Latest DSM/SCM SPRs and Client Software. Starting with the G06.24 RVU, the CSSI Web snapshot is no longer provided on the installer CD, but the CSSI content can be accessed within NTL through the Support and Service library.
Preparing to Upgrade the Server Software Verify System Operations Verify System Operations Verify the integrity of your current system environment to ensure your system is operating normally before you install the G06.28 RVU by checking Table 4-1. Table 4-1. Verify System Operations Steps Activity 1. Check Processor Status (Using Either TSM or OSM) Done? Using TSM Using OSM 2. Check Critical System Processes Using TSM Using OSM 3. 4. 5. 6. 7. 8.
Preparing to Upgrade the Server Software Check Processor Status (Using Either TSM or OSM) VST932.vsd 2. On the toolbar, click Processor Status. VST933.vsd The Processor Status dialog box appears. The Processor Status for all processors should be Executing NonStop OS. G06.
Preparing to Upgrade the Server Software Check System Enclosure Components (Using TSM) If a different status appears, determine the problem and correct it: • • Check EMS messages or messages at the TACL prompt. Check the halt codes appearing in the Processor Status box. Check System Enclosure Components (Using TSM) Verify the operational status of the components in each system enclosure: 1. Log on to the TSM Service Application. 2. Check for alarm conditions in the tree pane of the management window.
Preparing to Upgrade the Server Software Check System Enclosure Components (Using TSM) VST200.vsd G06.
Preparing to Upgrade the Server Software Check Processor Status (Using OSM) 3. Select an item in the tree pane that shows alarm conditions, and then click the Alarms tab to view the alarms associated with the selected item. • • If a yellow triangle appears over an enclosure diagram, determine the cause of the problem. Correct the problem if possible. Determine if you can proceed without affecting the installation of software.
Preparing to Upgrade the Server Software Check Processor Status (Using OSM) VST933.vsd 2. Click System Discovery. 3. Select Processor Status. The Processor Status dialog box appears. The Processor Status for all processors should be Executing NonStop OS. For example: G06.
Preparing to Upgrade the Server Software Check Processor Status (Using OSM) Check System Components (Using OSM) Note. Do not launch the OSM Service Connection if you do not already have OSM server processes configured. If OSM is not installed, use TSM to migrate to the G06.28 RVU. 1. Log on to the OSM Service Connection. If you have not used OSM before or if you have any problems accessing OSM, see the OSM Migration Guide or the most current OSM softdoc.
Preparing to Upgrade the Server Software Check Processor Status (Using OSM) Beginning with G06.24, the OSM Service Connection browser session starts in a new browser window and eliminates the use of standard Internet Explorer buttons. (Clicking the Internet Explorer’s Refresh ends your current OSM Service Connection session and forces you to open a new browser window to reestablish a new connection to the system you are monitoring.
Check Critical System Processes Preparing to Upgrade the Server Software 2. The System Status window indicates the overall health of a system by the color of the system icon. Green indicates that the overall health is fine; yellow indicates a possible system problem. From the Summary menu, select System Status. For example: 3. Select an item in the tree pane that shows alarm conditions, and then click the Alarms tab to view the alarms associated with the selected item.
Check the Status of the SACs Preparing to Upgrade the Server Software 140 142 196 199 205 $ZTN20 2,287 3,273 (46,0 ) 6144 $ZTC20 2,286 3,272 (48,0 ) 32000 $ZPHI 0,268 1,288 ( 1,0 ) 4024 $Z14W 3,35 ( 1,30) 132 $Z14X 2,23 ( 1,30) 132 170 200 198 150 150 \ELI.$SYSTEM.SYS00.TELSERV \ELI.$SYSTEM.SYS00.TCPIP \ELI.$SYSTEM.SYS00.EMSACOLL \ELI.$SYSTEM.SYS00.EMSDIST \ELI.$SYSTEM.SYS00.
Check the Swap File Configuration Preparing to Upgrade the Server Software LDev Primary 146 *STARTED Backup Mirror MirrorBackup Primary PID Backup PID STARTED *STARTED STARTED 0,299 1,267 MirrorBackup Primary PID 0,291 Backup PID 1,276 STORAGE - Status DISK \ELI.$AUDIT LDev Primary Backup Mirror 177 *STARTED STARTED *STARTED STARTED 3. If the $SYSTEM, DSM/SCM, and Archive volumes are not listed in the display, contact your service provider. 4.
Check the Status of the Spooler Collector Preparing to Upgrade the Server Software 4. From NSKCOM, perform a STATUS to verify which swap files are in use. For example: 4> nskcom status swapfile * NSKCOM - T5838G05 BASE (04AUG98) - Jul 27 1998 Copyright (c) 1995, 1997 Tandem Computers Incorporated $SYSTEM.SYSTEM.ZSYSCFG KMS.SWAPFILE = 0 $AUDIT0.ZSYSSWAP.CPU0 KMS.SWAPFILE = 1 $AUDIT0.ZSYSSWAP.CPU1 KMS.SWAPFILE = 2 $AUDIT0.ZSYSSWAP.CPU2 KMS.SWAPFILE = 3 $AUDIT0.ZSYSSWAP.CPU3A . . . Status of $AUDIT0.
Check the Tape Drive Status Preparing to Upgrade the Server Software Check the Tape Drive Status Check that the tape drive to be used to install the SUT is started and online: 1. At a TACL prompt, enter: > SCF STATUS TAPE $* 2. Verify that the STATUS TAPE display includes the tape subsystem you plan to use to load the SUT. For example: STORAGE - Status TAPE \ELI.$SILO2 LDev State Primary Backup PID PID 138 STARTED 0,295 1,279 DeviceStatus ONLINE 3.
Preparing to Upgrade the Server Software Record the Current SYSnn CRE/RTL (T1269) Enter the following command to find out which version of Heap Manager is currently installed: VPROC $SYSTEM.SYSTEM.ZCRESRL If VPROC shows that T1269 is installed, then you must delete product T8431 from the upgrade configuration. Record the Current SYSnn Identify and record the current SYSnn subvolume on your system. You will have to specify this SYSnn subvolume if you need to fall back from the G06.28 RVU.
Preparing to Upgrade the Server Software Back Up Important Files G06.
5 Installing the G06.28 RVU Installing a new RVU involves these DSM/SCM tasks: 1. Receive New Software Into the Archive 2. Create a New Software Revision 3. Build and Apply the New Software Revision Alerts Do not use this procedure to upgrade more than one NonStop S-series server at a time or to install SPRs. Before you install the G06.28 RVU, these requirements must be met: • Always install the latest PVU or SPR of DSM/SCM and the DSM/SCM client before receiving the SUT.
Installing the G06.28 RVU • Back Up Important Files Obtain a user name and password authorized to use the DSM/SCM Planner Interface. See the DSM/SCM User’s Guide for more information about configuring which users are allowed to use DSM/SCM and which tasks they are permitted to perform. Note. Safeguard aliases are case-sensitive and must be entered exactly when you log on to DSM/SCM. You can add a Safeguard alias anytime when Safeguard is running and before installing the SUT.
Installing the G06.28 RVU Receive New Software Into the Archive Receive New Software Into the Archive Receiving software into the Archive might take several hours. To receive the SUT containing the G06.28 RVU into the DSM/SCM Archive: 1. Start TMF and DSM/SCM if they are not already running. For example: > TMFCOM START TMF > VOLUME $dsmscm_vol.
Installing the G06.28 RVU Receive New Software Into the Archive vst500.vsd 4. In the Software in Archive dialog box, click Receive software. The Receive Software Request dialog box appears. For example: VST505.vsd G06.
Installing the G06.28 RVU Receive New Software Into the Archive 5. In the Receive Options group box, do the following, depending on your system environment: ° ° Select Receive only changed files, which is the default. Select Receive all files if you are on a pre-T6031^ABE SPR. If you select this option, the apply might take over an hour if you are upgrading from a preG06.18 RVU. 6. Under Software name, select Provided by planner and enter a name for the RVU. 7. Under Options, click Input source.
Installing the G06.28 RVU Receive New Software Into the Archive 12. While waiting for the request to finish, check: • • The status of the request in the Status window. For example: EMS event messages to see if a new reel (or cartridge on a nonautoloading drive) of the SUT needs to be mounted. EMS messages are displayed in the following windows: ° ° The OutsideView EMS Event Stream window The EMS Events window displayed by DSM/SCM when you click Show EMS events from the Status window G06.
Installing the G06.28 RVU Receive New Software Into the Archive 13. Select Requests>Requests list to check that the request is finished: VST525.vsd 14. When the request is finished, close the Status and Requests windows. 15. Update the Software in Archive dialog box to show the newly received SUT. Select Window>Refresh. The new SUT appears in the window: vst556.vsd 16. Keep the Planner Interface open for the next task. G06.
Create a New Software Revision Installing the G06.28 RVU Create a New Software Revision When you create a new software revision, DSM/SCM selects the products in the SUT that are licensed for your site and replaces any previous versions of the products. The following steps assume that you are creating a new software revision that manages OSS files. If you are not, go to Step 6 after you open the Planner Interface Configuration Revisions dialog box.
Create a New Software Revision Installing the G06.28 RVU 2. In the Planner Interface, in the Configuration Revisions dialog box, select the target configuration. 3. Select Maintain>Target Maintenance>Modify. a. Select the Manage OSS Files option. Manage OSS Files VST447.vsd b. Click Output to view the default ouput values. c. Enter default output values in the data fields as needed. d. Click OK. G06.
Installing the G06.28 RVU Create a New Software Revision . Note. If you receive this error message stating that the current target is pre-D46, you can continue with the installation if you are certain that you have installed the DSM/SCM T6031D46 PVU or later SPR. To check the correct product version: 1. Enter these DSM/SCM VPROC commands: > volume $dsmscm_vol.ZDSMSCM > vproc taexe > vproc cbexe 2. Log on to TI by running ZPHITI (page 5-19). The current target version appears. > RUN ZPHITI 3.
Installing the G06.28 RVU Create a New Software Revision b. Add a description describing the new software revision (such as G06.28 SUT) and click OK. c. On the Software in Archive window, select the G06.28 RVU that was just received into the archive and click Copy to. vst561.vsd 7. Click Continue when the Confirmation message appears: The current contents of the new revision will be deleted. Products named in this target’s custfile will be required for the new revision. vst560.
Installing the G06.28 RVU Create a New Software Revision in the previous configuration. (These products are removed from the system by DSM/SCM during the Build/Apply of the new configuration.) An example of a product version mismatch might occur when T9225D46 (TNS/R C++ Compiler) is installed using DSM/SCM. If you are not currently running TT9225D46, the Planner Interface displays a "Version Mismatch" message to indicate that the version of this SPR is different from the version of the base component.
Installing the G06.28 RVU Build and Apply the New Software Revision 9. Keep the Planner Interface open for the next task. Build and Apply the New Software Revision The Build process creates an activation package containing all the products listed in the new software revision. Note. The Activation Package contains installation instructions for the pax files of those OSS products that contain A7CINFO files in their distributed subvolumes.
Installing the G06.28 RVU Build and Apply the New Software Revision Note. You might receive this message: The message is warning you that the last DSM/SCM snapshot was created by a pre-T6031D46 version of DSM/SCM, which would be the case if you have not installed the T6031D46 product version. If you are certain that you are on a D46 or later PVU of DSM/SCM, ignore the message and continue with the G06.28 installation.
Installing the G06.28 RVU Build and Apply the New Software Revision 2. Under Perform steps, select Build, apply & process snapshot. 3. In the Activation SYSnn: box, enter a unique number to create a new SYSnn subvolume. The value nn must be a two-digit octal number in the range%00...%77. You can issue a FILEINFO command at a TACL prompt to view the SYSnn subvolumes that are currently on your system. (For other ways to determine the SYSnn, see Determine the Current SYSnn on page A-3.) > fileinfo $system.*.
