HP NonStop G-Series : NET/MASTER RMS Management and Operations Guide : Page 94

Getting Online Help in RMS

Getting Started

4–18 115415 NonStop NET/MASTER RMS Management and Operations Guide

27. Type CLOSTERM &WORD14 in the Command Text field to instruct RMS to close

the terminal at which logon attempts have failed due to incorrect passwords. Your

panel should be similar to the following:

SDPL------------------------ RMS : System Action --------------------Page 5 of 6

Command ===>

Command Text ..... CLOSTERM &WORD14˚˚˚˚˚˚˚˚˚˚˚˚˚˚˚˚˚˚˚˚˚˚˚˚˚˚˚˚˚˚˚˚˚˚˚˚˚˚˚˚˚˚˚˚

NCL Proc Name .... ˚˚˚˚˚˚˚˚˚˚˚˚˚˚˚˚˚˚˚˚˚˚˚˚˚˚˚˚˚˚˚˚˚˚˚˚˚˚˚˚˚˚˚˚˚˚˚˚˚˚˚˚˚˚˚˚˚˚˚˚

Exec Cmd Group ... ˚˚˚˚˚˚˚˚˚˚˚˚

Submit Actions ... ˚˚˚ NCL Queue: ... SAMPLENNM0686

Activate Timer ... ˚˚˚˚˚˚˚˚˚˚˚˚

Set Variables .... ˚˚˚

Load Ruleset ..... ˚˚˚˚˚˚˚˚

NCL Exit Name .... ˚˚˚˚˚˚˚˚˚˚˚˚˚˚˚˚˚˚˚˚˚˚˚˚˚˚˚˚˚˚˚˚˚˚˚˚˚˚˚˚˚˚˚˚˚˚˚˚˚˚˚˚˚˚˚˚˚˚˚˚

----- MESSAGE GROUP TABLE -----

Message Purge Correlation

Group ID After Key

˚˚˚˚˚˚˚˚˚˚˚˚ ˚˚˚˚˚˚˚˚ ˚˚˚˚˚˚˚˚˚˚˚˚˚˚˚˚˚˚˚˚˚˚˚˚˚˚˚˚˚˚˚˚˚˚˚˚˚˚˚˚˚˚˚˚˚˚˚˚˚

Activation: D (I/N/D - Immediate/Immediate No Save/Deferred )

F1=Help F2=Split F3=File F7=Backward F8=Forward

F9=Swap F12=Cancel

28. Press F3 to file the rule definition. The RMS : Message Action Rules Maintenance

panel reappears, and a message appears on the panel to confirm the addition of

the rule.

You have created your ruleset, and you can use the ruleset with a message handler to

automatically handle illegal logons.

Starting the Message

Handler

To test the ruleset SAMPLE, start a message handler as a MSGPROC. You must do

this in an OCS environment. To start a MSGPROC with ruleset SAMPLE, follow these

steps:

Note Normally, you would start this message handler in a background environment so that the handler

continues operation when you exit your OCS window or log off from NonStop NET/MASTER MS.

1. At any => prompt, type =2 and press ENTER to access Operator Control Services.

The OCS window appears.

2. At the M=> prompt, type ZRMSMENN and press ENTER (ZRMSMENN is the

NCL procedure that starts the RMS panel interface). The NonStop NET/MASTER

RMS primary menu panel appears.

3. Select option 1 to access Start RMS Message Handler. The RMS : Start Message

Handler panel appears.