NonStop S-Series System Expansion and Reduction Guide
Table Of Contents
- NonStop S-Series System Expansion and Reduction Guide
- What’s New in This Guide
- About This Guide
- 1 The Resizing Process
- 2 Planning System Expansion
- 3 Planning System Reduction
- 4 Reducing a System Online
- 1.Prepare the Donor System for Reduction
- 2.Record Information About the Donor System
- 3.Prepare Both ServerNet Fabrics
- 4.Inventory Enclosures to Be Removed
- 5.Prepare and Stop Devices and Processes
- 6.Ensure Devices and Processes Are Stopped
- 7.Delete Devices and Processes If Necessary
- 8.Prepare Enclosures for Removal
- 9.Finish the Reduction
- 10.Remove Other Cables From Powered-Off Enclosures
- 11.Physically Remove Enclosures From the System
- Adding Enclosures to Another System
- 5 Reducing a System Offline
- 6 Expanding a System Online
- Preparation for Online Expansion
- 1.Prepare Target System for Expansion
- 2.Record Information About Target System
- 3.Prepare Target System for Addition of Block
- 4.Save Current Target System Configuration
- 5.Copy SP Firmware File From the Target System to the System Console
- 6.Finish Gathering Information
- 7.Connect a System Console to the Enclosure
- 8.Change Group Number of Enclosure to 01
- 9.Power On Enclosure
- 10.Verify Connection Between System Console and Enclosure
- 11.Configure System Console and Enclosure
- 12.Verify SP Firmware Is Compatible
- 13.Update SP Firmware in Enclosure If Necessary
- 14.Configure Topology of Enclosure If Necessary
- 15.Power Off Enclosure
- 16.Repeat Steps 6 Through 15 If Necessary
- 17.Assemble Enclosures Into a Block
- 18.Change Group Numbers of Block to Fit Target System
- 19.Disconnect System Console From Block
- 20.Power On Added Block
- 21.Cable Block to Target System
- 22.Verify Resized Target System
- 23a.Update Firmware and Code in Block (Using TSM)
- 23b.Update Firmware and Code in Block (Using OSM)
- 24.Reload Processors in Block If Necessary
- 25.Verify Operations in Added Block
- 26.Configure CRUs in Added Block
- 7 Troubleshooting
- A Common System Operations
- Determine the Processor Type
- Determine the ServerNet Fabric Status
- Determine the Product Versions of the OSM Client Software
- Determine the Product Version of the TSM Client Software
- Move the System Console
- Stop the OSM or TSM Low-Level Link
- Start a Startup TACL Session
- Start the OSM or TSM Low-Level Link
- Start the OSM Service Connection or TSM Service Application
- B ServerNet Cabling
- C Checklists and Worksheets
- D Stopping Devices and Processes
- Safety and Compliance
- Glossary
- Index

Common System Operations
HP NonStop S-Series System Expansion and Reduction Guide—522465-009
A-6
Check ServerNet Fabric Status Using SCF
(Processor Enclosures Only)
$SYSTEM STARTUP 1> scf
SCF - T9082G02 - (16OCT98) (25SEP98) - 02/22/1999 13:37:32 System \ALPHA5
Copyright Tandem Computers Incorporated 1986 - 1998
(Invoking \ALPHA5.$SYSTEM.STARTUP.SCFCSTM)
1-> status servernet $zsnet
NONSTOP KERNEL - Status SERVERNET
X-FABRIC
TO 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
FROM
00 UP UP UP UP UNA UNA UNA UNA UNA UNA UNA UNA UNA UNA UNA UNA
01 UP UP UP UP UNA UNA UNA UNA UNA UNA UNA UNA UNA UNA UNA UNA
02 UP UP UP UP UNA UNA UNA UNA UNA UNA UNA UNA UNA UNA UNA UNA
03 UP UP UP UP UNA UNA UNA UNA UNA UNA UNA UNA UNA UNA UNA UNA
04 <- DOWN
05 <- DOWN
06 <- DOWN
07 <- DOWN
08 <- DOWN
09 <- DOWN
10 <- DOWN
11 <- DOWN
12 <- DOWN
13 <- DOWN
14 <- DOWN
15 <- DOWN
Y-FABRIC
TO 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
FROM
00 UP UP DN DN UNA UNA UNA UNA UNA UNA UNA UNA UNA UNA UNA UNA
01 UP UP DN DN UNA UNA UNA UNA UNA UNA UNA UNA UNA UNA UNA UNA
02 DN DN UP UP UNA UNA UNA UNA UNA UNA UNA UNA UNA UNA UNA UNA
03 DN DN UP UP UNA UNA UNA UNA UNA UNA UNA UNA UNA UNA UNA UNA
04 <- DOWN
05 <- DOWN
06 <- DOWN
07 <- DOWN
08 <- DOWN
09 <- DOWN
10 <- DOWN
11 <- DOWN
12 <- DOWN
13 <- DOWN
14 <- DOWN
15 <- DOWN