Build and Apply the New Software Revision Installing the G06.28 RVU 6. Edit the instructions to provide the correct (new) SYSnn number, and then click OK. The Planner Instructions box closes. 7. Select the Scheduling, Output, SYSGEN, TSV Location, and File Placement options and configure as appropriate for your system. (See the DSM/SCM User’s Guide or the online help for more information about Build/Apply Request options.
Installing the G06.28 RVU Build and Apply the New Software Revision 10. Check EMS messages for more detailed information about your Build/Apply: a. In the Events window, click Refresh to see newer messages. b. When finished viewing, click Close. Note. If you encounter any problems, see the DSM/SCM User’s Guide or online help.
Installing the G06.28 RVU • • Build and Apply the New Software Revision The last message in the EMS Events window shows that the input snapshot finished successfully. The Requests window shows that the request is finished. (Select Requests> Requests list). 11. Close the EMS Events, Status, and Request windows. 12. Exit the DSM/SCM Planner Interface. G06.
Print Operator Instructions From the Target Interface (ZPHITI) Installing the G06.28 RVU Print Operator Instructions From the Target Interface (ZPHITI) Print the operator instructions that you edited in Step 6 on page 5-16. 1.
Installing the G06.28 RVU Print Operator Instructions From the Target Interface (ZPHITI) 3. From the ZPHITI Main Menu, enter 3 (Perform target activities) in the Selection number field, and press F1 to display the Target Menu - Select Target screen.
Installing the G06.28 RVU Print Operator Instructions From the Target Interface (ZPHITI) An example might look like this: Activation Instructions for \WARRIOR DEFAULT These are general instructions that were determined from configuration attributes. Refer to the release documentation for detailed information on migrating to this software configuration. 1. Stop all applications. Keep OSS running. 2. Update FIRMWARE. Run TMDS (or TSM for S-Series) to check firmware and perform firmware updates.
Installing the G06.28 RVU Recovery for Problems Installing the G06.28 RVU Recovery for Problems Installing the G06.28 RVU If you receive an error indication in the Requests, Status, or EMS Events windows, you might have to reinitiate the Build/Apply. See the DSM/SCM Messages Manual to determine the nature and severity of the problem. Cancel Pending Build/Apply Requests Note.
Installing the G06.28 RVU Cancel Pending Build/Apply Requests d. Click OK. You must always use the new software input instead of the previously received software input brought into the Archive. G06.
Installing the G06.28 RVU Cancel Pending Build/Apply Requests G06.
6 Replacing the Disk Bootstrap Microcode (Pre-G06.06) As of the G06.06 RVU, a new disk bootstrap program is available. If you are migrating to the G06.28 RVU from an RVU prior to G06.06, you must replace the existing disk bootstrap microcode with this new version, as described in this section. If you update the disk boot code, you must down the mirrored disk. The mirror should be revived as soon as possible after performing a system load. In this procedure, you use the SCF CONTROL DISK, REPLACEBOOT command.
Replacing the Disk Bootstrap Microcode (PreG06.06) G06.
7 Updating Service Processor (SP) Firmware SP firmware performs vital functions for NonStop S-series servers. This section describes how to update the SP firmware to the proper version when upgrading to a new RVU. Table 7-1 provides an overview of firmware and SP components. Note. Update SP firmware only: • • If instructed to do so by DSM/SCM If you are not replacing the PMF CRUs in your system while migrating to the G06.
Updating Service Processor (SP) Firmware Alerts Alerts • • • • • • • • • • When using the TSM Service Application to update the service processor firmware, use the Firmware Update dialog box. Do not use the Single SP Firmware dialog box unless instructed to do so to recover from a failed service processor update. Check that no other service processor firmware updates are in progress before updating service processor firmware.
Before You Begin Updating Service Processor (SP) Firmware Before You Begin 1. Verify that the system is up with at least one processor running the NonStop operating system. 2. Verify that you know the SYSnn for the new RVU and for your current RVU. See Check Processor Status (Using Either TSM or OSM) on page 4-4. • • The SYSnn for your current RVU was determined in the Record the Current SYSnn procedure on 4-17. The SYSnn for the G06.
Determine the Current and New Versions of SP Firmware Updating Service Processor (SP) Firmware Determine the Current and New Versions of SP Firmware When updating SP firmware, you need: • • The SP firmware version for your current RVU to determine that the SPs are in a known, good state before you begin the SP firmware update The SP firmware version for the G06.
Updating Service Processor (SP) Firmware Verify That Your Current RVU Is Running the Correct Version of SP Firmware (Using TSM) Verify That Your Current RVU Is Running the Correct Version of SP Firmware (Using TSM) 1. Log on to the TSM Service Application. 2. Select Display>SP Actions. The Service Processor Actions dialog box appears. Wait for the firmware version of each SP to appear (this might take several minutes). 3.
Updating Service Processor (SP) Firmware Download the SP Firmware File to the System Console (Optional) 5. Click OK in response to this message: This action takes up to 2 minutes for the SP to complete the reset even if the action appears to complete immediately. This action will cause any current Firmware Update actions against this SP to abort. Verify there are no Firmware Updates being performed on this SP before continuing. Are you sure you want to reset this SP? 6.
Updating Service Processor (SP) Firmware Download the SP Firmware File to the System Console (Optional) vst642.vsd 6. Click OK. The Browse window closes, and an IXF - Receive dialog box appears, showing the download progress of the spntcde9 file. The download should take around 5 minutes. 7. When the IXF - Receive dialog box indicates that the transfer is finished, click End Transfer. G06.
Updating Service Processor (SP) Firmware Update SP Firmware Using the TSM Service Application Update SP Firmware Using the TSM Service Application 1. If necessary, log on to the TSM Service Application. 2. If necessary, display the Service Processor Actions dialog box, either by selecting SP Actions on the toolbar or by selecting Display>SP Actions. G06.
Updating Service Processor (SP) Firmware Update SP Firmware Using the TSM Service Application vst630.vsd 3. Using the Service Processors (SPs) list, determine which fabric (X or Y) contains the secondary master service processor. You must select this fabric when you begin updating service processor firmware: • • If an asterisk appears on the line for GRP-1.MOD-1.SLOT-50, the Y fabric contains the secondary master service processor. Select the Y fabric for the remaining steps in this procedure.
Updating Service Processor (SP) Firmware Update SP Firmware Using the TSM Service Application 4. Select Display>Firmware update. The Firmware Update dialog box appears. 5. From the Resource Type list, select Service Processors, Y-side if you have chosen to update the service processors in the Y fabric, or Service Processors, X-side if you are updating the service processors in the X fabric. 6. From the Display list, select All to display the selected resources in the Available area. VST645.vsd 7.
Updating Service Processor (SP) Firmware Update SP Firmware Using the TSM Service Application Specify Firmware File Location Enter firmware file location and name: $volume.subvolume $system.sys02 File name SPCODE9 VST646.vsd 10. Click OK. 11. Click Yes when a message appears, warning that you have specified a nonstandard firmware file location: You have specified a nonstandard firmware location. Compaq TSM will try to get the firmware information. It may take a few seconds.
Updating Service Processor (SP) Firmware Update SP Firmware Using the TSM Service Application The update starts, and the Firmware Update Action Summary dialog box appears. Updating each service processor takes approximately ten minutes, and updating a master service processor takes approximately twenty minutes. 13. Monitor the status of the service processor firmware update in the Firmware Update Action Summary dialog box. a.
Updating Service Processor (SP) Firmware Update SP Firmware Using the TSM Service Application 16. Verify that the correct firmware version is loaded for each SP: a. If necessary, log on to the TSM Low-Level Link Application and perform a System Discovery. (Do not log off the TSM Service Application.) b. Display the Service Processor Actions dialog box, either by clicking SP Actions on the toolbar or by selecting Display>SP Actions. c.
Updating Service Processor (SP) Firmware Update SP Firmware Using the TSM Service Application If all SPs were updated successfully, you can skip to Section 8, Updating Processor Boot Code on page 8-1. Otherwise, continue with Determining If a Problem Has Occurred on page 7-15 to diagnose and correct problems you encountered. G06.
Updating Service Processor (SP) Firmware Determining If a Problem Has Occurred Determining If a Problem Has Occurred Note. After the firmware update finishes and the SP is successfully reset, it can take up to 20 minutes before the Service Processor Firmware Version attribute is updated to display the new information. Follow all the verification steps included in the SP firmware update procedure. Otherwise, you might not know that the firmware update or reset did not finish successfully.
Updating Service Processor (SP) Firmware Other Indications of SP Firmware Update Problems If any of these problems occur, see Recovery for Problems Updating SP Firmware (Using TSM) on page 7-16.
Updating Service Processor (SP) Firmware Checking the State of the Service Connection Checking the State of the Service Connection 1. Using the TSM Service Application, open the Service Processor Actions dialog box, either by clicking SP Actions on the toolbar or by selecting Display>SP Actions. 2. From the Available Actions list, select SP Responsive Test. 3. Select the SP you want to test by clicking on it in the Service Processors (SPs) list. 4. Click Perform action. 5.
Updating Service Processor (SP) Firmware Updating Firmware Using the TSM Low-Level Link Application (Optional) Updating Firmware Using the TSM Low-Level Link Application (Optional) If you are unable to use the TSM Service Application, you can still update each SP by using the TSM Low-Level Link Application, if you have downloaded the firmware file spntcde9, as described under Download the SP Firmware File to the System Console (Optional) on page 7-6.
Updating Service Processor (SP) Firmware Resetting an SP Using the TSM Low-Level Link Application This action takes up to 2 minutes for the SP to complete the reset even if the action appears to complete immediately. This action will cause any Firmware Update actions against this SP to abort. Verify there are no Firmware Updates being performed on this SP before continuing. Are you sure you want to reset this SP? 7.
Updating Service Processor (SP) Firmware Updating SP Firmware Using the OSM Service Connection Updating SP Firmware Using the OSM Service Connection Use this procedure only if OSM is installed and configured. If TSM is installed and is your default, use the TSM Service Connection to update SP firmware. Notes for Using OSM to Update SP Firmware • • • • The Multi-Resource Actions dialog box is used to update the SP firmware. After the SP firmware update is complete, you are asked to reset the SP.
Updating Service Processor (SP) Firmware Firmware Update for Fabric Side-Y (Using OSM) 3. Select Display>Multi-Resource Actions. The Multi-Resource Actions dialog box appears with unselected fields. VST938.vsd 4. From the Resource Type list, select SP. 5. From the Action list, select SP Firmware Update. 6. From the Filter by list, select the appropriate filter, Logical:Fabric Side-Y, first. For example: VST939.vsd G06.
Updating Service Processor (SP) Firmware Firmware Update for Fabric Side-Y (Using OSM) It might take a minute or so for the SPs to appear in the SP Firmware list. At this point in the update process, the Compare State displays Same. For example, the current firmware version might display T1089G06^07NOV03^27OCT03^ABL: VST949.vsd (After the firmware update is complete with the SPs reset, the Compare State displays Up-rev, and the firmware Version displays the new firmware file version.) 7.
Updating Service Processor (SP) Firmware Firmware Update for Fabric Side-Y (Using OSM) The SP - Parameter Input dialog box appears. 10. Enter the new file location. Use the $volume.subvolume.filename created during the most recent DSM/SCM Build/Apply, and click OK. For example: After you click OK, the number of SPs that are currently being updated appears in the Running column under SP Firmware Update Progress. For example: vst945.
