NonStop S-Series Hardware Installation and FastPath Guide (G06.29+)

Performing Post-Startup Tasks
HP NonStop S-Series Hardware Installation and FastPath Guide—541880-002
9-7
Check Disk Subsystem Status
4. Verify that the LISTDEV display includes all processes shown in this example. If
any of these processes do not appear in the display, contact your service provider.
Check Disk Subsystem Status
1. Enter the SCF STATUS DISK command for all disk volumes on the system:
-> STATUS DISK $*
2. Verify that the STATUS DISK display includes all the disk subsystems shown in the
following example and that the primary, backup, mirror, and mirror-backup paths
are all described as STARTED. If any of these disk subsystems do not appear in
the display, or if any of these paths are described as STOPPED, contact your
service provider.
LDev Name PPID BPID Type RSize Pri Program
0 $0 0,5 1,5 ( 1,0 ) 102 201 \NONAME.$SYSTEM.SYS00.OSIMAGE
3 $YMIOP 0,256 1,256 ( 6,4 ) 80 205 \NONAME.$SYSTEM.SYS00.OSIMAGE
5 $Z0 0,7 1,7 ( 1,2 ) 102 200 \NONAME.$SYSTEM.SYS00.OSIMAGE
6 $SYSTEM 0,257 1,257 ( 3,41) 4096 220 \NONAME.$SYSTEM.SYS00.OSIMAGE
7 $ZOPR 0,8 1,8 ( 1,0 ) 102 201 \NONAME.$SYSTEM.SYS00.OSIMAGE
38 $ZZKRN 0,15 1,12 (66,0 ) 132 180 \NONAME.$SYSTEM.SYS00.OZKRN
39 $ZZWAN 0,271 1,275 (50,3 ) 132 180 \NONAME.$SYSTEM.SYS00.WANMGR
40 $ZZSTO 0,272 1,282 (65,0 ) 4096 180 \NONAME.$SYSTEM.SYS00.TZSTO
41 $ZZLAN 0,14 1,15 (43,0 ) 132 180 \NONAME.$SYSTEM.SYS00.LANMAN
45 $ZSNET 0,15 1,12 (66,0 ) 132 180 \NONAME.$SYSTEM.SYS00.OZKRN
46 $ZNET 0,16 1,14 (50,63) 3900 175 \NONAME.$SYSTEM.SYS00.SCP
61 $ZM01 1,11 0,0 (45,0 ) 132 201 \NONAME.$SYSTEM.SYS00.QIOMON
62 $ZM00 0,13 0,0 (45,0 ) 132 201 \NONAME.$SYSTEM.SYS00.QIOMON
63 $ZLOG 0,286 0,0 ( 1,0 ) 4024 150 \NONAME.$SYSTEM.SYS00.EMSACOLL
72 $DSMSCM 0,280 1,261 ( 3,41) 4096 220 \NONAME.$SYSTEM.SYS00.TSYSDP2
79 $AUDIT 0,273 1,271 ( 3,41) 4096 220 \NONAME.$SYSTEM.SYS00.TSYSDP2
85 $ZTCP0 0,299 1,280 (48,0 ) 32000 200 \NONAME.$SYSTEM.SYS00.TCPIP
88 $ZTNP0 0,301 1,276 (46,0 ) 6144 170 \NONAME.$SYSTEM.SYS00.TELSERV
98 $ZTCP1 1,283 0,304 (48,0 ) 32000 200 \NONAME.$SYSTEM.SYS00.TCPIP
100 $ZTNP1 1,285 0,305 (46,0 ) 6144 170 \NONAME.$SYSTEM.SYS00.TELSERV
STORAGE - Status DISK \NONAME.$AUDIT
LDev Primary Backup Mirror MirrorBackup Primary Backup
PID PID
79 *STARTED STARTED *STARTED STARTED 0,273 1,271
STORAGE - Status DISK \NONAME.$DSMSCM
LDev Primary Backup Mirror MirrorBackup Primary Backup
PID PID
72 *STARTED STARTED *STARTED STARTED 0,280 1,261
STORAGE - Status DISK \NONAME.$SYSTEM
LDev Primary Backup Mirror MirrorBackup Primary Backup
PID PID
6 *STARTED STARTED *STARTED STARTED 0,257 1,257