NonStop S-Series System Expansion and Reduction Guide
Table Of Contents
- NonStop S-Series System Expansion and Reduction Guide
- What’s New in This Guide
- About This Guide
- 1 The Resizing Process
- 2 Planning System Expansion
- 3 Planning System Reduction
- 4 Reducing a System Online
- 1.Prepare the Donor System for Reduction
- 2.Record Information About the Donor System
- 3.Prepare Both ServerNet Fabrics
- 4.Inventory Enclosures to Be Removed
- 5.Prepare and Stop Devices and Processes
- 6.Ensure Devices and Processes Are Stopped
- 7.Delete Devices and Processes If Necessary
- 8.Prepare Enclosures for Removal
- 9.Finish the Reduction
- 10.Remove Other Cables From Powered-Off Enclosures
- 11.Physically Remove Enclosures From the System
- Adding Enclosures to Another System
- 5 Reducing a System Offline
- 6 Expanding a System Online
- Preparation for Online Expansion
- 1.Prepare Target System for Expansion
- 2.Record Information About Target System
- 3.Prepare Target System for Addition of Block
- 4.Save Current Target System Configuration
- 5.Copy SP Firmware File From the Target System to the System Console
- 6.Finish Gathering Information
- 7.Connect a System Console to the Enclosure
- 8.Change Group Number of Enclosure to 01
- 9.Power On Enclosure
- 10.Verify Connection Between System Console and Enclosure
- 11.Configure System Console and Enclosure
- 12.Verify SP Firmware Is Compatible
- 13.Update SP Firmware in Enclosure If Necessary
- 14.Configure Topology of Enclosure If Necessary
- 15.Power Off Enclosure
- 16.Repeat Steps 6 Through 15 If Necessary
- 17.Assemble Enclosures Into a Block
- 18.Change Group Numbers of Block to Fit Target System
- 19.Disconnect System Console From Block
- 20.Power On Added Block
- 21.Cable Block to Target System
- 22.Verify Resized Target System
- 23a.Update Firmware and Code in Block (Using TSM)
- 23b.Update Firmware and Code in Block (Using OSM)
- 24.Reload Processors in Block If Necessary
- 25.Verify Operations in Added Block
- 26.Configure CRUs in Added Block
- 7 Troubleshooting
- A Common System Operations
- Determine the Processor Type
- Determine the ServerNet Fabric Status
- Determine the Product Versions of the OSM Client Software
- Determine the Product Version of the TSM Client Software
- Move the System Console
- Stop the OSM or TSM Low-Level Link
- Start a Startup TACL Session
- Start the OSM or TSM Low-Level Link
- Start the OSM Service Connection or TSM Service Application
- B ServerNet Cabling
- C Checklists and Worksheets
- D Stopping Devices and Processes
- Safety and Compliance
- Glossary
- Index
Group 45
IOMF
Group 44
IOMF
Group 43
IOMF
Group 42
IOMF
Group 41
IOMF
55
55
55
55
55
3
2
1
4
5
6
SE
B
52
1
2
3456
SEB
54
PMF 55
Group
04
55
55
55
55
55
Group 21
IOMF
Group 22
IOMF
Group 23
IOMF
Group 24
IOMF
Group 25
IOMF
654321
SE
B
52
SEB
54
PMF 55
Group
06
1
2
3
4
5
6
55
55
55
55
55
Group 65
IOMF
Group 66
IOMF
Group 67
IOMF
Group 68
IOMF
Group 69
IOMF
Group
64
IOMF
Group
63
IOMF
Group
62
IOMF
Group
61
IOMF
55 55 55 55
SEB
54
SE
B
52
1
2
3
4
5
6
PMF 55
Group
05
123456
Group
51
IOMF
Group
52
IOMF
Group
53
IOMF
Group
54
IOMF
55 55 55
55
Group 55
IOMF
Group 56
IOMF
Group 57
IOMF
Group 58
IOMF
Group 59
IOMF
55
55
55
55
55
Group 11
IOMF
Group 12
IOMF
Group 13
IOMF
Group 14
IOMF
Group 15
IOMF
55
55
55
55
55
SEB
54
SE
B
52
6
5
4
1
2
3
PMF 55
Group
01
123456
55
55
55
55
55
Group 35
IOMF
Group 34
IOMF
Group 33
IOMF
Group 32
IOMF
Group 31
IOMF
Group 89
IOMF
Group 88
IOMF
Group 87
IOMF
Group 86
IOMF
Group 85
IOMF
55
55
55
55
55
6
5
4
3
2
1
SE
B
52
123456
SEB
54
PMF 55
Group
08
Group
81
IOMF
Group
82
IOMF
Group
83
IOMF
Group
84
IOMF
55 55 55 55
Group 79
IOMF
Group 78
IOMF
Group 77
IOMF
Group 76
IOMF
55
55
55
55
55
Group 75
IOMF
SE
B
52
654321
SEB
54
PMF 55
6
5
4
3
2
1
Group
07
Group
74
IOMF
Group
73
IOMF
Group
72
IOMF
Group
71
IOMF
55 55 55 55
SE
B
52
654321
SEB
54
PMF 55
3
2
1
4
5
6
Group
03
65 4321
SE
B
52
SEB
54
PMF 55
Group
02
6
5
4
1
2
3
VST213.vsd
Added Blocks: Tetra 16 Topology, Y Fabric
Worksheet 6
Shade in the enclosures, ports, and slot numbers that are in use in your current configuration.
You can now see the available locations and group numbers for added enclosures.
With a highlighter or a pen of a different color, circle where you will add the enclosures.
Note. If your target
system is a Tetra 8
topology with the
maximum number
of enclosures
attached, you
cannot expand it
online. You must
reconfigure it as a
Tetra 16 topology
offline.
Note. This
illustration shows the
maximum possible
number of I/O
enclosures. Your
service provider can
tell you the number
of I/O enclosures
supported by the
RVU running on
your system.