Updating Service Processor (SP) Firmware Firmware Update for Fabric Side-Y (Using OSM) VST946.vsd You are then asked to reset each SP: The firmware update needs to reset the Service Processor to activate the updated firmware. Would you like to reset the Service Processor? 11. Click Yes. The number of SPs that are currently being updated appears in the Running column under SP Firmware Update Progress: VST966.vsd The reset message appears for all SPs that must be reset.
Updating Service Processor (SP) Firmware Firmware Update for Fabric Side-X (Using OSM) Firmware Update for Fabric Side-X (Using OSM) Note. You can begin this procedure for updating the X-side by using Remove All to delete the resources for the Y-side update. (All the steps are the same, except the change filter message is not displayed, and Step 2 is unnecessary.) 1. From the Filter by list, select the appropriate filter, Logical:Fabric Side-X.
Updating Service Processor (SP) Firmware Verifying the SP Firmware Update (Using OSM) You are then asked to reset each SP: The firmware update needs to reset the Service Processor to activate the updated firmware. Would you like to reset the Service Processor? 7. Click Yes. The Reset Progress bar keeps track of the number of SPs that pass the firmware reset. After a few minutes, the SP is reset.
Updating Service Processor (SP) Firmware Verifying the SP Firmware Update (Using OSM) 8. Click Close. If all SPs were updated successfully, you can skip to Section 8, Updating Processor Boot Code. Otherwise, continue with Correcting a Failed SP Firmware Update (Using the OSM Service Connection) on page 7-28 to diagnose and correct problems you encountered. G06.
Updating Service Processor (SP) Firmware Correcting a Failed SP Firmware Update (Using the OSM Service Connection) Correcting a Failed SP Firmware Update (Using the OSM Service Connection) When an SP fails to update using the multiple firmware update, the number of failed SPs is displayed in the Failed column, and a red X appears by the SP that failed under Resource name in the SP Firmware resource list: 1. Select Action Summary from the SP Firmware Update Progress section. a.
Updating Service Processor (SP) Firmware Updating Firmware Using the OSM Low-Level Link (Optional) 5. If necessary, select Browse and enter the firmware file-name. The SP file (SPNTCDE9) and its directory appears in the Firmware File box. 6. Click Perform action. 7. A message appears telling you that the “action may take up to 30 minutes” for each SP. Click OK. 8. Wait for the SP to finish updating. 9. When all the SP updates finish successfully, reset them, as described in the OSM online help. WARNING.
Updating Service Processor (SP) Firmware Updating Firmware Using the OSM Low-Level Link (Optional) G06.
8 Updating Processor Boot Code Processor boot code controls device boot and power-on diagnostic functions. This section describes the two common methods for updating the processor boot code and how to use either the OSM Service Connection or TSM Service Application to update the processor boot code for each PMF CRU in your system. See Table 8-1. Table 8-1.
Updating Processor Boot Code Even if you are not installing new S88000s, if you try to update to T7892ABD boot millicode for other NonStop S-series processors, such as S74000, S78000, and so forth, a processor halt occurs. As documented in HS02865, there are at least three strategies for updating processor boot code firmware, with subsequent methods for reloading the processors. See HS02865 for further details.
Updating Processor Boot Code Before You Begin Updating the Boot Millicode Before You Begin Updating the Boot Millicode Check Processor Status Before you update boot code firmware, verify that the system is up with at least one processor running a G06.00 or later product version of the NonStop operating system: 1. If necessary, log on to the OSM Low-Level Link Application or the TSM Low-Level Link Application. 2. On the TSM or OSM toolbar, click Processor Status.
Updating Processor Boot Code Method 1: Using G06.24 or Later OSM or TSM SPRs, Update Processor Boot Code Using the 2. Record the version of the processor boot code. 3. Repeat Steps 1 and 2 by using the SYSnn for your current RVU. For example: $SYSTEM SUPER 7> vproc $system.sys01.cpucode8 VPROC - T9617G03 - (30 MAR 1999) SYSTEM \WARRIOR Date 21 SEP 2000, 11:49:55 COPYRIGHT TANDEM COMPUTERS INCORPORATED 1986 - 1995 $SYSTEM.SYS01.
Updating Processor Boot Code Using TSM, Update Processor Boot Code Using the Online Option and G06.24 or Later TSM SPRs Using TSM, Update Processor Boot Code Using the Online Option and G06.24 or Later TSM SPRs Beginning with TSM 2001D (client and server versions) in G06.14, you can update the processor boot code for NonStop S-series servers (S70000, S7x000, S7600, S7800, S7400, and S8x000) without taking the processor down for a Hard Reset action (or Reset, or Prime for Reload action).
Updating Processor Boot Code Using TSM, Update Processor Boot Code Using the Online Option and G06.24 or Later TSM SPRs 6. Click Specify other to display the Specify Firmware File Location dialog box. Specify Firmware File Location Enter firmware file location and name: $volume.subvolume $system.sys02 File name CPUCODE9 VST654.vsd 7. Enter the volume and subvolume where the file to use as the source for the update resides. Use the $SYSTEM.SYSnn created during the most recent DSM/SCM Build/Apply. 8.
Updating Processor Boot Code Using OSM, Update Processor Boot Code Using the Online Option and G06.24 or Later OSM SPRs T7892G07^25AUG03^AAY^22Jul03^ VST728.vsd 10. From the Firmware Update dialog box, click Perform action. The update starts, and the Firmware Update Action Summary dialog box appears. 11. Monitor the status of the processor boot code update in the Firmware Update Action Summary dialog box. For example: VST964.
Updating Processor Boot Code Using OSM, Update Processor Boot Code Using the Online Option and G06.24 or Later OSM SPRs VST938.vsd 3. From the Resource Type list, select Processor. 4. From the Action list, select Online Boot Millicode Firmware Update. 5. From the Filter by list, select Logical: Fabric Side-Y. 6. Click Add All to move the selected resources to update the firmware list: 7. Click Perform Action. 8. Click OK when the Confirm Processor Boot Millicode Firmware Update dialog box appears.
Updating Processor Boot Code Using OSM, Update Processor Boot Code Using the Online Option and G06.24 or Later OSM SPRs VST955vsd 10. To verify that firmware resets are in progress, click Action Summary. The Action Status Summary window appears with information about recent actions, including their status and overall progress. 11. Update the X-fabric for the processor boot code. From the Filter by list, select the appropriate filter, Logical:Fabric Side-X.
Updating Processor Boot Code Method 2: Using Your Current Pre-G06.24 OSM or TSM SPRs, Update the Processor Boot Code and Method 2: Using Your Current Pre-G06.24 OSM or TSM SPRs, Update the Processor Boot Code and Issue a Reset Action or Equivalent Note. You can also perform a hard reset or reset equivalent using the TSM Low-Level Link Application or OSM Low-Level Link on all processors when you use either TSM or OSM LowLevel Link Start System option instead of using the Reset action.
Updating Processor Boot Code Using TSM, Update the Processor Boot Code and Issue a Reset Action or Equivalent 5. Click Add all to move the resources to the Selected box. 6. Click Specify other to display the Specify Firmware File Location dialog box. 7. Enter the volume and subvolume where the file to use as the source for the update resides. Use the $SYSTEM.SYSnn created during the most recent DSM/SCM Build/Apply: G06.
Updating Processor Boot Code Using TSM, Update the Processor Boot Code and Issue a Reset Action or Equivalent Specify Firmware File Location Enter firmware file location and name: $volume.subvolume $system.sys02 File name CPUCODE9 VST654.vsd 8. Click OK. 9. Click Yes when this message appears: You have specified a nonstandard firmware location. Compaq TSM will try to get the firmware information. It may take a few seconds.
Updating Processor Boot Code Using TSM, Update the Processor Boot Code and Issue a Reset Action or Equivalent 11. Monitor the status of the processor boot code update in the Firmware Update Action Summary dialog box. For example: VST729.vsd When the action status appears as Completed, the processor boot code update is finished. 12. Repeat Steps 2 through 11 to update the Processor Boot Code, X-side.
Updating Processor Boot Code Using OSM, Update the Processor Boot Code and Issue a Reset or Equivalent Using OSM, Update the Processor Boot Code and Issue a Reset or Equivalent You can use OSM to update processor boot code, provided that you use the Reset or System Start (Prime for Reload) action option. This action can be done at the end of the procedure or when performing a system load. 1. Log on to the OSM Service Connection. 2. Select Display> Multi-Resource Actions.
Updating Processor Boot Code Using OSM, Update the Processor Boot Code and Issue a Reset or Equivalent VST955vsd 10. To verify that firmware updates are in progress, click Action Summary. The Action Status Summary window appears with information about recent actions, including their status and overall progress. A successful update (partial screen) for the Y-fabric of the processor boot code: 11. Update the X-fabric for the processor boot code.
Updating Processor Boot Code Using OSM, Update the Processor Boot Code and Issue a Reset or Equivalent When you change the Filter by list from Y-side to X-side, this message appears: Changing a required filter results in your selections being cleared. Do you still wish to change the filter? 12. Click OK. 13. Click Add All to add the SPs you want to update to the Processor Boot Millicode Firmware lower list. 14. Click Perform Action. 15.
Updating Processor Boot Code Reset the Processors To Complete Updating the Processor Boot Code (Both for OSM and TSM) Reset the Processors To Complete Updating the Processor Boot Code (Both for OSM and TSM) You must perform a Reset action or equivalent (Start System in the OSM or TSM LowLevel Link) of the processors after you have updated the processor boot code and if you did not select the explicit online boot code option in either TSM or OSM.
Updating Processor Boot Code Reset the Processors To Complete Updating the Processor Boot Code (Both for OSM and TSM) G06.
9 Updating SCSI Boot Code (Pre-G06.08 RVU) This section describes how to check and, if necessary, update SCSI boot code for each PMF CRU in your system. Note. Update SCSI boot code only: • • If instructed to do so by DSM/SCM If you are not replacing the PMF CRUs in your system while migrating to the G06.28 RVU. Note. If you are migrating to the G06.28 RVU from an RVU prior to G06.08, you must update SCSI boot code after you perform the system load of the G06.
Updating SCSI Boot Code (Pre-G06.08 RVU) Using TSM to Update SCSI Boot Code (If Necessary) Using TSM to Update SCSI Boot Code (If Necessary) Before you update SCSI firmware, verify that the system is up and running the G06.28 version of the NonStop operating system. This step is important if you are coming from a pre-G06.08 RVU. 1. If necessary, log on to the TSM Low-Level Link Application. 2. On the toolbar, click Processor Status. The Processor Status should be Executing NonStop OS. 3.
Updating SCSI Boot Code (Pre-G06.08 RVU) Using TSM to Update SCSI Boot Code (If Necessary) vst900.vsd 4. Select all resources that have a current version different from the file version recorded in SCSI Boot Code Product Numbers on page 9-1, and then click Add to move selected resources to the Selected box. If all firmware versions match, you do not need to perform the update for the selected fabric (X or Y). If you have not yet checked the firmware in the other fabric, repeat Steps 2 through 6.
Updating SCSI Boot Code (Pre-G06.08 RVU) Using OSM to Update SCSI Boot Code (If Necessary) Using OSM to Update SCSI Boot Code (If Necessary) Note. OSM can be installed only on G06.08 or later RVUs. Therefore, the IBOOT (T0503) file should already be installed. Instructions are provided when a new firmware file is introduced after the most current RVU is initially released. 1. Before you update SCSI firmware, verify that the system is up and running the G06.28 version of the NonStop operating system. 2.
10 Running ZPHIRNM During the Build/Apply phase, DSM/SCM places product files in their subvolumes with temporary (fabricated) file names so that new file names do not conflict with the file names of currently running programs. This section describes how to run the ZPHIRNM program on the target system to: • • Rename the files that currently have actual file names with fabricated names. These files become obsolete when the new files are renamed.
Running ZPHIRNM • • Back Up (Copy) Files in the $SYSTEM.ZTCPIP Subvolume If you are using DSM/SCM to manage OSS files, ZPHIRNM notifies you if and when to run the merge_whatis command. If ZPHIRNM is run in PREVIEW mode, ZMODGP is run in TRIAL mode. However, any errors in the new and changed files will not be discovered in preview or trial mode because ZPHIRNM in preview mode does not actually rename the files.
Running ZPHIRNM Stop All Applications Stop All Applications Before running ZPHIRNM: 1. Stop DSM/SCM if it is still running. For example: > VOLUME $dsmscm_vol.ZDSMSCM > Run STOPSCM STOP CNFGINFO server process $ZPHC STOP DSM/SCM Pathway system $YPHI PATHCOM $YPHI;SHUTDOWN !,WAIT $Z02H: TCP TCP-H, STOPPED $Z02H: TCP TCP-T, STOPPED STOP DSM/SCM Alternate EMS Collector $ZPHI where $dsmscm_vol is the DSM/SCM volume. Stop all other applications, except for perhaps TMF and the OSS file system. Note.
Running ZPHIRNM Back Up the Spooler Control Files See Support Note S99086, NSK Spooler—Migration and Draining Instructions, for more information. You can also review Section 1 and Appendix H in the Spooler Utilities Reference Manual. Back Up the Spooler Control Files While the spooler environment is closed, back up the spooler control files to render a known database from which you can recover in case of a catastrophic spooler failure. Make sure that you also Drain the Spooler (10-3).
Running ZPHIRNM Steps for Running ZPHIRNM Note: TMF is not required to be running during the real ZPHIRNM because no SQL program files need to be renamed. PREVIEW mode also reveals most errors that ZPHIRNM would encounter if it were run. If errors are revealed, you can evaluate and correct them interactively. The syntax for running ZPHIRNM in PREVIEW mode is (from the DSM/SCM subvolume): > RUN ZPHIRNM [$vol.]SYSnn , PREVIEW [STRICT] [,option] ...
Running ZPHIRNM Steps for Running ZPHIRNM Activating configuration: DEFAULT 9 1 2 3 4 5 6 7 8 9 10 11 71 72 73 74 75 76 77 78 79 80 81 .dsmscm.ZMP00007 .dsmscm.ZMP00007 .dsmscm.ZMP00007 .dsmscm.ZMP00007 .dsmscm.ZMP00007 .dsmscm.ZMP00007 .dsmscm.ZMP00007 .dsmscm.ZMP00007 .dsmscm.ZMP00007 .dsmscm.ZMP00007 .dsmscm.ZMP00007 . . . .dsmscm.ZMP00007 .dsmscm.ZMP00007 .dsmscm.ZMP00007 .dsmscm.ZMP00007 .dsmscm.ZMP00007 .dsmscm.ZMP00007 .dsmscm.ZMP00007 .dsmscm.ZMP00007 .dsmscm.ZMP00007 .dsmscm.ZMP00007 .dsmscm.
Running ZPHIRNM Steps for Running ZPHIRNM Number of files renamed back during undo processing ............ 0 For managing OSS files, you might see a display similar to this: OSS: Directories: Directories in new configuration .................. Directories in old configuration .................. 110 110 Directories in new configuration only ............. Directories in old configuration only ............. Directories shared by new and old configurations ..
Running ZPHIRNM Steps for Running ZPHIRNM Total Warnings ... 0 Note: merge_whatis needs to be run to update the man pages. whatis.frag directory have changed. Files in a ZPHIRNM for $SYSTEM($WHIT4).SYS01 finished successfully. 4. Run the OSS merge_whatis command. (The merge_whatis command is a shell script in /bin that creates and updates the whatis database used by the OSS shell man, apropos, and whatis commands.
Running ZPHIRNM Verify That ZPHIRNM Ran Successfully 5. If necessary, you can compare the creation dates of the whatis file to the whatis_old file to see if any changes occurred: a. Run the more command against the whatis file: more /usr/share/man/whatis b. After reviewing the displayed file, exit by entering the letter q at the percentage (%) prompt. c. Repeat Steps a. and b. for the whatis_old file. Verify That ZPHIRNM Ran Successfully 1. Review the log file. 2.
Running ZPHIRNM Verify That ZPHIRNM Ran Successfully G06.
11 Loading the G06.28 RVU This section describes how to load the G06.28 version of the NonStop operating system into the memory of each processor in a NonStop S-series server. Unless OSM is installed and configured, TSM is used to load the system processors. Alerts Before performing a system load: • Before halting the processors, stop any applications that are still running, including TMF. Note.
Loading the G06.28 RVU Halt the Processors Halt the Processors Note. These steps are similar whether you are using the TSM or OSM Low-Level Link. 1. If necessary, log on to the TSM Low-Level Link Application or the OSM Low-Level Link. 2. On the toolbar, click Processor Status to display the Processor Status dialog box. 3. In the Processor Status box, select all processors. 4. From the Processor Actions list, select Halt. For example: VST800.vsd 5. Click Perform action. 6.
Loading the G06.28 RVU Replace Processor or Other System CRUs 7. When the Action Status box confirms that all processors have halted, close the Processor Status dialog box. For example: VST830.vsd 8. Close the OSM Service Connection or TSM Service Application window and any OutsideView windows, but do not log off of the OSM or TSM Low-Level Link Application. You will use it to perform a system load in the next procedure. Replace Processor or Other System CRUs Note.
Loading the G06.28 RVU System Load Using the TSM or OSM Low-Level Link System Load Using the TSM or OSM Low-Level Link The operating system is loaded from disk into the memory of one processor (an operation sometimes also called a device load or cold load). All possible paths to processor 0 are tried. If these fail, all possible paths to processor 1 are tried. The remaining processors are loaded by commands in the CIIN file. The initial TACL process stops after executing the CIIN file. 1.
Loading the G06.28 RVU System Load Using the TSM or OSM Low-Level Link 7. Monitor the System Status (which contains initial high-level messages) and Detailed Status (which contains low-level messages) boxes. For example, as shown in TSM: VST810.vsd Messages indicate the progress and completion of the system load and the reload of any processors configured in the CIIN file to start.
Loading the G06.28 RVU Reload the Remaining Processors (If Necessary) Reload the Remaining Processors (If Necessary) After the first processor is loaded, the initial TACL process automatically invokes the CIIN file unless the CIIN file is disabled. The CIIN file contains commands that establish the permanent TACL process pair for the system console. The CIIN file might also contain commands to reload all processors.
Loading the G06.28 RVU Check the Status of the Processors CPU 1: reloaded. CPU 2: reloaded. CPU 3: reloaded. Check the Status of the Processors 1. Select Processor Status to display the Processor Status dialog box. 2. When all processors are executing the NonStop operating system, continue with the upgrade procedure. Recovery Operations for System Load If the system load operation from the newly updated disk fails in any way: 1.
Loading the G06.28 RVU The Reset Operation Because the primary system disk is powered off, the system load is forced to use the mirror disk half (normally, the disk with the latest disk label timestamp is used, and the other disk half is placed in a STOPPED state). The system load uses the mirror disk regardless of its state when the system was stopped. Note.
12 Resuming Normal Operations Several tasks must be performed after system load before you resume normal system operations, as described in this section.
Resuming Normal Operations Step 1: Copy the Sample TCP/IP Files Into $SYSTEM.ZTCPIP (Optional) Step 1: Copy the Sample TCP/IP Files Into $SYSTEM.ZTCPIP (Optional) You need to copy the sample files if you do not have any of these TCP/IP configuration files in your $SYSTEM.ZTCPIP subvolume: • • • • • • HOSTS PROTOCOL NETWORKS PORTCONF RESCONF SERVICES Perform a FUP DUP operation to rename the sample configuration files from the G06.28 SUT to the real file name. Note.
Resuming Normal Operations Step 2: Check the PROTOCOL File Step 2: Check the PROTOCOL File Caution. Even if you are running TCP/IPv6 in IPv4 or conventional TCP/IP mode, you must check that the PROTOCOL file contains ipv6 and icmpv6 entries. If these entries are absent, a network failure might occur because the new socket routines present in TELSERV, LISTNER, and FTP access the entries in the PROTOCOL file. If the PROTOCOL configuration file exists in $SYSTEM.
Resuming Normal Operations Reconfigure System Console Applications Applications use the SERVICES file to retrieve the service port numbers and service names. If you copied files as documented in Step 1, check that the last lines of the SERVICES file have an entry similar to: phiwsock 1089/tcp #DSM/SCM Planner Interface For DSM/SCM, the port number is user-definable. The setup default is 1089. In the ZDSMSCM subvolume, check the INITSTAT file for the recently configured TCP/IP port number.
Resuming Normal Operations Perform Other Firmware Updates Perform Other Firmware Updates Update SWAN and SWAN 2 CLIP Firmware If you have a ServerNet wide area network (SWAN) concentrator connected to your NonStop S-series server, follow the instructions in Appendix C, Updating SWAN Concentrator CLIP Firmware, to update the CLIP firmware after doing a system load of the G06.28 RVU.
Resuming Normal Operations Update ServerNet/FX and ServerNet/FX2 Firmware Note that the ServerNet/FX and ServerNet/FX 2 adapters do not have the autofirmup feature. Use either the TSM Service Application or, if installed, the OSM Service Connection. Only an HP service provider is authorized to install and configure an FCSA and G4SA. Update ServerNet/FX and ServerNet/FX2 Firmware ServerNet/FX and ServerNet/FX 2 adapters cannot be managed automatically through the autofirmup feature.
Resuming Normal Operations Update ServerNet/FX and ServerNet/FX2 Firmware To Set a Cluster Number (Using TSM) 1. In the TSM Management window, select the FXSA FRU. 2. Select Display> Actions to display the TSM Actions dialog box. 3. Select Set FOX Cluster Number and then click Perform Action. 4. Select an integer number from 1 through 14 for a new cluster number, making sure that it is different from the current cluster number. 5. To start the FXSA FRU, click Start and then click Perform Action. 6.
Resuming Normal Operations Update ServerNet/FX and ServerNet/FX2 Firmware 5. Click to highlight (shift-select to highlight multiple) FRUs to be stopped and click Add to move them to the lower resource list. For example: VST450.vsd 6. After moving all FXSA or FX2SA FRUs to be stopped to the lower resource list, click Perform Action. Note. The associated LBU is also stopped. 7.
Resuming Normal Operations Configure the Spooler Confirmation dialog boxes prompt you to enter an (optional) alternative to the default file location. The Progress bar at the bottom of the Multi-Resource Actions dialog box tracks the success or failure of each action. (Click Action Summary to get details on failed actions). 8. Upon successful completion of the firmware updates, select Start from the Action list to start selected FRUs (and their associated LBUs). 9.
Resuming Normal Operations Start User and System Applications Start User and System Applications You can now start your application software. Follow your site’s procedures for executing the system configuration and startup (command) files to accomplish this. DSM/SCM is often started automatically by a system command file. If not, you must start it manually as described next. Before Starting DSM/SCM Initialize SQL 1. Check that TMF is started: > TMFCOM STATUS TMF 2.
Resuming Normal Operations Start DSM/SCM Start DSM/SCM 1. Run the STARTSCM macro from the ZDSM/SCM subvolume to start DSM/SCM: > RUN STARTSCM These messages appear: 8> startscm DSM/SCM Process Startup Function - STARTSCM - T6031D46 - (31MAR2003) Copyright Hewlett Packard Development Company L.P. 1993-2003 NOTICE: * * * * If the hometerm chosen during INITENV, $zhome, is not currently in a paused state, STARTSCM and DSM/SCM server processes may hang indefinitely.
Resuming Normal Operations Configure Specific Products (Post-System Load) command moves the disk into the STOPPED state, substate DOWN, from which it can be started. For example: > scf SCF - T9082G02 - (14JAN02) (03JAN02) - 04/28/2003 10:54:23 System \TEENY Copyright Compaq Computer Corporation 1986 - 2002 (Invoking \TEENY.$SYSTEM.STARTUP.SCFCSTM) 1-> reset disk $system 2-> start disk $system STORAGE W01001 To START the disk, SCF must revive the information on \TEENY.$SYSTEM.
Resuming Normal Operations Configure OSS changes and all defect repair changes are described in the T9057G06^AFQ or later softdoc. In summary, the latest Expand T9057 SPRs remove the use of Super Timefactors in Expand routing. The original time factor method of routing used before T9057G06^AEM (G06.08 RVU) is now used starting with SPR T9057AFL and G06.20. SPEEDK is now mapped to a time factor, and values of SPEEDK for FOX networks or faster are mapped to a time factor of 1.
Resuming Normal Operations • OSS Unautomated Configuration and Startup If no OSS files are managed by DSM/SCM, use COPYOSS for all of the OSS pax archives in the ZOSSUTL subvolume. See the OSS Management and Operations Guide for a description of COPYOSS use or the copyoss(8) reference page in the OSS Shell and Utilities Reference Manual. Then use PINSTALL to install any pax archives in other subvolumes.
Resuming Normal Operations Configure SMF (Optional) As of G06.23, OSS EasySetup no longer requires the process $NULL and the installation of SPI template files. The product NULL (T6025) is still included on each SUT. Configure SMF (Optional) If you plan to configure SMF, an optional product, note: • • • Migration of data from direct volumes to SMF logical volumes is documented in the Storage Management Foundation User's Guide.
Resuming Normal Operations Upgrade the WAN Manager (T8365) (Optional) Upgrade the WAN Manager (T8365) (Optional) The version of WAN Manager (WANMGR) delivered in the G06.07 and later RVUs removes the limitation of configuring 100 SWAN adapters. Starting with the G06.07 RVU, the number of adapters you can configure is determined by the amount of memory available to the WAN manager. See the T8365 softdoc for information on the default WANMGR startup configuration and how to use SCF to increase it.
Part II. Fallback Tasks Part II describes the tasks for falling back from the G06.28 RVU to a G06.06 or later RVU. If you encounter a problem that cannot be resolved while running G06.28, you can fall back to your previous G-series RVU, provided you have already installed the appropriate fallback SPRs for your system. These sections describe the tasks for falling back to your previous RVU from G06.
Part II. Fallback Tasks G06.
13 Preparing to Fall Back If you encounter a problem that cannot be resolved while running the G06.28 RVU, you can fall back to a G06.06 or later G-series RVU, provided that you have already installed the appropriate fallback SPRs, as described in Section 3, Installing SPRs Before Upgrading to the G06.28 RVU. If you did not install the appropriate fallback SPRs before installing the G06.28 RVU, contact your service provider. Alerts Before falling back from the G06.28 RVU: • • • Review G06.
Preparing to Fall Back • • Summary of Fallback Tasks Starting with the G06.23 RVU, there are fallback considerations regarding NonStop SQL/MX Release 2.0. See NonStop SQL/MX Release 2.1.1 on page 1-34. For NonStop SQL/MX Release 2.0, to minimize the risks involved in falling back without a clean TMF shutdown, use the appropriate SQL (MX or special MP) GOAWAY utility to delete all native-format SQL/MX objects and their resource forks.
Preparing to Fall Back Fallback Considerations for Specific Products Fallback Considerations for Specific Products You might need to perform additional tasks for these products: • DP2 • DLLs • DSM/SCM • Spooler • OSS • OSM and TSM • SMF • NonStop SQL/MX 2.0 or 2.0.1 • TMF • WAN Manager (T8365) DP2 If you have set the AUDITTRAILBUFFER or the SQLMXBUFFER attribute to 128 or more, you need to reset the value to 0 before falling back to G06.16 or earlier RVU.
Preparing to Fall Back DSM/SCM See the appropriate programming documentation for details on C++ and compilers. For a list of participating products, see the Interactive Upgrade Guide 2. DSM/SCM You must run the FALLBACK macro before starting DSM/SCM unless you are currently on T6031D46^ABK. See DSM/SCM on page 1-29. If you fall back to a pre-D46 product version and then migrate to a G06.18 or later RVU, DSM/SCM might notify you during the Apply that the CLEANOSS macro must be run.
Preparing to Fall Back SMF SMF The record format of the system configuration database sometimes changes between RVUs and is automatically converted to the new format the first time the system is loaded. To ensure system configuration integrity, always: 1. Save the system configuration after SMF configuration changes are made. 2. Reload the system from the current system configuration file or the latest version with SMF changes. Caution. Create a saved version of the configuration before loading a new RVU.
Preparing to Fall Back WAN Manager (T8365) WAN Manager (T8365) The version of WAN Manager (WANMGR) delivered in G06.07 and later RVUs includes an SPR (first introduced by T8365AAJ) that removes the limitation of configuring a maximum of 100 SWAN adapters. Starting with the G06.07 RVU, the number of adapters that you can configure is determined by the amount of memory available to the WAN manager. If you have installed more than 100 SWAN adapters and have to fall back to a pre-G06.
14 Backing Out the DSM/SCM Revision This section describes how to submit a DSM/SCM backout request to return to your previous RVU from G06.28. You must run the DSM/SCM FALLBACK macro from the ZDSMSCM subvolume. The FALLBACK macro can be exported from any D46 PVU in the DSM/SCM archive and then placed in the ZDSMSCM subvolume. You must run the FALLBACK macro if you are not already running DSM/SCM T6031D46^ABK. Before Backing Out the Revision 1. Confirm that the spooler is active and not 100 percent full. a.
Backing Out the DSM/SCM Revision Start the Target Interface (ZPHITI) Start the Target Interface (ZPHITI) 1.
Backing Out the DSM/SCM Revision Submit a Backout Request Submit a Backout Request 1. From the ZPHITI Main Menu, enter 3 (Perform target activities) in the Selection number field, and press F1.
Backing Out the DSM/SCM Revision Submit a Backout Request 3. In the Selection number field, enter 2 (Perform backout to S/W), and press F1.
Backing Out the DSM/SCM Revision Submit a Backout Request DSM Software Configuration Manager Backout - Processing Backout ============================================================================== \ELI Prior snapshot 2002-04-14:18:03:03 DEFAULT Last S/W applied on SYS00 on 2000-04-14:18:01 Backout 2000-04-18:10:59:34 ============================================================================== Request is being processed. Status information will appear below indicating progress.
Backing Out the DSM/SCM Revision Submit a Backout Request A complete set of operator instructions might look like this: DSM Software Configuration Manager Backout - Complete Backout ============================================================================== \ELI Prior snapshot 2002-04-14:18:03:03 DEFAULT Last S/W applied on SYS on 2000-04-14:18:01 Print operator instructions on: ============================================================================== Placement of files for this Backout is complet
Backing Out the DSM/SCM Revision Monitor the Backout Process Monitor the Backout Process 1. Log on to DSM/SCM (Start>Programs>Dsm_scm>DSMSCM). 2. Select Requests> Requests list. The Requests dialog box appears, showing the type and status of various DSM/SCM requests. 3. From the Request list, double-click your backout request. The Status dialog box displays detailed information about your backout request. This example indicates that the backout request finished successfully: vst100.vsd G06.
Backing Out the DSM/SCM Revision Monitor the Backout Process G06.
15 Returning Firmware to Previous Versions This section describes how to return processor boot code, SP firmware, and SCSI boot code back to earlier product versions before loading the previous operating system image. Alerts Processor Boot Code If you are returning to an RVU prior to the G06.16 RVU, you must return processor boot code back to the earlier PVU before performing a system load of your previous RVU. If you are returning to the G06.
Returning Firmware to Previous Versions Return the Processor Boot Code to the Previous Version For example: $SYSTEM SUPER 8> vproc $system.sys01.cpucode9 VPROC - T9617G03 - (30 MAR 1999) SYSTEM \ELI Date 21 MAR 2000, 11:30:35 COPYRIGHT TANDEM COMPUTERS INCORPORATED 1986 - 1995 $SYSTEM.SYS01.CPUCODE9 Binder timestamp: Version procedure: 25AUG1999 13:42:26 T7892G05^03SEP99^25Aug99^ where SYS01 is the previous operating system image subvolume.
Returning Firmware to Previous Versions Download the Previous SP Firmware File to the System Console Use this information to verify that the update to the previous version was successful. Download the Previous SP Firmware File to the System Console Download the previous SP firmware file into the spcode9 directory on the hard drive of your system console in the event you encounter problems when updating the SP firmware.
Returning Firmware to Previous Versions Return the SCSI Boot Code to the Previous Version (Using TSM) To check the new version of SCSI boot code, enter: >VPROC $SYSTEM.SYSnn.IBOOT Use this information from the VPROCs to verify that the update to the previous version was successful. Return the SCSI Boot Code to the Previous Version (Using TSM) From the TSM Service Application, use the Firmware Update dialog box to update the SCSI boot code for each PMF CRU in your system: 1.
Returning Firmware to Previous Versions Returning SP Firmware to the Previous Version (Using OSM) Returning SP Firmware to the Previous Version (Using OSM) 1. Log on to the OSM Service Connection. 2. Select Display>Multi-Resource Actions. The Multi-Resource Actions dialog box appears with unselected fields. 3. From the Resource Type list, select SP. 4. From the Action list, select SP Firmware Update. 5. From the Filter by list, select the appropriate filter, Logical:Fabric Side-Y first. 6.
Returning Firmware to Previous Versions Returning Boot Code Firmware to the Previous Version (Using OSM) 15. Repeat steps to update the SP firmware, X-side. 16. Check that all SPs have completed successfully. Returning Boot Code Firmware to the Previous Version (Using OSM) 1. Log on to the OSM Service Connection. 2. Select Display> Multi-Resource Actions. The Multi-Resource Actions dialog box appears with unselected fields. 3. From the Resource Type list, select SP. 4.
Returning Firmware to Previous Versions Returning Boot Code Firmware to the Previous Version (Using OSM) When you change the filter from Y-side to X-side, this message appears: Changing a required filter results in your selections being cleared. Do you still wish to change the filter? 13. Click OK. 14. Click Add All to add the SPs you want to update to the lower resource list. 15. Click Perform Action. 16. Click OK when the Confirm Processor Boot Millicode Firmware Update dialog box appears.
Returning Firmware to Previous Versions Returning Boot Code Firmware to the Previous Version (Using OSM) G06.
16 Running ZPHIRNM to Reactivate the Previous Software Revision This section describes how to run the ZPHIRNM program again to change the temporary names of the previous product files back to their actual names. Alerts Before running ZPHIRNM: • • • • Applications that use files that are being replaced should not be running. To avoid any possibility of conflict, stop all applications, except for the TMF subsystem, before running ZPHIRNM. You must have rename (purge) access to all files being renamed.
Running ZPHIRNM to Reactivate the Previous Software Revision Run ZPHIRNM This command causes the spooler to move from the active to the dormant state. Caution. Do not use the TACL STOP command to drain or stop the spooler. Also, do not issue the TACL STOP command after you have issued the SPOOLCOM DRAIN command. The control file can be corrupted during the next warm start or rebuild. For more information on draining the spooler and recovery, the Spooler Utilities Reference Manual, Section 1.
Running ZPHIRNM to Reactivate the Previous Software Revision Verify That ZPHIRNM Ran Successfully Verify That ZPHIRNM Ran Successfully 1. Review the log file. 2. If ZPHIRNM did not run successfully, correct the problem and rerun. Two types of error and warning messages are issued during the renaming process: • • If a fatal error occurs, ZPHIRNM immediately issues an error message and stops.
Running ZPHIRNM to Reactivate the Previous Software Revision Verify That ZPHIRNM Ran Successfully G06.
17 Loading the Previous RVU and Resuming Normal Operations This section describes how to load the previous RVU back into the memory of each processor in the server and resume normal operations. Alerts Before performing a system load, note: • • • • • • If you are returning to an RVU prior to the G06.
Loading the Previous RVU and Resuming Normal Operations Prepare to Stop the System Prepare to Stop the System Before halting the processors: 1. Stop all user applications. 2. Stop TMF and DSM/SCM. For example: 5> TMFCOM STOP TMF 6> VOLUME $dsmscm_vol.ZDSMSCM 7> RUN STOPSCM Halt the Processors Halt all processors from the TSM Low-Level Link Application or from the OSM Low-Level Link. Remove Hardware Installed During Migration If you installed or replaced hardware during your migration to the G06.
Loading the Previous RVU and Resuming Normal Operations Perform a System Load With the Previous SYSnn and CONFxxyy Perform a System Load With the Previous SYSnn and CONFxxyy Perform a system load, except in Step 3, enter the SYSnn of your previous operating system image subvolume, and in Step 4, select the Saved version of the CONFxxyy configuration file that you created under Save the Current Configuration File (CONFxxyy) on page 4-1. Caution. Starting with the G06.
Loading the Previous RVU and Resuming Normal Operations Resume Normal Operations Resume Normal Operations Resume normal operations by invoking the proper startup files to start system processes and user applications after falling back to the previous RVU. Note. If you receive this error message when you attempt to start DSM/SCM: ERROR: *1081* PATHCTL FILE IS INCOMPATIBLE 1. Stop the $YPHI PATHMON process: > VOLUME $dsmscm_vol.ZDSMSCM > STOP $YPHI 2.
Loading the Previous RVU and Resuming Normal Operations Configure Spooler Configure Spooler G06.00 and later RVUs contain spooler product version T9101D46, which introduced a spooler control file in a new format. Although it is still a type 128 file, internally it is considerably different from the format used in the base T9101D41 spooler.
Loading the Previous RVU and Resuming Normal Operations Re-configure DSM/SCM User IDs (If Necessary) G06.
A Using DSM/SCM to Install SPRs SPRs provide new features between RVUs or correct software problems from a previous RVU. This appendix describes tools available for investigating SPRs and instructions on how to install SPRs. Caution. Do not apply any SPR to an RVU without first verifying (using Scout for NonStop Servers, for example) that the SPR can be installed on that specific G-series RVU. See the G06.
Using DSM/SCM to Install SPRs DSM/SCM DSM/SCM DSM/SCM has automatic features that can help you keep records of SPRs. You can use the DSM/SCM Planner Interface to generate a number of prepackaged reports, including reports that list: • • • The products on a system and the SPRs applied to those products The SPRs that have been replaced by a specific SPR The requisite SPRs for a selected SPR You can also use the DSM/SCM Archive to export SPRs to different SYSnns.
Using DSM/SCM to Install SPRs Determine the Current SYSnn 3. Save the current configuration by using a unique file name. At the SCF prompt, enter: -> SAVE CONFIGURATION xx.yy where xx.yy is a number from 0.0 through 99.99. This example saves the current system configuration to the file $SYSTEM.ZSYSCONF.CONF1101: -> SAVE CONFIGURATION 11.1 The configuration file $SYSTEM.ZSYSCONF.CONF1101 has been created. If you specify a configuration file that already exists, SCF asks you if you want to replace it.
Using DSM/SCM to Install SPRs Receive the SPR Into the DSM/SCM Archive 3. At a TACL prompt, enter a STATUS 0,0 command to see which SYSnn subvolume is currently being used: 3> status 0,0 System \ELI Process Pri PFR %WT Userid Program file Hometerm 0,0 201 P R 000 255,255 $SYSTEM.SYS01.OSIMAGE $YMIOP.#CLCI Swap File Name: $SYSTEM.#0 Note. DSM/SCM notifies you in the Build/Apply Request dialog box if a SYSGEN is required and then runs SYSGEN automatically.
Using DSM/SCM to Install SPRs Create a New Software Configuration That Includes the SPR 9. In the Receive Software Request dialog box, click Scheduling. 10. Enter the time you want your Receive Software Request to run. The default option is for the request to run immediately. If this is what you want, click OK. Create a New Software Configuration That Includes the SPR After the SPR has been received into the Archive, you can copy it. To create a new software configuration that includes the SPR: 1.
Using DSM/SCM to Install SPRs Print Operator Instructions From the Target Interface (ZPHITI) This step updates the Software in Archive window to show the newly received software. 8. Exit the DSM/SCM Planner Interface. Print Operator Instructions From the Target Interface (ZPHITI) 1. Make sure that spooler is active. 2. On the DSM/SCM subvolume, enter: RUN ZPHITI The TI Logon screen appears. 3. Enter your user ID/alias and password and press F1 to log on to the Target Interface. The Main Menu appears. 4.
Using DSM/SCM to Install SPRs • • If Running INSTALL^TEMPLATES Is Required $vol specifies the default current system load volume, usually $SYSTEM. SYSnn specifies the current or new (depending on whether SYSGEN was required) SYSnn subvolume. For example: > RUN ZPHIRNM $system.SYS00 2. When asked if you want to use a log file with the session, enter Y. 3. When prompted, enter a file name for the log file.
Using DSM/SCM to Install SPRs If Running INSTALL^TEMPLATES Is Required Note. If you run the INSTALL^TEMPLATES macro with no arguments, you are prompted to provide required information. For information on the INSTALL^TEMPLATES arguments, print the usage notes: -> volume $system.zinsaids -> load /keep 1/ TACLMACS -> install^templates /out outdev/ help where outdev is the name of the desired output device. 3. Choose a location on $SYSTEM to keep updated template files: tacl>volume $system.template 4.
Using DSM/SCM to Install SPRs If a System Load Is Required To correct the problem: 1. Rename the current files: tacl> rename newres, oldres tacl> rename newnres, oldnres 2. Run the INSTALL^TEMPLATES macro again and use the file names newres and newnres. This message indicates that the templates are successfully installed: >$SYSTEM.SYS00.FUP /NAME $Z03M,INV :INBUF.1,OUTV :OUTBUF.
Using DSM/SCM to Install SPRs Perform a System Load Perform a System Load When you perform a system load, the operating system is loaded from disk into the memory of one processor. (This operation is sometimes called a device load or cold load.) All possible paths to processor 0 are tried; if these fail, all possible paths to processor 1 are tried. The remaining processors are loaded by commands in the CIIN file. The initial TACL process stops after executing the CIIN file. 1.
Using DSM/SCM to Install SPRs Reload the Processors (If Necessary) The other processors are now primed for reload. 4. On the toolbar of the OSM Low-Level Link or TSM Low-Level Link Application window, select Processor Status. The Processor Status dialog box should show Executing NonStop OS. EMS event stream and startup TACL windows are automatically launched on the system console. The process might take a few seconds. Note.
Using DSM/SCM to Install SPRs Start Your Applications and Processes G06.
B Installing the Latest DSM/SCM SPRs and Client Software Note. • • • • • You can install the T6031G02 PVU client either before or after installing the T6031ABR SPR. However, this appendix describes installing the T6031ABR SPR first on the server side and then installing the client. HP recommends that you always upgrade to the newest server SPR and client before installing the latest RVU. The latest DSM/SCM client version (T6031G02) is available only on the SUT unless you have ordered new system consoles.
Installing the Latest DSM/SCM SPRs and Client Software Table B-1. G-Series DSM/SCM PVUs and SPRs (page 2 of 3) PVU SPR RVU Description (Major changes) T6031D46 ABE G06.19 Provides an updated version of the DSM/SCM CNFGINFO tool. OSS developers can use this tool to create A7CINFO files in their products' DSVs. A7CINFO files are required by DSM/SCM for automated OSS file management. T6031D46 ABF G06.
Installing the Latest DSM/SCM SPRs and Client Software Table B-1. G-Series DSM/SCM PVUs and SPRs (page 3 of 3) PVU SPR RVU Description (Major changes) T6031D46 ABP G06.26 T6031ABP (available for G06.21 through G06.26) allows a NonStop S-series host to be able to receive H-series SUTs and install and manage software for an Integrity NonStop NS-series target system. G06.27 The PVU removes the necessity for unnecessary system loads. New changes to INITENV are also included. G06.
Installing the Latest DSM/SCM SPRs and Client Software Before You Begin Installing the Software Identification (SWID) and DSM/SCM SPRs Before You Begin Installing the Software Identification (SWID) and DSM/SCM SPRs Besides upgrading the T6031 client and server SPRs for DSM/SCM, you must also upgrade the Software Identification (SWID) (T9298G02) product at the same time to avoid a problem with mismatched files.
Installing the Latest DSM/SCM SPRs and Client Software $DSMSCM.ZDSMSCM.TAEXE Binder timestamp: Version procedure: Version procedure: Target CPU: AXCEL timestamp: Privileged code: Determine the Product Version of DSM/SCM on the Client 03AUG2005 05:54:43 S7032D20^27FEB04^SWARCCP^AAH T6031G02_30AUG2005_03AUG05G02 UNSPECIFIED 03AUG2005 05:59:09 YES \bitty $DSMSCM.
Installing the Latest DSM/SCM SPRs and Client Software Copy (RESTORE) the T6031ABR DSM/SCM Product Version and SWID to Disk Copy (RESTORE) the T6031ABR DSM/SCM Product Version and SWID to Disk To copy the T6031ABR product version of DSM/SCM and the SWID product from the G06.28 RVU to disk, at a TACL prompt, enter the RESTORE command: >RESTORE/OUT $S.#nnn.DSM/$tape, ($*.*6031*.*,$*.*9298*.
Installing the Latest DSM/SCM SPRs and Client Software Receive the G02 SPRs for DSM/SCM VST353.vsd 5. Under Options, click Input source. DSM/SCM displays the Request Source Options dialog box. 6. Select Volume.subvolume. 7. In the Add text box, enter each distribution subvolume for the DSM/SCM files that you specified earlier in the RESTORE command: $DSMSCM.R6030D31 $DSMSCM.R6031G02 8. Click OK. You are returned to the Receive Software Request dialog box. 9. Click OK to run the request immediately.
Installing the Latest DSM/SCM SPRs and Client Software Receive the G02 SPRs for DSM/SCM The Status dialog box appears. Wait until the display for the Request activity summary appears as Complete, and then close the Status window. For example: SOFTWARE 2002-12-07-19:09:39 Input software Complete VST351.vsd 10. Select Window>Refresh to update the Software in Archive dialog box to include the received software. G06.
Installing the Latest DSM/SCM SPRs and Client Software Create a New Software Revision for DSM/SCM G02 SPR and G02 SWID Create a New Software Revision for DSM/SCM G02 SPR and G02 SWID 1. In the Configuration Revisions dialog box, select the target system being upgraded and the current revision of the system being upgraded. Select New software revision. DSM/SCM opens the New dialog box listing the products in the last software revision that was built for the target.
Installing the Latest DSM/SCM SPRs and Client Software Build and Apply the DSM/SCM G02 Software Revision 4. Edit the revision notes for the new revision: a. Click Edit revision notes. The Revision Notes box appears, containing the existing revision notes. b. Enter a description of the changes to the existing text. For example, you might enter: Added 08/07/05: G02 DSM and SWID c. Click OK to add a written history of revisions to existing notes.
Installing the Latest DSM/SCM SPRs and Client Software Build and Apply the DSM/SCM G02 Software Revision c. Click OK. VST254.vsd DSM/SCM runs the Build/Apply requests and displays a Status dialog box that is automatically updated at regular intervals. 5. Check EMS messages for more detailed information about your Build/Apply: • • • From the Status window, click Show EMS events. In the EMS Events window, click Refresh to see newer messages. When finished viewing, click Close. 6.
Installing the Latest DSM/SCM SPRs and Client Software Rename the Applied DSM/SCM G02 Files Rename the Applied DSM/SCM G02 Files 1. Stop DSM/SCM: > VOLUME $dsmscm_vol.ZDSMSCM > RUN STOPSCM where $dsmscm_vol is the DSM/SCM volume. 2. Run ZPHIRNM: > RUN ZPHIRNM $volume.SYSnn where SYSnn is the current SYSnn (because no SYSGEN or system load is required). 3. When asked if you want to use a log file with the session, enter Y. 4. When prompted, enter a file name for the log file.
Installing the Latest DSM/SCM SPRs and Client Software Restart Applications Restart Applications You can now start your application software. Follow your site’s procedures for executing the system configuration and startup (command) files to accomplish this. DSM/SCM is often started automatically by a system command file. If not, you must start DSM/SCM manually, as described next. Before Starting DSM/SCM 1. Check that TMF is started: > TMFCOM STATUS TMF 2.
Installing the Latest DSM/SCM SPRs and Client Software Verify That the Newest Product Version of DSM/SCM Is Installed 2. If necessary, press Enter to have STARTSCM run the IPM6031 TACL macro automatically. This step takes several minutes. STARTSCM: A new version of DSM/SCM has been installed and IPM6031 needs to be run. You can either exit and run IPM6031 manually or continue and IPM6031 will be run for you. Enter to continue or BREAK to exit.
Installing the Latest DSM/SCM SPRs and Client Software Recovery for Problems While Installing the G02 PVU of DSM/SCM The latest SWID SPR for G06.28 is: VPROC - T9617G03 - (07 AUG 2003) SYSTEM \IT Date 06 JAN 2006, 02:02:49 Copyright 2003 Hewlett-Packard Development Company, L.P. $SPRS.R9298G02.
Installing the Latest DSM/SCM SPRs and Client Software Determine Your DSM/SCM Client Software Version Limited DSM/SCM operation is available if you run T6031G02 client software with pre-AAO server software. HP recommends that both the DSM/SCM product version and DSM/SCM client be at the same version level at all times. Determine Your DSM/SCM Client Software Version To determine which version of DSM/SCM client software is installed, start the DSM/SCM Planner Interface.
Installing the Latest DSM/SCM SPRs and Client Software Copy the ZDSMSCM Client File From the Host Copy the ZDSMSCM Client File From the Host Note. If you are not using OutsideView on the PC that manages DSM/SCM: 1. On the NonStop operating system host system, make $dsmscm_vol.ZDSMSCM the current subvolume. 2. To check for the file, enter: $DSM ZDSMSCM 86> fi zdsmexe $DSM.ZDSMSCM CODE ZDSMEXE 0 EOF 2079732 LAST MODIFIED 23DEC2004 2:19 OWNER RWEP 255,255 NUNU PExt 4 SExt 28 3.
Installing the Latest DSM/SCM SPRs and Client Software Install the DSM/SCM Client Software Install the DSM/SCM Client Software 1. Using Windows Explorer, double-click Setup.exe. A DSM/SCM Setup screen appears, and an Enter Object Manager Server Class dialog box appears with the default OM-001. VST010.vsd 2. Click Next to accept the default. The Enter Software Product Group Type (shared or private) dialog box appears. VST021.vsd G06.
Installing the Latest DSM/SCM SPRs and Client Software Install the DSM/SCM Client Software 3. Click Next to accept the default (private) or type in shared and click Next. Note. Private software product groups can be used only by the planner who creates the grouping. Shared software product groups can be used by other planners. For more information on these options, see the DSM/SCM User’s Guide. The Enter CNFGINFO Process Name dialog box appears with the default name $ZPHC. VST015.vsd 4.
Installing the Latest DSM/SCM SPRs and Client Software Install the DSM/SCM Client Software The Choose Destination Location dialog box appears with the default path displayed, based on your Windows operating system: VST025.vsd 6. Click Next to accept the default. You are now prompted to enter an IP address: VST030.vsd 7. Enter the IP address for the host system with which DSM/SCM communicates (see Determine the Current IP Address and Port Number on page B-16), and click Next. Note.
Installing the Latest DSM/SCM SPRs and Client Software Install the DSM/SCM Client Software You are now prompted to enter an IP port number: VST035.vsd 8. Enter the IP port number for the Winsock service (see Determine the Current IP Address and Port Number on page B-16), and click Next. Note. If DSM/SCM is not currently configured to communicate with a host system, accept the default IP port number. You can always change this value later by editing the dsmscm.ini file.
Installing the Latest DSM/SCM SPRs and Client Software Create an ERD or ASR Disk You are asked if you would like to run DSM/SCM. VST045.vsd 10. Click No and go to Create an ERD or ASR Disk on page B-22. The setup program adds the DSM/SCM client software to the Windows Start>Programs menu. You can start the DSM/SCM Planner Interface or CNFGINFO tool from the Start>Programs>DSM_SCM submenu. For example: VST130.
Installing the Latest DSM/SCM SPRs and Client Software Create an ERD or ASR Disk 3. If you are running Windows XP: If the Backup utility is set on Wizard Mode, the Backup or Restore Wizard dialog box appears. a. Click Advanced Mode. b. Click Automated System Recovery Wizard and follow the instructions on the screen to create an ASR disk for your system settings and hard-disk configuration information.
Installing the Latest DSM/SCM SPRs and Client Software Create an ERD or ASR Disk G06.
C Updating SWAN Concentrator CLIP Firmware If necessary, you can update the SWAN or SWAN 2 concentrator CLIP firmware after you have completed a system load of the new RVU. You can use either the OSM Service Connection or TSM, depending on which one you have installed. TSM provides a guided procedure for updating firmware for both SWAN and SWAN 2. OSM provides a Multi-Resource Actions dialog box.
Updating SWAN Concentrator CLIP Firmware Using the SWAN Fast Firmware Update Guided Procedure Yellow caution symbols might appear on enclosure icons and on SWANs during the firmware update. These caution symbols should disappear after you have completed the SWAN update. Using the SWAN Fast Firmware Update Guided Procedure Use this procedure if your site has numerous SWANs that need updating and you are using TSM. For online help, open the Help menu or click Help in any of the procedure’s dialog boxes.
Updating SWAN Concentrator CLIP Firmware Using the SWAN Fast Firmware Update Guided Procedure vst832.vsd 3. Select Updating CLIP firmware. 4. Click Start. The Select CLIP Collection dialog box appears. For example: G06.
Updating SWAN Concentrator CLIP Firmware Using the SWAN Fast Firmware Update Guided Procedure vst864.vsd 5. In the Select CLIP Collection dialog box, select the CLIPs to be updated: a. From the Adapter Type list, select either SWAN2 or SWAN. b. Select _All_CLIP_2s_if adapter is SWAN2 or _All_CLIP_s if adapter is SWAN. c. From the CLIP List in Selected Collection, select the required CLIPs and click Add CLIPs. d. Click Use. The Select Action dialog box appears. 6.
Updating SWAN Concentrator CLIP Firmware Using the SWAN Fast Firmware Update Guided Procedure vst835.vsd 8. If you want to start the CLIPs after firmware, select Start CLIPs after Update? Otherwise, click Start after the SWAN CLIP firmware update is complete. 9. Click Update Firmware. TSM stops the SERVER objects and initiates a firmup of the CLIPs. The Firmware Update Progress Dialog box appears. 10. In the Firmware Update Progress dialog box, monitor the SWAN CLIP update progress.
Updating SWAN Concentrator CLIP Firmware Using the SWAN Fast Firmware Update Guided Procedure 11. When you have finished updating firmware, click OK. If you have problems with the Fast Firmware Update, see If the SWAN Fast Firmware Update Fails on page C-7. G06.
Updating SWAN Concentrator CLIP Firmware If the SWAN Fast Firmware Update Fails If the SWAN Fast Firmware Update Fails If any CLIPs fail, you are notified in the Firmware Update Progress dialog box: vst903.vsd 1. To review the reason for the failure, select the corresponding row. A message similar to the following might appear: Object Name: Action State: Error Id: Error Description: Error Id: 1083. Error Description : Recovery: None. $ZZWAN.#SWAN1.2 Failed 1083 Problem: A non-path error occurred.
Updating SWAN Concentrator CLIP Firmware Using the TSM Firmware Update Dialog Box to Update SWAN Firmware To stop the SWAN adapter object, you can also enter the SCF STOP command. For example: 12> SCF STOP ADAPTER $ZZWAN.#51, SUB ALL c. Check if the SWAN adapter is stopped in TSM or use the SCF STATUS SERVER command: 13> SCF STATUS SERVER $ZZWAN.#51.* 5. After the SWAN objects are stopped, try to update the SWAN CLIPs again.
Updating SWAN Concentrator CLIP Firmware List the Names of the SWAN Concentrators and CLIPs List the Names of the SWAN Concentrators and CLIPs Use the TSM Service Application or SCF to list the names of the SWAN concentrators and CLIPs in your system: • Using the TSM Service Application: VST410.vsd • Or (using SCF) enter: 4> scf names adapter $zzwan.
Updating SWAN Concentrator CLIP Firmware Check Location and Version of New SWAN CLIP Firmware Check Location and Version of New SWAN CLIP Firmware The SWAN firmware object code file is a 510 disk file that resides on a NonStop S-series server and is downloaded to the SWAN concentrator CLIP. Check the location and version of the SWAN firmware object code file for the G06.28 RVU. At a TACL prompt, enter the VPROC command: VPROC $SYSTEM.CSSnn.
Updating SWAN Concentrator CLIP Firmware • Check Firmware Version Currently Running in SWAN CLIPs Use the SCF STATUS SERVER $ZZWAN.#conc-name.clip-num, DETAIL command. For example: $SYSTEM ZWANTOOL 14> scf status server $zzwan.#s01.3, detail SCF - T9082G02 - (12JUL99) (15JUN99) - 11/17/1999 09:19:28 System \ELI Copyright Compaq Computer Corporation 1986 - 1999 WAN Manager STATUS SERVER for CLIP State :......... STARTED \ELI.$ZZWAN.#S01.3 Path A..........: CONFIGURED Path B..........
Updating SWAN Concentrator CLIP Firmware Summary of SWAN Concentrator CLIP Firmware Update Steps (Using TSM) Summary of SWAN Concentrator CLIP Firmware Update Steps (Using TSM) Required for Upgrading From T7953AAG and Later Firmware Versions Step 1: Stop the SWAN Concentrator and CLIPs Step 2: Point SWAN Concentrators to the New Firmware Object Code File Step 3: Initiate the Firmware Update Using TSM Step 4: Start the SWAN Concentrator and CLIPs Step 5: Verify That the SWAN CLIPs Are Running the Latest Fi
Updating SWAN Concentrator CLIP Firmware Step 1: Stop the SWAN Concentrator and CLIPs Step 1: Stop the SWAN Concentrator and CLIPs Use the TSM Service Application or SCF to stop the SWAN concentrator and terminate operation of all CLIPs. For example: VST420.vsd Or (using SCF), enter: 5> SCF STOP ADAPTER $ZZWAN.#S01, SUB ALL G06.
Updating SWAN Concentrator CLIP Firmware Step 1: Stop the SWAN Concentrator and CLIPs Verify That CLIPs Are Stopped Use the TSM Service Application or SCF to check that SWAN concentrators and CLIPs are in the STOPPED state. For example, to see the state of the SWAN CLIPs: VST400.vsd To see the state of the SWAN concentrators: VST422.vsd G06.
Updating SWAN Concentrator CLIP Firmware Step 2: Point SWAN Concentrators to the New Firmware Object Code File Or (using SCF), enter: 2-> status server $zzwan.#s01.* WAN Manager STATUS State :......... . . WAN Manager STATUS State :......... . . WAN Manager STATUS State :......... . . SERVER for CLIP STOPPED \ELI.$ZZWAN.#S01.1 SERVER for CLIP STOPPED \ELI.$ZZWAN.#S01.2 SERVER for CLIP STOPPED \ELI.$ZZWAN.#S01.
Updating SWAN Concentrator CLIP Firmware Step 3: Initiate the Firmware Update Using TSM Step 3: Initiate the Firmware Update Using TSM 1. Log on to the TSM Service Application. 2. Select Display> Firmware update. The Firmware Update dialog box appears. 3. From the Resource Type list, select SWAN Clip. 4. From the Display list, select All. The SWAN CLIPs are listed in the Available box: VST425.vsd 5.
Updating SWAN Concentrator CLIP Firmware Step 3: Initiate the Firmware Update Using TSM 8. In the $volume.subvolume box, enter the new firmware file location (the value you entered in the SCF ALTER ADAPTER, KERNELCODE command in Step 2: Point SWAN Concentrators to the New Firmware Object Code File). For example: VST430.vsd 9. Click OK. 10. Click Yes when a message appears, warning that you have specified a nonstandard firmware file location. 11. In the Firmware Update dialog box, click Perform action.
Updating SWAN Concentrator CLIP Firmware Step 4: Start the SWAN Concentrator and CLIPs Step 4: Start the SWAN Concentrator and CLIPs After the SWAN CLIP firmware has been updated, use the TSM Service Application or SCF to start the updated SWAN concentrator and CLIPs.
Updating SWAN Concentrator CLIP Firmware Step 1: Stop the SWAN Concentrator and CLIPs Step 1: Stop the SWAN Concentrator and CLIPs 1. Select Display>Multi-Resource Actions. The Multi-Resource Actions dialog box appears. 2. From the Resource Type list, select CLIP. 3. From the Action list, select Stop. 4. Select the SWAN CLIPS you want to stop and click Add or Add all. The selected CLIPs are added. Note that they are still in the Started state. VST960.vsd 5. Click Perform action.
Updating SWAN Concentrator CLIP Firmware Step 2: Check the Location and Version of the SWAN Firmware VST951.vsd 6. Click OK. The Progress list shows the status of the CLIP action. 7. Wait until all CLIPs are stopped before proceeding. Step 2: Check the Location and Version of the SWAN Firmware In the OSM Service Connection, look under the Firmware heading in the Attribute pane for SWAN CLIPS. The location and the version of the SWAN firmware is displayed.
Updating SWAN Concentrator CLIP Firmware Step 3: Initiate the Firmware Update 5. Leave blank the $SYSTEM.CSSnn subvolume and file name (CP7953P00) created during the most recent DSM/SCM Build/Apply and click OK. Because you have just loaded the new RVU, the SWAN firmware location should point to the correct subvolume and file version. However, if you have performed a Build/Apply for a new SWAN firmware SPR, specify that location and click OK. 6.
Updating SWAN Concentrator CLIP Firmware Step 4: Start the SWAN Concentrator and CLIPs Step 4: Start the SWAN Concentrator and CLIPs 1. With the Multi-Resource Actions dialog box still open, from the Action list, select Start. 2. Click Add or Add all. 3. Click Perform Action. The SWAN CLIPs should start. If they do not, see the SWAN Concentrator and WAN Subsystem Troubleshooting Guide, Section 4. You can also use SCF to start the CLIP or use the Actions - CLIP dialog box.
Updating SWAN Concentrator CLIP Firmware If a CLIP Fails to Update (Using OSM) c. Use the SCF STATUS SERVER command again to make sure that the SWAN adapter object is stopped. 6. From the Available Actions list, select Firmware Update to update the firmware for that particular CLIP. 7. Click Perform action. 8. Monitor the progress in the Action Status menu. To view details of the action, click Details. 9. To start the individual CLIP, select Start from the Available Actions list and click Perform action.
Updating SWAN Concentrator CLIP Firmware If a CLIP Fails to Update (Using OSM) G06.
Glossary A0CINFO file. A distribution subvolume (DSV) file that contains information about a product and each of its files, including product and file dependencies, how the files are used and where they are placed, and on which type of processor the product runs. Every product and SPR to be managed by the Distributed Systems Management/Software Configuration Manager (DSM/SCM) is distributed in a subvolume, and that subvolume must contain the product’s A0CINFO file. A1CINFO file.
Glossary CLIP CLIP. See communications line interface processor (CLIP). cluster switch. See HP NonStop™ Cluster Switch (model 6770) and HP NonStop™ ServerNet Switch (model 6780). cold load. A synonym for system load or load (in the case of single processor load). System load or load is the preferred term in this and other HP NonStop server system manuals. See system load and load. communications line interface processor (CLIP).
Glossary dynamic-link library (DLL) dynamic-link library (DLL). A collection of procedures whose code and data can be loaded and executed at any virtual memory address, with run-time resolution of links to and from the main program and other independent libraries. The same DLL can be used by more than one process. Each process gets its own copy of DLL static data. Contrast with shared run-time library (SRL). dynamic loading.
Glossary discovery discovery. For the SM package, the process of identifying the resources that exist on a NonStop S-series server. See also incremental discovery and initial discovery. Distributed Systems Management/Software Configuration Manager (DSM/SCM). A graphical user interface (GUI)-based program that installs new software and creates a new NonStop operating system. DSM/SCM creates a new software revision and activates the new software on the target system. DSM/SCM.
Glossary Gigabit Ethernet 4-Port ServerNet adapter (G4SA). Gigabit Ethernet 4-Port ServerNet adapter (G4SA). A multiport ServerNet adapter that provides 1000 megabits/second (Mbps) data transfer rates between HP NonStop™ S-series systems and Ethernet LANs. Global Customer Support Center (GCSC). A support organization that provides telephone and remote diagnostic support for HP customers. There are GCSCs located all over the world. See also Online Support Center (OSC). halt.
Glossary HP NonStop™ S74000 server HP NonStop™ S74000 server. The high-performance successor of the NonStop S72000 line of HP NonStop S-series servers. HP NonStop™ S76000 server. The high-performance successor of the NonStop S74000 line of HP NonStop S-series servers. HP NonStop™ S78000 server. The high-performance successor of the NonStop S76000 line of HP NonStop S-series servers. HP NonStop™ S86000 server.
Glossary HP NonStop™ System RISC Model J processor (NSR-J processor) HP NonStop™ System RISC Model J processor (NSR-J processor). The model designation for the TNS/R processor used in the HP NonStop S7800 server. HP NonStop™ System RISC Model T processor (NSR-T processor). The model designation for the TNS/R processor used in the HP NonStop S72000 server. HP NonStop™ System RISC Model V processor (NSR-V processor). The model designation for the TNS/R processor used in the HP NonStop S74000 server.
Glossary HP NonStop™ Cluster Switch (model 6770) HP NonStop™ Cluster Switch (model 6770). An assembly that routes ServerNet messages across an external fabric of a ServerNet cluster. The cluster switch consists of a ServerNet II Switch, an uninterruptible power supply (UPS), and AC transfer switch, and it can be packaged in a switch enclosure or in a 19-inch rack. The cluster switch is used with star, split-star, and tri-star topologies. See also HP NonStop™ ServerNet Switch (model 6780).
Glossary IOMF 2 CRU IOMF 2 CRU. See I/O multifunction (IOMF) 2 CRU. I/O multifunction (IOMF) CRU. (1) A NonStop S-series server customer-replaceable unit (CRU) that connects the I/O enclosure to a processor enclosure, using a ServerNet cable, and that supplies power to the components within the IOMF CRU, as well as redundantly to the disk drives, SCSI terminators, and ServerNet adapters in that enclosure.
Glossary Physical view Physical view. One of several views of a server available in the view pane of the Management window of the OSM Service Connection, TSM Service Application, and TSM Low-Level Link Application. A Physical view of a server is a view of all the enclosures and is intended to represent the actual floor plan at the site. A Physical view of an enclosure is a visual representation of the physical placement of supported resources inside the enclosure. Planner Interface.
Glossary ServerNet expansion board (SEB) ServerNet expansion board (SEB). (1) A connector board that plugs in to the backplane to allow one or more ServerNet cables to exit the rear of the enclosure. The SEBs and ServerNet cables allow processors in one group to communicate with processors in another group. Each SEB provides either the ServerNet X fabric or the ServerNet Y fabric for a group.
Glossary shared run-time library (SRL) shared run-time library (SRL). A collection of procedures whose code and data can be loaded and executed only at a specific assigned virtual memory address (the same address in all processes). SRLs use direct addressing and do not have run-time resolution of links to and from the main program and other independent libraries. Contrast with dynamic-link library (DLL). shell.
Glossary SWID SWID. The software identification tool invoked by the SYSGENR program that audits file identification information about your software. SYSnn subvolume. A subvolume on the $SYSTEM volume where the new version of the NonStop operating system image is located. Also located on the SYSnn subvolume is system-dependent and RVU-dependent software. nn is an octal number in the range %00 through %77. system console.
Glossary Trivial File Transfer Protocol (TFTP) G06.
Index A A7CINFO files activation package 5-12 introduction, used in installation 1-7 used with OSS and DSM/SCM 1-33 Aborting the system startup process A-10 ALLPROCESSORS paragraph 1-20 Alternate system disk location, specifying 11-4, 11-8, A-10 AUDITTRAILBUFFER parameter, DP2 and RDF performance 12-15 Automated System Recovery (ASR) B-22 B Bootstrap microcode 6-1 Build process, DSM/SCM 5-13 Build/Apply request, defined 1-8 C C7953P00 locating C-10 SWAN firmware object code file C-20 CBEXE determining cur
F Index ESS (Enterprise Storage System) FCHECK utility 1-22 migrating data 1-22 mod-14 extent boundary.
K Index K Kernel-managed swap files 4-14 L Loading system 11-4, 11-7 M MAXEXTENTS 1-30, 4-14 merge_whatis command 10-8 Mirror system disk loading system from 11-7 restarting after REPLACEBOOT 12-11 N Native CRE/RTL product (T8431) 1-42 New software revision, DSM/SCM 5-8 NonStop eServices Portal 1-1 NonStop ServerNet Switch firmware requirements 1-12 updating firmware 12-5 NonStop SQL/MX 13-5 NonStop TCP/IP, sample configuration files 12-2 NonStop TS/MP PATHMON 1-26 NSK CRE/RTL (T1269) 1-42 NSKCOM 4-14
R Index PREVIEW mode 10-5 Primary and backup dial-out, reconfiguring 12-4 Processor boot code description of 8-1 fallback 15-1 updating 8-1 version and location 8-3 Processor reload 11-6 Processor type 1-20 Profiles, target, changing information 5-10 PROTOCOL configuration file 12-3 R RDF interoperability SPRs 3-8 RELOAD command (TACL) 11-6 Reload operation 11-6 REPLACEBOOT 6-1 RVUs 3-1 S S7000 boot millicode 8-1 S7800 CRUs 1-38, 1-39 S7x000 boot millicode 8-1 Safeguard adding as a persistent process 1-
T Index SPRs (continued) RDF 3-8 SQL/MP Format 2 partitions description of 3-6 SQL/MP Release 2.0 Fallback 13-2 SQL/MX falling back 1-35 Metadata tables 1-35 SQL/MX Release 2.
U Index TEMPLI program B-12 TMF fallback from G06.
